**Huasifei WH3000**
Portable Wi-Fi 6 travel router based on MediaTek MT7981A SoC. MT7981B+MT7976CN+RTL8221B Dual Core 1.3-1.6GHZ
**Specifications**
SoC: Filogic 820 MT7981A (1.3GHz base could be overclocked to 1.6GHz by `unlockoc` in factory firmware it will change a BL image with an overclocked one. If you want to go back to 1.3Ghz, run `lockoc` in factory firmware once)
RAM: DDR4 1GB
Flash: eMMC 8GB
WiFi: 2.4GHz and 5GHz with 3 antennas
Ethernet:
1x WAN (10/100/1000M)
1x LAN (10/100/1000/2500M)
USB: 1x USB 3.0 port
Two buttons: power/reset and mode (BTN_0)
LEDS: blue, red, blue+red=pink
UART: 3.3V, TX, RX, GND / 115200 8N1 (no need to use 3.3V! Use only TX, RX, and GND)
**Installation via U-Boot rescue**
1. Set static IP 192.168.1.2 on your computer and default route as 192.168.1.1
2. Connect to the WAN port and hold the reset button while booting the device.
3. Wait for the LED to blink 5 times, and release the reset button.
4. Open `U-boot` web page on your browser at `192.168.1.1`
5. Select the OpenWRT `sysupgrade` image, upload it, and start the upgrade.
6. Wait for the router to flash the new firmware.
7. Wait for the router to reboot itself.
**Installation via sysupgrade**
Flash the `sysupgrade` file via [LuCI upgrade page](http://192.168.1.1/cgi-bin/luci/admin/system/flash) without saving the settings.
**Installation via SSH**
Upload the file to the router `/tmp` directory, `ssh root@192.168.1.1` and issue a command:
```
sysupgrade -n /tmp/openwrt-mediatek-filogic-huasifei_wh3000-emmc-squashfs-sysupgrade.bin
```
**MAC addresses**
You can find your Factory MAC, which is mentioned on the box at `/dev/mmcblck0p2` partition `factory` starting from `0x4`
```
dd if=/dev/mmcblk0p2 bs=1 skip=4 count=6 | hexdump -C
```
Factory MAC is on the label, e.g. `XX:XX:XX:XX:XX:A8`
LAN (eth0) is factory + 2, e.g. `XX:XX:XX:XX:XX:AA`
WAN (eth1) is factory + 3, e.g. `XX:XX:XX:XX:XX:AB`
WLAN (2.4G) is factory, e.g. `XX:XX:XX:XX:XX:A8`
WLAN (5G) is factory + 1, e.g. `XX:XX:XX:XX:XX:A9`
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Backport FORESEE NAND chip support from upstream Linux. The newly
introduced FORESEE F35SQA001G was found on the Xiaomi AX3000T.
Signed-off-by: Erik Servili <serverror@serverror.com>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit 302c717aa3a434676a32a4dde8b10ec2c03798b5)
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 64GB eMMC or 128 MB SPI-NAND
RAM: 512MB DDR3 or DDR4
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
Gain SSH access:
1. Login into web interface, and download the configuration.
2. Get the SN of the device from web interface or the label on the back of the device.
3. Calculate configuration decryption password:
Command "eval" is necessary here as the encryption implentation treats '$...' as (empty) variables.
decpwd="$(eval echo $(openssl passwd -1 -salt aV6dW8bD "your_device_sn"))"
4. Decrypt the configuration:
openssl aes-256-cbc -d -pbkdf2 -k "$decpwd" -in cfg_export_config_file.conf -out cfg_export_config_file.conf.dec
5. Enter fakeroot, decompress the configuration:
tar -zxf cfg_export_config_file.conf.dec
6. Edit 'etc/shadow', update (remove) root password: 'root::19179:0:99999:7:::'
7. Edit 'etc/rc.local', insert telnetd command before 'exit 0':
( sleep 3s; telnetd; ) &
8. Repack the configuration:
tar -zc etc/ | openssl aes-256-cbc -pbkdf2 -k "$decpwd" -out cfg_export_config_file.conf
* If you find an error about 'etc/wireless/mediatek/DBDC_card0.dat',
just ignore it.
9. Upload new configuration via web interface, now you can connect to
CMCC RAX3000Me via telnet.
(Big thanks to https://github.com/lyq1996 who reverse engineered the encryption method)
Check flash type:
If '/dev/mmcblk0' exists on the device, it's eMMC version.
If '/dev/mtd0' exists on the device, it's NAND version.
eMMC Flash instructions:
1. Connect to RAX3000Me, and backup everything, especially 'factory' part.
('data' partition can be ignored, it's useless.)
2. Write new GPT table:
dd if=immortalwrt-mediatek-filogic-cmcc_rax3000me-emmc-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync
3. Write new BL2:
echo 0 > /sys/block/mmcblk0boot0/force_ro
dd if=immortalwrt-mediatek-filogic-cmcc_rax3000me-emmc-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync
4. Write new FIP:
dd if=immortalwrt-mediatek-filogic-cmcc_rax3000me-emmc-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync
5. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
6. Serve ImmortalWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After ImmortalWrt has booted, perform sysupgrade.
NAND Flash instructions:
1. Connect to RAX3000Me, and backup everything, especially 'Factory' part.
2. Write new BL2 and FIP:
If your device HAS USB port, run:
mtd write immortalwrt-mediatek-filogic-cmcc_rax3000me-nand-ddr3-preloader.bin BL2
mtd write immortalwrt-mediatek-filogic-cmcc_rax3000me-nand-ddr3-bl31-uboot.fip FIP
If your device DOES NOT have USB port, run:
mtd write immortalwrt-mediatek-filogic-cmcc_rax3000me-nand-ddr4-preloader.bin BL2
mtd write immortalwrt-mediatek-filogic-cmcc_rax3000me-nand-ddr4-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve ImmortalWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After ImmortalWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 57f31cd5b11cb7e590c330845ec74ffa2d6eb13e)
I selected one subtarget after the other and refreshed their
configuration using this command:
make kernel_oldconfig CONFIG_TARGET=subtarget
For MT7629 I had to re-add CONFIG_LEDS_SMARTRG_LED manually.
Otherwise, building MT7629 with ALL_KMODS we get prompted for
LEDS_SMARTRG_LED and this will break CI and in future buildbot
compilation. See commit 6bdea8c7bd ("mediatek: mt7629: 6.6: disable
LEDS_SMARTRG_LED by default") for more details.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://github.com/openwrt/openwrt/pull/18182
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 5013efc4f907550fadbf15e2fb1bdb2ead3325db)
Prior to commit 8a7d12d674,
cdc-ethernet USB LTE modems (e.g. Quectel EC200A) were consistently named
usb0. After 8a7d12d67, devices began renaming to eth1 due to an assumption
that local MAC addresses originate exclusively from the kernel. Some
devices provide driver-assigned local MACs, causing point-to-point
interfaces with driver-set MACs to adopt eth%d names instead of usb%d.
Restore the naming exception for point-to-point devices: interfaces
without driver MACs or with driver-provided local MACs will retain the
usb%d convention. This addresses issues reported in [1] and fixed in [2].
[1] https://lore.kernel.org/all/Z00udyMgW6XnAw6h@atmark-techno.com/
[2] https://lore.kernel.org/all/20241203130457.904325-1-asmadeus@codewreck.org/
Tested-by: Ahmed Naseef <naseefkm@gmail.com>
Signed-off-by: Ahmed Naseef <naseefkm@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17757
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit ecd609f509f29ed1f75db5c7a623f359c64efb72)
`ucv_array_set` releases the array's reference to the object being cleared.
If this is the last reference to the object, it will be freed, making our
pointer `val` invalid.
To avoid this, we need to obtain our own reference to the object so we
can safely return `val`.
Signed-off-by: Matthew Cather <mattbob4@gmail.com>
(cherry picked from commit 6a10da2934441a59283394a84917edf4983e3043)
Since `wpa_ucode_registry_add` collects its own reference to the values added, the
two functions `hostapd_ucode_bss_get_uval` and `hostapd_ucode_iface_get_uval` would
sometimes return a referenced object (from `uc_resource_new`) and sometimes return
an unreferenced object (from `wpa_ucode_registry_get`). Now, both functions always
return a referenced object.
This change also indirectly fixes `hostapd_ucode_bss_get_uval`, ensuring it now
always returns a referenced object.
Signed-off-by: Matthew Cather <mattbob4@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 7729f960933a03c9eebd2b65a695ea57718ccb77)
Remove extra ucv_get calls when passing a referenced value to an object
without using it further.
Signed-off-by: Matthew Cather <mattbob4@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 22eaf1864731dd29918357b26565dbd9420fd314)
This fixes a common reference counting bug typically along the lines of:
```
uc_value_push(ucv_get(ucv_string_new(...)));
```
This would leave our new string with a reference count of 2, one from
the construction of the string, the other from `ucv_get`. This would
prevent the strings from being correctly cleaned up when it goes out
of scope.
Signed-off-by: Matthew Cather <mattbob4@gmail.com>
(cherry picked from commit f79968ee0f76c41414fb0c08980b9c2a259964d3)
When a feed has submodules, all its submodules are fully cloned whereas
the feed itself is shallowed. Let's be consistent and perform shallow clones
as well for the submodules.
Signed-off-by: Cedric CHEDALEUX <cedric.chedaleux@orange.com>
Link: https://github.com/openwrt/openwrt/pull/18003
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 9ec32cfb2733856a2ab4caee07d9b3297568381d)
When a feed is referenced with a specific commit (i.e. <git_url>^<sha1>),
a full clone was performed and a branch was created from the sha1
and named with the sha1. Other git clones operations are shallowed.
As Git does not support clone at a specific commit, let's first perform
a shallow clone to latest commit, then fetch the relevant commit and
finally checkout it (no more 'pseudo' branch).
It saves bandwith and significantly speeds up the feed update process.
Signed-off-by: Cedric CHEDALEUX <cedric.chedaleux@orange.com>
Link: https://github.com/openwrt/openwrt/pull/18003
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 32d0a57dc10811a24816e51f10e55963f40fe462)
kmod-mmc-mtk does not work well on this board, switch back to deprecated
kmod-sdhci-mt7620 driver for now.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
75a236be122a service: add missing null pointer check
f5341f327539 ubus: add api for generating and validating security tokens
3fab99eab4d5 add udebug support
28d86bd30e97 pex: only respond to update requests when we have network data
8e6f37cc361e pex-msg: ignore no-data responses if version is zero
12e6cf7f63e1 pex: create pex host from update responses
edc8fdae463a ubus: show the local addresses in network status
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit ce68f61cb67a4701a108f838f510e72ca63ed78e)
ethtool since version 6.9 introduced support for getting/setting RSS
input transformation supported in Linux since version 6.8.
The now changed kernel ioctl ABI, however, cannot be detected from
userland, and ethtool since version 6.9 simply assumes that a previously
reserved field is now used to set the input transformation.
Unfortunately the default value RXH_XFRM_NO_CHANGE (0xff) used by ethtool
userland creates an incompatibility with older kernels which cannot be
resolved easily without introducing even more ABI breakage.
Work-around the issue and fix support for --set-rxfh and --set-rxfh-indir
ethtool userland tool commands by making the support for input_xfrm
conditional on compile time, and keep it disabled for Linux 6.6.
Fixes: 8c2dcd1518 ("ethtool: update to 6.10")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Stijn Segers <foss@volatilesystems.org>
(cherry picked from commit 3a7467ffde413677de5465dde78a62dfa8d6774f)
Version 6.11 - October 8, 2024
* Feature: cmis: print active and inactive firmware versions
* Feature: flash transceiver module firmware (--flash-module-firmware)
* Feature: add T1BRR 10Mb/s mode to link mode tables
* Feature: support for disabling netlink from command line
* Fix: fix lanes parameter format specifier
* Fix: add missing clause 33 PSE manual description
* Fix: qsf: Better handling of Page A2h netlink read failure
* Fix: rss: retrieve ring count using ETHTOOL_GRXRINGS ioctl (-x)
* Misc: man page formatting fix
* changelog here: https://git.kernel.org/pub/scm/network/ethtool/ethtool.git/commit/NEWS?id=c0ea4b70c71334ef038f7a3416b228a50dada406
Tested on gl.inet MT6000, retrieve ring count is now working
Signed-off-by: Andrea Pesaresi <andreapesaresi82@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17607
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 9454331b7fc896704a2c60b28767c282eb9ca0bd)
