Backport FORESEE NAND chip support from upstream Linux. The newly
introduced FORESEE F35SQA001G was found on the Xiaomi AX3000T.
Signed-off-by: Erik Servili <serverror@serverror.com>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit 302c717aa3)
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 64GB eMMC or 128 MB SPI-NAND
RAM: 512MB DDR3 or DDR4
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
Gain SSH access:
1. Login into web interface, and download the configuration.
2. Get the SN of the device from web interface or the label on the back of the device.
3. Calculate configuration decryption password:
Command "eval" is necessary here as the encryption implentation treats '$...' as (empty) variables.
decpwd="$(eval echo $(openssl passwd -1 -salt aV6dW8bD "your_device_sn"))"
4. Decrypt the configuration:
openssl aes-256-cbc -d -pbkdf2 -k "$decpwd" -in cfg_export_config_file.conf -out cfg_export_config_file.conf.dec
5. Enter fakeroot, decompress the configuration:
tar -zxf cfg_export_config_file.conf.dec
6. Edit 'etc/shadow', update (remove) root password: 'root::19179:0:99999:7:::'
7. Edit 'etc/rc.local', insert telnetd command before 'exit 0':
( sleep 3s; telnetd; ) &
8. Repack the configuration:
tar -zc etc/ | openssl aes-256-cbc -pbkdf2 -k "$decpwd" -out cfg_export_config_file.conf
* If you find an error about 'etc/wireless/mediatek/DBDC_card0.dat',
just ignore it.
9. Upload new configuration via web interface, now you can connect to
CMCC RAX3000Me via telnet.
(Big thanks to https://github.com/lyq1996 who reverse engineered the encryption method)
Check flash type:
If '/dev/mmcblk0' exists on the device, it's eMMC version.
If '/dev/mtd0' exists on the device, it's NAND version.
eMMC Flash instructions:
1. Connect to RAX3000Me, and backup everything, especially 'factory' part.
('data' partition can be ignored, it's useless.)
2. Write new GPT table:
dd if=immortalwrt-mediatek-filogic-cmcc_rax3000me-emmc-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync
3. Write new BL2:
echo 0 > /sys/block/mmcblk0boot0/force_ro
dd if=immortalwrt-mediatek-filogic-cmcc_rax3000me-emmc-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync
4. Write new FIP:
dd if=immortalwrt-mediatek-filogic-cmcc_rax3000me-emmc-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync
5. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
6. Serve ImmortalWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After ImmortalWrt has booted, perform sysupgrade.
NAND Flash instructions:
1. Connect to RAX3000Me, and backup everything, especially 'Factory' part.
2. Write new BL2 and FIP:
If your device HAS USB port, run:
mtd write immortalwrt-mediatek-filogic-cmcc_rax3000me-nand-ddr3-preloader.bin BL2
mtd write immortalwrt-mediatek-filogic-cmcc_rax3000me-nand-ddr3-bl31-uboot.fip FIP
If your device DOES NOT have USB port, run:
mtd write immortalwrt-mediatek-filogic-cmcc_rax3000me-nand-ddr4-preloader.bin BL2
mtd write immortalwrt-mediatek-filogic-cmcc_rax3000me-nand-ddr4-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve ImmortalWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After ImmortalWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 57f31cd5b11cb7e590c330845ec74ffa2d6eb13e)
`ucv_array_set` releases the array's reference to the object being cleared.
If this is the last reference to the object, it will be freed, making our
pointer `val` invalid.
To avoid this, we need to obtain our own reference to the object so we
can safely return `val`.
Signed-off-by: Matthew Cather <mattbob4@gmail.com>
(cherry picked from commit 6a10da2934441a59283394a84917edf4983e3043)
Since `wpa_ucode_registry_add` collects its own reference to the values added, the
two functions `hostapd_ucode_bss_get_uval` and `hostapd_ucode_iface_get_uval` would
sometimes return a referenced object (from `uc_resource_new`) and sometimes return
an unreferenced object (from `wpa_ucode_registry_get`). Now, both functions always
return a referenced object.
This change also indirectly fixes `hostapd_ucode_bss_get_uval`, ensuring it now
always returns a referenced object.
Signed-off-by: Matthew Cather <mattbob4@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 7729f960933a03c9eebd2b65a695ea57718ccb77)
Remove extra ucv_get calls when passing a referenced value to an object
without using it further.
Signed-off-by: Matthew Cather <mattbob4@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 22eaf1864731dd29918357b26565dbd9420fd314)
This fixes a common reference counting bug typically along the lines of:
```
uc_value_push(ucv_get(ucv_string_new(...)));
```
This would leave our new string with a reference count of 2, one from
the construction of the string, the other from `ucv_get`. This would
prevent the strings from being correctly cleaned up when it goes out
of scope.
Signed-off-by: Matthew Cather <mattbob4@gmail.com>
(cherry picked from commit f79968ee0f76c41414fb0c08980b9c2a259964d3)
75a236be122a service: add missing null pointer check
f5341f327539 ubus: add api for generating and validating security tokens
3fab99eab4d5 add udebug support
28d86bd30e97 pex: only respond to update requests when we have network data
8e6f37cc361e pex-msg: ignore no-data responses if version is zero
12e6cf7f63e1 pex: create pex host from update responses
edc8fdae463a ubus: show the local addresses in network status
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit ce68f61cb67a4701a108f838f510e72ca63ed78e)
ethtool since version 6.9 introduced support for getting/setting RSS
input transformation supported in Linux since version 6.8.
The now changed kernel ioctl ABI, however, cannot be detected from
userland, and ethtool since version 6.9 simply assumes that a previously
reserved field is now used to set the input transformation.
Unfortunately the default value RXH_XFRM_NO_CHANGE (0xff) used by ethtool
userland creates an incompatibility with older kernels which cannot be
resolved easily without introducing even more ABI breakage.
Work-around the issue and fix support for --set-rxfh and --set-rxfh-indir
ethtool userland tool commands by making the support for input_xfrm
conditional on compile time, and keep it disabled for Linux 6.6.
Fixes: 8c2dcd1518 ("ethtool: update to 6.10")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Stijn Segers <foss@volatilesystems.org>
(cherry picked from commit 3a7467ffde)
Version 6.11 - October 8, 2024
* Feature: cmis: print active and inactive firmware versions
* Feature: flash transceiver module firmware (--flash-module-firmware)
* Feature: add T1BRR 10Mb/s mode to link mode tables
* Feature: support for disabling netlink from command line
* Fix: fix lanes parameter format specifier
* Fix: add missing clause 33 PSE manual description
* Fix: qsf: Better handling of Page A2h netlink read failure
* Fix: rss: retrieve ring count using ETHTOOL_GRXRINGS ioctl (-x)
* Misc: man page formatting fix
* changelog here: https://git.kernel.org/pub/scm/network/ethtool/ethtool.git/commit/NEWS?id=c0ea4b70c71334ef038f7a3416b228a50dada406
Tested on gl.inet MT6000, retrieve ring count is now working
Signed-off-by: Andrea Pesaresi <andreapesaresi82@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17607
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 9454331b7f)
This board is also as known as SuperElectron ZN-M5 and ZN-M8. However,
for ZN-M5 and ZN-M8, there's another version uses ZX279128 as CPU
chip, which is unsupported.
You can check it in "高级设置" > "系统日志" > "内核日志" page from webUI.
Stock layout flash instructions:
Login into webUI and upload sysupgrade firmware in "系统管理" > "升级固件" page.
Remember to unselect "保留配置" ("Keep configurations") first before doing that.
OpenWrt U-Boot layout flash instructions:
1. Flash stock layout firmware first.
2. Connect to the device via SSH, and backup everything,
especially 'Factory' partition.
3. Unlock MTD partitions:
apk update && apk add kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
4. Write new BL2 and FIP:
mtd write immortalwrt-mediatek-filogic-cmcc_a10-ubootmod-preloader.bin BL2
mtd write immortalwrt-mediatek-filogic-cmcc_a10-ubootmod-bl31-uboot.fip FIP
5. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
6. Serve ImmortalWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After ImmortalWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 4e9240e733)
Changes between 3.0.15 and 3.0.16 [11 Feb 2025]
CVE-2024-13176[1] - Fixed timing side-channel in ECDSA signature
computation.
There is a timing signal of around 300 nanoseconds when the top word of
the inverted ECDSA nonce value is zero. This can happen with significant
probability only for some of the supported elliptic curves. In
particular the NIST P-521 curve is affected. To be able to measure this
leak, the attacker process must either be located in the same physical
computer or must have a very fast network connection with low latency.
CVE-2024-9143[2] - Fixed possible OOB memory access with invalid
low-level GF(2^m) elliptic curve parameters.
Use of the low-level GF(2^m) elliptic curve APIs with untrusted explicit
values for the field polynomial can lead to out-of-bounds memory reads
or writes. Applications working with "exotic" explicit binary (GF(2^m))
curve parameters, that make it possible to represent invalid field
polynomials with a zero constant term, via the above or similar APIs,
may terminate abruptly as a result of reading or writing outside of
array bounds. Remote code execution cannot easily be ruled out.
1. https://www.openssl.org/news/vulnerabilities.html#CVE-2024-13176
2. https://www.openssl.org/news/vulnerabilities.html#CVE-2024-9143
Build system: x86/64
Build-tested: bcm27xx/bcm2712
Run-tested: bcm27xx/bcm2712
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/17947
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit b4e6fd7b76)
b43aeb5 wireless-regdb: assert and correct maximum bandwidth within frequency difference
68588bf wireless-regdb: Update regulatory info for Syria (SY) for 2020
0dda57e wireless-regdb: Update regulatory info for Moldova (MD) on 6GHz for 2022
b19ab0b wireless-regdb: Update regulatory info for Azerbaijan (AZ) on 6GHz for 2024
f67f40d wireless-regdb: Update regulatory info for Oman (OM)
bd70876 wireless-regdb: Update regulatory rules for Armenia (AM) on 2.4 and 5 GHz
6c7cbcc wireless-regdb: Permit 320 MHz bandwidth in 6 GHz band in ETSI/CEPT
f9f6b30 wireless-regdb: Update regulatory rules for Austria (AT)
39b47ea wireless-regdb: Update regulatory info for Cayman Islands (KY) for 2024
3dd7ceb wireless-regdb: allow NO-INDOOR flag in db.txt
4d754a1 wireless-regdb: Update regulatory rules for Iran (IR) on both 2.4 and 5Ghz for 2021
8c8308a wireless-regdb: Update frequency range with NO-INDOOR for Oman (OM)
c2f11e2 wireless-regdb: update regulatory database based on preceding changes
Signed-off-by: Rudy Andram <rmandrad@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17957
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit da2cc98458)
It will require too much effort to make the driver work in kernel 6.6.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit d04b0cbe39)
Depending on the config / circumstances, the get_psk call can be called
multiple times from differnt places, which can lead to wrong sta->psk_idx
values. The correct call is the one that is also interested in the vlan_id,
so use the vlan_id pointer as indication of when to set sta->psk_idx.
Also fix off-by-one error for secondary PSKs
Fixes: b2a2c28617 ("hostapd: add support for authenticating with multiple PSKs via ubus helper")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 8118b2dace)
The 00 address_mask needs to be inverted, otherwise the mac address
allocation will modify the last byte instead of the first one.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 1ee44825ad)
93458ac dns: fix response to TYPE_PTR query
68af311 fix unicast response port and timeout
a2b4979 service: announce all services in single dns answer
4537734 display announced services in ubus call umdns browse
0b50c29 display more srv attributes in output of ubus browse function
Signed-off-by: John Crispin <john@phrozen.org>
(cherry picked from commit d162fd5ed4)
322500403615 service: add default group @ to match all nodes
5f7860306200 ubus: rename unetd_ubus_notify to unetd_ubus_network_notify
d13752814651 enroll: add PEX sub-protocol to support enrolling new nodes into a network
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit c0f06cb6ac)
47b54cf5a4b6 types: introduce `ucv_array_sort_r()` and `ucv_object_sort_r()`
efeb57806552 types, vm: refactor usage of global variables
f9d2faf67de6 vm: reset signals when freeing VM
4e86847d802d lib: utilize `ucv_array_sort_r()` and `ucv_object_sort_r()`
c71444ea301f types: ucv_resource_create(): rename `typename` parameter to `type`
373df7299c79 nl80211: properly support split_wiphy_dump for single phys
9bcd25f54708 lexer: Preserve keyword, regexp flags until processing non-comment tokens
0a7ff4715cb8 main: pretty-print `-p` output by default
4c3d5b469156 struct: Add new buffer API for incremental packing/unpacking
efc4122124cb struct: do not use global variables for caching types
Fixes: https://github.com/jow-/ucode/issues/248
Fixes: https://github.com/jow-/ucode/issues/250
Fixes: https://github.com/efahl/owut/issues/25
Link: https://github.com/openwrt/openwrt/pull/17191
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit af6f1a90bb)
b0b5d93 Merge pull request #234 from IdWV/fs
60e7a88 Merge pull request #232 from sebastianertz/lib-digest
1752779 digest: implement compile time option to exclude less common algorithms
c7268a1 ci: include libmd in MacOS CI builds
fcb6f70 lib: introduce digest library
1323a27 Merge pull request #246 from jow-/fix-upvalue-resolve
ed5ce8f types: resolve upvalue values in arrays and objects
a6e0641 vm: resolve upvalues before pushing them onto the stack
ef1baab ci: drop OpenWrt tests for now
63e18ea fs: eliminate the usage of global variables
b1bd7b5 types: add ucv_resource_create() helper
3408edf Merge pull request #244 from nbd168/nl80211
8af77e7 nl80211: add new attributes for multi-radio support
1423ad7 nl80211: cover extended feature and EHT rate info attributes
ee1d6d8 Merge pull request #237 from sebastianertz/math
4b18a9b Merge pull request #213 from jow-/improve-vector-macros
1f022c0 math: removed global variable for thread safety
e5fe6b1 treewide: refactor vector usage code
20307ee utils: improve vector utilities
aa18952 Merge pull request #241 from jow-/socket-local-fanout-decl
79ccd9c socket: provide local definition of `struct fanout_args`
402280d Merge pull request #239 from jow-/safe-insert-during-obj-iteration
07afe96 Merge pull request #240 from jow-/stricter-number-conversion
736d450 types: fix potential use after free on adding keys during iteration
4134e71 vallist: more thoroughly check for trailing garbage after numeric string
9cf53dd Merge pull request #226 from jow-/lexer-improvements
2b2e732 lexer: make api functions public
855854f lexer: emit comment and template statement block tokens
328a50f lexer: improve token position reporting
fa22732 Merge pull request #225 from jow-/compiler-fix-keyword-property-labels-after-spread
6e88c62 Merge pull request #224 from jow-/lib-fs-readline-leak
94d1211 compiler: properly treat property names after spread expressions
67cd123 fs: fix potential memory leak on i/o errors in .read()
Signed-off-by: John Crispin <john@phrozen.org>
(cherry picked from commit ba9cdbeea8)
Makes it easier to enable MDNS on wan without having to edit the firewall
configuration for it
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 05138fe898)
Unless another toolchain is present (or selected), build the bpf toolchain
whenever a package is selected that needs it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 6605e45676)
