Fix issue with LAN1 interface on ap3935 devices, where the LAN
1interface won't come up after boot unless the bootloader has
initialized the network stack. Use of `fixed-link` in the prior code
kept the driver from clobbering PHY settings, but now that the driver
supports rgmii-id phy-mode, we can just use that.
Signed-off-by: Bryan Berg <bdb@north-eastham.org>
Link: https://github.com/openwrt/openwrt/pull/13629
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix broken line break for Linksys e8350-v1 pushed with CRLF instead of
LF.
Fixes: 45b3c620e5 ("ipq806x: add support for Linksys e8350-v1")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
AC2400 Dual-Band Gigabit Wi-Fi Router base on ipq8064.
https://www.linksys.com/support-product?sku=E8350
Specification:
- Qualcomm dual-core IPQ8064 @ 1.4 GHz
- 512 MB of RAM
- 4 MB of SPI NOR MX25U3235F
- 128 MB of NAND S34MS01G2
- Qualcomm QCA9880 2.4GHz 802.11bgn
- Quantenna QSR1000 5GHz 802.11ac (no support)
- 4 x 10/100/1000 Mbit/s w/ vlan support Ethernet
- Qualcomm Atheros QCA8337 switch
- 1 x 3.0 + 1 x 2.0 (combo with eSata port)
- 115200, 8N1 internal serial console
- Power, Reset, WPS and WLAN buttons
- Power, WPS and WLAN leds
- 12 VDC, 3 A power
Installation:
The installation must be done using web interface of the router.
To achive this new firmware-utils tool was added to set correct
magic headers for the factory images.
Installation from vendor firmware:
1. Flash over the native Linksys WEB interface using factory image.
Installation using recovery mode:
1. Power off the device and disconnect the WAN port.
(Only LAN port to be connected)
2. Press & hold the "Reset" button
3. Power on the device & wait 10 seconds with pressed "Reset" button
4. Set IP Internet Protocol on your PC from
192.168.1.0/24 network (Router is on IP 192.168.1.1)
5. Open the Firmware Recovery page in your browser:
http://192.168.1.1/index.shtml
Firmware Recovery -> File Name -> Recovery & Reboot
The device page in inbox:
https://openwrt.org/inbox/toh/linksys/linksys_ea8350_1
Signed-off-by: Sergey Filippov <sergey.filippov@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/15798
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
All three PCIe ports are reported non working on Meraki MR42/MR52 boards
since kernel 6.1 with the issue of PCIe PHY link never coming up thus
no WLAN cards are available on the boards.
After debugging it seems that PCIe worked on 5.15 and older purely by
accident as device DTS was using /delete-property/ perst-gpios; in each
of the 3 PCIe nodes but there was no "perst-gpios" property in the SoC DTSI
as it was still using the older "perst-gpio" property so it was not getting
removed from the device DTS.
However, in kernel 6.1 commit ("ARM: dts: qcom-*: replace deprecated
perst-gpio with perst-gpios") updated all Qualcomm DTS-es to use the newer
"perst-gpios" and thus once ipq806x moved to 6.1 PCIe stopped working as
now that property was being dropped from the device DTS.
So, since the removal of PERST pins seems to have been wrong from the start
lets drop the property removal from MR42/MR52.
Fixes: #15408
Link: https://github.com/openwrt/openwrt/pull/15509
Signed-off-by: Robert Marko <robimarko@gmail.com>
There is a custom LED controller between the 3 SoC GPIO outputs and
the red and blue LEDs of the device. It implements a strange mapping
that includes fixed, flashing, and breathing modes.
The current DTS configuration causes OpenWrt to flash the LEDs over
the controller's own flashing, resulting in chaotic output in boot,
failsafe, and upgrade modes.
This change fixes the LEDs in the best way possible as long as each
OpenWrt running state is limited to be signaled by a single led.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15440
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Set DEVICE_DTS_DIR to /qcom by default instead of limiting it to
TESTING_KERNEL since we moved 6.6 to default version.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add pending patch fixing nandc with new kerenel due to broken convertion
to new nand API. Patch has been sent upstream and will be backported to
stable kernel if accepted.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Rework kernel patches for new kernel. Mainly adaptation for patch
related to DTS and changes for the downstream div generalize patch that
now use determine_rate.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Since with recent kernel version DTS moved to a dedicated directory,
it's required to split files to per kernel version to follow kernel
version directory structure.
Also makes use of DEVICE_DTS_DIR to target the correct DTS directory
based on the kernel version.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Replace ARM bootloader patch with pending upstream version. The patch
got reviewed upstream and tested on a Netgear R7800.
This fix a problem with the ARM decompressor and permits to use
AUTO_ZRELADDR without having to hardcode PHYS_OFFSET as the bootloader
now correctly parse the memory modes in the appended DTB.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix DTS error in LED color/function conversion due to a bug in the
conversion script.
Fixes: 33e7962329 ("ipq806x: convert to new LED color/function format where possible")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Initial conversion to new LED color/function format
and drop label format where possible. The same label
is composed at runtime.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport at803x split patches merged upstream to tidy things up for the
at803x PHY driver.
New Kernel config are introduced hence any user needs to be updated.
Downstream ipq40xx patch require rework to correctly move them to the
qcom specific PHY directory.
All affected patch automatically refreshed.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
They are unnecessary since ipq806x switched to DSA in
the commit 337e36e0ef.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Reviewed-by: Robert Marko <robimarko@gmail.com>
