Brings lots of driver updates and API changes needed for mt76 updates.
Disable iwlwifi and ath11k on 5.15, since backport is too difficult,
and the only remaining targets won't need those drivers.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This reverts commit dc9c5d1ee7.
Additional file for ath10k-ct slipped in, revert for a better version
pushed later.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
LEDs support for ath10k has finally merged upstream hence replace it
with the upstream version.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This adds support for the RTL8723BE PCIe Wi-Fi Adapter by adding backports drivers
Signed-off-by: David Adriao <davidadriao@dglitch.com>
[Do not remove rtl8xxxu and add dependency to rtl8723be-firmware]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It seems that move to kernel 6.6 somehow fixed the remoteproc restart so
now it properly restarts and thus coldboot calibration works as well.
ipq60xx still seems to be broken in a different way so keep it disabled.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Limiting allowed channels per device may be required and is commonly
supported on other drivers, so include a pending patch to add support for
the same.
Signed-off-by: Robert Marko <robimarko@gmail.com>
The carl9170_tx_release() function sometimes triggers a fortified-memset
warning in my randconfig builds:
In file included from include/linux/string.h:254,
from drivers/net/wireless/ath/carl9170/tx.c:40:
In function 'fortify_memset_chk',
inlined from 'carl9170_tx_release' at drivers/net/wireless/ath/carl9170/tx.c:283:2,
inlined from 'kref_put' at include/linux/kref.h:65:3,
inlined from 'carl9170_tx_put_skb' at drivers/net/wireless/ath/carl9170/tx.c:342:9:
include/linux/fortify-string.h:493:25: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
493 | __write_overflow_field(p_size_field, size);
Kees previously tried to avoid this by using memset_after(), but it seems
this does not fully address the problem. I noticed that the memset_after()
here is done on a different part of the union (status) than the original
cast was from (rate_driver_data), which may confuse the compiler.
Unfortunately, the memset_after() trick does not work on driver_rates[]
because that is part of an anonymous struct, and I could not get
struct_group() to do this either. Using two separate memset() calls
on the two members does address the warning though.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
The lincense information for the packages mac80211 are missing.
This commit adds the missing information.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Add a separate bit in struct ieee80211_tx_info to indicate airtime tracked
as broadcast/multicast. This avoids a race condition where airtime from
stations that were just removed wasn't getting subtracted from the total
PHY airtime.
Fixes: 95e633efbd ("mac80211: add AQL support for broadcast/multicast packets")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
As the Visionfive V1 board has an Ampak module connected via SDIO, enable
support for SDIO in the brcmfmac module.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
The AQL limit for buffered broadcast packets is higher than the maximum
total pending airtime limit. This can get unicast data stuck whenever there
is too much pending broadcast data. Fix this by excluding broadcast AQL from
the total limit.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
ath25 has been on life support for the last couple of releases, eventually
leading to marking it as source-only in 2023.
It has been basically only touched to do a kernel bump so that we can make
the new OpenWrt release which was a challenge due to small RAM amount.
However, with the attempt of kernel 6.1 update it turns out that kernel
cannot even finish booting due to RAM constraints, so its time to let this
target go.
Signed-off-by: Robert Marko <robimarko@gmail.com>
When both variants of ath10k drivers are selected, any driver that is
selected along is being built twice, one for each ath10k variant.
Avoid these redundant builds by introducing an optional second parameter
to config_package that lists the variants for which the package is to be
built.
If the symbol is to be set for all of the variants, $(ALL_VARIANTS) can
be used. This is the case for the mac80211 and cfg80211 modules. If
the parameter is empty, then the module will be selected and thus built
when the first variant is compiled.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Having different build directories is the default when the package
Makefile defines more than one variant.
Mac80211 overrides PKG_BUILD_DIR, not taking different variants in
consideration, which causes clobbering the directories when both
variants are built.
When compiled with AUTOREMOVE=y, the effect is that the package is
unnecessarily rebuilt when the package is compiled again.
Wihout AUTOREMOVE, the problem is worse: the second variant will not be
rebuilt, and you end up with the smallbuffers variant being a copy of
the regular one.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
