When support for Routerboard 911G was introduced, Routerboad 912UAG
device tree was used as a base, and the common part. This led to use of
40MHz as the reference clock frequency for both [1], while RB911G uses 25MHz
crystal on the board, causing heavy system clock drift.
Split the definition, and set the reference clock frequency for RB911G
back to 25MHz.
[1] a716ac5564 ("ath79: fix reference clock for RouterBoard 912UAG")
Fixes: bcc44b1212 ("ath79: support for MikroTik RouterBOARD 911G-(2,5)HPnD")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17944
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 40fc6bd5cc)
It's no longer able to generate images for devices with limited flash
(<= 8 MiB), so just use the full feature wpad.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Now, that initramfs images built for ZTE devices work, by moving
LZMA_TEXT_START further up the available RAM - same fix works
successfully for Meraki MR18 too. Apply it and reenable initramfs
generation again.
Fixes: 1d49310fdb ("ath79: add Cisco Meraki MR18")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17680
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 7423e67e1b)
initramfs for some devices grew so big, that it can't be loaded within
the previous 32MB RAM limit. Make the LZMA_TEXT_ADDRESS configurable
per-target once again, to fix it for bigger devices, while maintaining
compatibility with previous ones.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17616
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 6720958659)
According to datasheet, on AR9344 the switch and switch analog need to
be reset first before initiating a full reset.
Resetting these systems fixes spurious reset hangs on Atheros AR9344
SoCs.
Link: https://github.com/freifunk-gluon/gluon/issues/2904
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 144af32b47)
This reverts commit 916af73fc3.
It was reported this change did not fix the reboot issues on AR9344.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 937b5a3e00)
Due to "SIM present" input defaulting to "button" type, it is
interpreted as such when booting, and causes the system to enter
failsafe, if the tray is missing. Similarly to rfkill switch on
TP-Link WDR4300 and Archer C7, make it EV_SW instead, to stop it from
interfering with the boot process.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17503
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 7b9ca01109)
According to datasheet, on AR9344 the switch and switch analog need to
be reset first before initiating a full reset.
Resetting these systems fixes spurious reset hangs on Atheros AR9344
SoCs.
Link: https://github.com/freifunk-gluon/gluon/issues/2904
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 916af73fc3)
Referencing commit a1837135e0
Hardware
--------
SoC: Qualcomm Atheros QCA9558
RAM: 128M DDR2 (Nanya NT5TU64M16HG-AC)
FLASH: 128M SPI-NAND (Spansion S34ML01G100TFI00)
WLAN: QCA9558 3T3R 802.11 bgn
ETH: Qualcomm Atheros QCA8337
UART: 115200 8n1
BUTTON: Reset - WPS - "Router" switch
LED: 2x system-LED, 2x wlan-LED, 1x internet-LED,
2x routing-LED
LEDs besides the ethernet ports are controlled
by the ethernet switch
MAC Address:
use address(sample 1) source
label cc:e1:d5:xx:xx:ed art@macaddr_wan
lan cc:e1:d5:xx:xx:ec art@macaddr_lan
wan cc:e1:d5:xx:xx:ed $label
WiFi4_2G cc:e1:d5:xx:xx:ec art@cal_ath9k
Installation from Serial Console
------------
1. Connect to the serial console. Power up the device and interrupt
autoboot when prompted
2. Connect a TFTP server reachable at 192.168.11.10/24
to the ethernet port. Serve the OpenWrt initramfs image as
"openwrt.bin"
3. Boot the initramfs image using U-Boot
ath> tftpboot 0x84000000 openwrt.bin
ath> bootm 0x84000000
4. Copy the OpenWrt sysupgrade image to the device using scp and
install it like a normal upgrade (with no need to keeping config
since no config from "previous OpenWRT installation" could be kept
at all)
# sysupgrade -n /path/to/openwrt/sysupgrade.bin
Installation from Web Interface
------------
To flash just do a firmware upgrade from the stock firmware (Buffalo
branded dd-wrt) with squashfs-factory.bin
Signed-off-by: Edward Chow <equu@openmail.cc>
Link: https://github.com/openwrt/openwrt/pull/17227
(cherry picked from commit 42254d3f5f)
Link: https://github.com/openwrt/openwrt/pull/17359
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The KuWFi N650 is a 5GHz outdoor wireless bridge based on QCA9563.
Specs
=====
CPU: QCA9563, 775MHz
RAM: 128MiB
Flash: 16MiB
Wireless: QCA9888 (5GHz only)
Ethernet: 2x GBit (via QCA8337), 48V passive PoE
Installation
============
From OEM firmware
-----------------
The OEM firmware has telnet enabled by default. If not, it can be enabled
from the firmware web interface. You need a TFTP server on your computer
and the OpenWrt factory image should be available as "n650factory.bin".
It is assumed that your computer has the IP 192.168.1.1 and the N650
192.168.1.20 (default IP address).
1. Connect via Telnet to the device and log in with the default credentials
"admin:admin"
2. Exploit the limited interface by typing "ps & /bin/sh"
3. Press <ENTER> to start the shell
4. Enter the following commands:
$ cd /tmp
$ tftp -r n650factory.bin -g 192.168.1.1
$ cat << EOF > /tmp/openwrt.sh
IMAGE_NAME="\$1"
if [ ! -e \${IMAGE_NAME} ]; then
echo "Image file not found: \${IMAGE_NAME}"
exit 1
fi
. /usr/sbin/common.sh
kill_remaining TERM
sleep 3
kill_remaining KILL
run_ramfs mtd write \${IMAGE_NAME} firmware
sleep 2
reboot -f
EOF
$ chmod +x /tmp/openwrt.sh
$ /tmp/openwrt.sh n650factory.bin
Once the device reboots, it should load OpenWrt.
From UART
---------
UART installation is possible since the serial header is already soldered
on. The pinout is GND - Tx - Rx - VCC from top to bottom (RJ45 ports are
at the bottom). Connect with 115200 8N1.
First, boot OpenWrt from TFTP. Enter the following commands in the U-Boot
shell, assuming your computer has the IP address 192.168.1.1 and a TFTP
server running where the initramfs image is provided as n650.bin:
setenv ipaddr 192.168.1.20
setenv serverip 192.168.1.1
tftpboot 0x84000000 n650.bin
bootm
Once booted, transfer -loader.bin and -sysupgrade.bin images to the device
at /tmp. Enter the following commands, replacing the filenames:
mtd write /tmp/loader.bin loader
sysupgrade /tmp/sysupgrade.bin
Reboot and OpenWrt should load from flash.
Back to Stock
-------------
Back to stock is only possible if you saved a partition backup before
installing OpenWrt. Assuming you have fullbackup.bin covering the whole
flash, you need to prepare the image as follows:
$ dd if=fullbackup.bin of=fwconcat0.bin bs=65536 skip=4 count=212
$ dd if=fullbackup.bin of=loader.bin bs=65536 skip=216 count=1
$ dd if=fullbackup.bin of=fwconcat1.bin bs=65536 skip=217 count=22
$ cat fwconcat0.bin fwconcat1.bin > firmware.bin
Transfer firmware.bin and loader.bin to the OpenWrt device. First, flash
loader.bin to mtd device loader, then force sysupgrade:
$ mtd write loader.bin loader
$ sysupgrade -F firmware.bin
The reason for the two-step process is the way the flash layout is designed
for OpenWrt in contrast to the OEM firmware partition.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Link: https://github.com/openwrt/openwrt/pull/17089
Link: https://github.com/openwrt/openwrt/pull/17247
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit dde510cf97)
This reverts commit 70e41d0205.
"ethaddr" is stored into the "u-boot-env" (stock: "Config") partition
and it's quoted with double-quotations, but that format is not supported
by the current NVMEM u-boot-env driver (and mac_pton() function) and the
MAC address won't be parsed to byte array.
This causes random MAC addresses on the adapters, so revert the above
commit.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17116
(cherry picked from commit af611bce44)
Link: https://github.com/openwrt/openwrt/pull/17117
Signed-off-by: Robert Marko <robimarko@gmail.com>
TP-Link CPE710-v2 is an outdoor wireless CPE for 5 GHz with one Ethernet
port based on the AP152 reference board. Compared to the CPE710-v1, the
only change observed in hardware is that the mdio address of the ethernet
physical changed from 0x4 to 0x0.
Specifications:
- SoC: QCA9563-AL3A MIPS 74kc @ 775MHz, AHB @ 258MHz
- RAM: 128MiB DDR2 @ 650MHz
- Flash: 16MiB SPI NOR Based on the GD25Q128
- Wi-Fi 5Ghz: ath10k chip (802.11ac for up to 867Mbps on 5GHz wireless
data rate), based on the QCA9896
- Ethernet: one 1GbE port
- 23dBi high-gain directional 2×2 MIMO parabolic antenna
- Power, LAN, WLAN5G Blue LEDs
Flashing instructions:
Flash factory image through stock firmware WEB UI or through TFTP
To get to TFTP recovery just hold reset button while powering on for around
30-40 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254
Signed-off-by: Tim Noack <tim@noack.id>
Link: https://github.com/openwrt/openwrt/pull/16637
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 5572e0196a)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The Sophos AP15C uses the same hardware as the AP15, but has a reset button.
Based on:
commit 6f1efb2898 ("ath79: add support for Sophos AP100/AP55 family")
author Andrew Powers-Holmes <andrew@omnom.net>
Fri, 3 Sep 2021 15:53:57 +0200 (23:53 +1000)
committer Hauke Mehrtens <hauke@hauke-m.de>
Sat, 16 Apr 2022 16:59:29 +0200 (16:59 +0200)
Unique to AP15C:
- Reset button
- External RJ45 serial console port
Flashing instructions:
This firmware can be flashed either via a compatible Sophos SG or XG
firewall appliance, which does not require disassembling the device, or via
the U-Boot console available on the internal UART header.
To flash via XG appliance:
- Register on Sophos' website for a no-cost Home Use XG firewall license
- Download and install the XG software on a compatible PC or virtual
machine, complete initial appliance setup, and enable SSH console access
- Connect the target AP device to the XG appliance's LAN interface
- Approve the AP from the XG Web UI and wait until it shows as Active
(this can take 3-5 minutes)
- Connect to the XG appliance over SSH and access the Advanced Console
(Menu option 5, then menu option 3)
- Run `sudo awetool` and select the menu option to connect to an AP via
SSH. When prompted to enable SSH on the target AP, select Yes.
- Wait 2-3 minutes, then select the AP from the awetool menu again. This
will connect you to a root shell on the target AP.
- Copy the firmware to /tmp/openwrt.bin on the target AP via SCP/TFTP/etc
- Run `mtd -r write /tmp/openwrt.bin astaro_image`
- When complete, the access point will reboot to OpenWRT.
To flash via U-Boot serial console:
- Configure a TFTP server on your PC, and set IP address 192.168.99.8 with
netmask 255.255.255.0
- Copy the firmware .bin to the TFTP server and rename to 'uImage_AP15C'
- Open the target AP's enclosure and locate the 4-pin 3.3V UART header [4]
- Connect the AP ethernet to your PC's ethernet port
- Connect a terminal to the UART at 115200 8/N/1 as usual
- Power on the AP and press a key to cancel autoboot when prompted
- Run the following commands at the U-Boot console:
- `tftpboot`
- `cp.b $fileaddr 0x9f070000 $filesize`
- `boot`
- The access point will boot to OpenWRT.
Signed-off-by: David Lutz <kpanic@hirnduenger.de>
(cherry picked from commit a7abc7ec3b)
The last "syscfg" partition of the OEM firmware turns out to be a
UBIFS used to store user data, just as the "rootfs_data" of OpenWrt,
so it should be reasonable to absorb it into the "ubi" partition.
Factory installations via either OEM firmware or tftp, or by forcibly
flashing factory image to mtd5 (firmware) partition with mtd tool are
confirmed working, but the UBI remaining inside "syscfg" partition
could break upgrade. Fortunately, installing kmod-mtd-rw and erasing
"syscfg" partition before upgrade is confirmed working, in which case,
"ubi" will automatically expand to the blank space once occupied by
the former mtd8 (syscfg), with the total block number increased, but
the UBIFS for rootfs_data will not automatically claim the newly
available space (since it is created when mtd8 still exists, and
sysupgrade does not set "autoresize" flag to rootfs_data). These space
will be claimed during the next upgrade, when rootfs_data is removed
and created again.
Fixes: 50f727b773 ("ath79: add support for Linksys EA4500 v3")
Signed-off-by: Edward Chow <equu@openmail.cc>
Link: https://github.com/openwrt/openwrt/pull/14791
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix in commit 25eead21c5 ("ath79: fix 5GHz on QCA9886 variant of ZTE MF286")
was incomplete. A user of such variant popped up, and in the boot log
after installation, we discovered that QCA9886 expects different
pre-calibration data size, than the older QCA9880 variant:
ath10k_pci 0000:00:00.0: qca9888 hw2.0 target 0x01000000 chip_id 0x00000000 sub 0000:0000
ath10k_pci 0000:00:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
ath10k_pci 0000:00:00.0: firmware ver 10.4b-ct-9888-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 59e741e7
ath10k_pci 0000:00:00.0: invalid calibration data length in nvmem-cell 'pre-calibration': 2116 != 12064
ath10k_pci 0000:00:00.0: Loading BDF type 0
ath10k_pci 0000:00:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0056,subsystem-vendor=0000,subsystem-device=0000 from ath10k/QCA9888/hw2.0/board-2.bin
ath10k_pci 0000:00:00.0: failed to fetch board-2.bin or board.bin from ath10k/QCA9888/hw2.0
ath10k_pci 0000:00:00.0: failed to fetch board file: -12
ath10k_pci 0000:00:00.0: could not probe fw (-12)
Explicitly define a pre-calibration nvmem-cell for this variant, and use
it instead of the calibration one, which is shorter.
Fixes: 25eead21c5 ("ath79: fix 5GHz on QCA9886 variant of ZTE MF286")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16809
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
