The switch to the upstream mmc-mtk driver caused problems with MT7621
because of unstable too high clock frequency:
[ 49.643291] mmc0: error -88 whilst initialising SD card
[ 49.890047] mmc0: error -88 whilst initialising SD card
[ 50.142414] mmc0: error -88 whilst initialising SD card
[ 50.419218] mmc0: error -88 whilst initialising SD card
...
Fix this by reducing the clock speed to 48 MHz instead of 50 MHz, which
is also the value used in upstream Linux mt7621.dtsi.
With that change applied SD cards work as expected on MT7621 devices
also with the new driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
1. Override max clock frequency to a stable value 24 MHz.
2. Use voltage regulator to control the power supply.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Add all essential MTK SDHC properties to support the new mmc-mtk
driver. Since this driver relies on power regulators, we also
need to enable this feature for MT7620, just like MT762{1,8}.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Co-authored-by: John Thomson <git@johnthomson.fastmail.com.au>
"cd-inverted" is an upstream documented property used to indicate
the CD line is actived high. We will introduce a new upstream SDHC
driver, and this change will make them compatible with each other.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
In the past few years, we have received several reports about SPI
Flash not working properly. This is caused by excessively fast
clock frequency. It's really annoying to fix them one by one. Let's
reduce these aggressive frequencies to 50 MHz. This is a safe and
suggested value in the vendor SDK.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The new numberspace base starts from 512 instead of 0. The number
base seems come from the kernel symbol CONFIG_GPIOLIB_FASTPATH_LIMIT.
Suppress warning:
gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
These removed compatible strings do not exist in the source code
nor the dt-binding documents. They are useless.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Turns out the device got two buttons, while the currently listed on is
actually WPS, and the other (will hidden) button is intended as RESET.
Update DT accordingly.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Convert line endings from DOS to Unix using dos2unix.
Fixes: 2da2705a44 ("ramips: add support for WINSTARS WS-WN536P3")
Fixes: 5560791bbd ("ramips: add support for OpenFi 5Pro Travel Router")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Move nvmem-cells definitions to dts files for compatibility with other files
in which mt7628an_tplink_8m.dtsi is loaded, to prevent overwriting
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Comment:
No need to change the bootloader using breedweb anymore.
But breedweb can still be used.
Changes:
1. Update device baudrate
2. Update some of leds and button gpios values and names
3. Update partition layout to match the stock layout
4. Update missing package depends for usb
5. Add device UIMAGE Magic value
Signed-off-by: Yogi Hermawan <yogist.xda@gmail.com>
This file is executable:
target/linux/ramips/dts/mt7621_dlink_dir-2150-a1.dts
Has to be fixed.
Fixes: 30e8fd73ec ("ramips: Add support for D-Link DIR-2150-A1")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
This commit fixes random lan mac for sercomm dxx devices.
Fixes: 3395184825 ("ramips: mt7621: nix mac-address-increment")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
The WLR-1240 (ZX-5434) is an AC1200 Wave 2 outdoor repeater
with omnidirectional antennas for wall or pole mounting.
The device is manufactured by Todaair and meant to be used with
a tuya-based app, there is no webinterface for configuration.
Specifications:
- MT7628AN, 8 MiB SPI NOR flash, 64 MiB RAM, 2x2 802.11n
- MT7613 2x2 802.11ac Wave 2
- 802.3af PoE or 12V 1A 5.5x2.1 power supply (included)
- top RGB LED ring
TFTP installation:
- rename sysupgrade to `firmware_auto.bin`
- provide at 192.168.1.10 during boot
HTTP installation:
- keep reset button pressed for 5 seconds during power on (light blue
LED flashes slowly, then quickly to confirm, then remains steady on)
- recovery web interface is at 192.168.1.1, upload sysupgrade
Opening the device
- use suction cup to remove top cap within LED ring
- two screws are located in holes underneath silicone sealant
- two further screws are located at the bottom
initramfs boot
- open device, connect serial console (pins are labelled)
- keep pressing `4` during second tftp attempt to enter uboot shell
- run `tftpboot 82000000` to avoid memory overlap, then `bootm`
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
The WLR-1230 (ZX-5207) is an AC1200 Wave 2 outdoor repeater
with sector antennas for wall or pole mounting.
The device is manufactured by Todaair and meant to be used with
a tuya-based app, there is no webinterface for configuration.
Specifications:
- MT7628AN, 8 MiB SPI NOR flash, 64 MiB RAM, 2x2 802.11n
- MT7613 2x2 802.11ac Wave 2
- 802.3af PoE or 12V 1A 5.5x2.1 power supply (included)
- 3 LEDs WLAN, LAN, RES; PWR LED is not software-controllable
TFTP installation:
- rename sysupgrade to `firmware_auto.bin`
- provide at 192.168.1.10 during boot
HTTP installation:
- keep reset button pressed for 5 seconds during power on (LEDs
flash slowly, then quickly to confirm, then remain steady on)
- recovery web interface is at 192.168.1.1, upload sysupgrade
Opening the device
- two screws are located in the bottom left and right corners
underneath the label, inner tray slides out easily
initramfs boot
- open device, connect serial console (pins are labelled)
- keep pressing `4` during second tftp attempt to enter uboot shell
- run `tftpboot 82000000` to avoid memory overlap, then `bootm`
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Cudy assigns hardware versions to its devices on its website, and
the Cudy TR1200 router is now Cudy TR1200 v1.
OpenWrt currently uses both variants, and this commit removes
inconsistencies using only the new name.
Signed-off-by: Luis Mita <luis@luismita.com>
Buffalo WSR-2533DHPL2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based
on MediaTek MT7621A.
Specification:
- SoC : MediaTek MT7621AT
- RAM : DDR3 128 MiB (Winbond W631GG6MB12J)
- Flash : RAW-NAND 128 MiB (Winbond W29N01HVSINF)
- WLAN : 2.4/5 GHz (2x MediaTek MT7615N)
- Ethernet : 10/100/1000 Mbps x4
- Switch : MediaTek MT7530 (SoC)
- LED/keys : 8x/6x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB (J4)
- arrangement : 3.3V, GND, TX, RX from triangle-mark
- settings : 57600n8
- Power : 12VDC 1.5A
Flash instruction using factory.bin image:
1. boot WSR-2533DHPL2 normally with "Router" mode
2. access to the WebI ("http://192.168.11.1/") on the device and open
firmware update page
("管理" -> "ファームウェア更新")
3. select the OpenWrt factory.bin image and click update ("更新実行")
button
Attention: do not use "factory-uboot.bin" image
4. Wait ~120 seconds to complete flashing
Flash instruction using initramfs image:
1. prepare the TFTP server with the initramfs image renamed to
"linux.trx-recovery" and IP address "192.168.11.2"
2. press the "AOSS" button while powering on the WSR-2533DHPL2
3. after 10 seconds, release the "AOSS" button, WSR-2533DHPL2 downloads
the initramfs image and boot with it automatically
4. on the initramfs image, download the factory-uboot.bin image to the
device and perform sysupgrade with it and "-F" option
5. wait ~120 seconds to complete flashing
Notes:
- There are 2x factory*.bin images for different purposes.
- factory.bin : for flashing on OEM WebUI
- factory-uboot.bin: for flashing on OEM bootloader or initramfs image
factory-uboot.bin is useful for recoverying the device, or refreshing
when the kernel partition is expanded in the future. sysupgrade on
this device accepts factory-uboot.bin with option "-F", but on that
situation, user configurations won't be kept, so it's not for normal
use.
MAC addresses:
LAN : 18:EC:E7:xx:xx:E0 (board_data, "mac" (text))
WAN : 18:EC:E7:xx:xx:E0 (board_data, "mac" (text))
2.4 GHz: 18:EC:E7:xx:xx:E1 (Factory, 0x4 (hex))
5 GHz : 18:EC:E7:xx:xx:E4 (Factory, 0x8004 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Buffalo WSR-2533DHPLS is a 2.4/5 GHz band 11ac router, based on MediaTek
MT7621A.
Very similar to Buffalo WSR-2533DHPL, but with NAND, different GPIO
and TRX partitions.
Specification:
- SoC : MediaTek MT7621AT
- RAM : DDR3 256 MiB (Samsung K4B2G1646F-BYMA)
- Flash : RAW-NAND 128 MiB
(Winbond W29N01HV or KIOXIA TC58BVG0S3HTAI0)
- WLAN : 2.4/5 GHz (2x MediaTek MT7615N)
- Ethernet : 10/100/1000 Mbps
- Switch : MediaTek MT7530 (SoC) 4 ports
- LED/keys : 8x/6x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB (J4)
- arrangement : 3.3V, GND, TX, RX from triangle-mark
- settings : 115200n8
- Power : 12VDC 1.5A
Flash instruction using factory.bin image:
1. boot WSR-2533DHPLS normally with "Router" mode
2. access to the WebI ("http://192.168.11.1/") on the device and open
firmware update page
("管理" -> "ファームウェア更新")
3. select the OpenWrt factory.bin image and click update ("更新実行")
button
Attention: do not use "factory-uboot.bin" image
4. Wait ~120 seconds to complete flashing
Flash instruction using initramfs image:
1. prepare the TFTP server with the initramfs image renamed to
"linux.trx-recovery" and IP address "192.168.11.2"
2. press the "AOSS" button while powering on the WSR-2533DHPLS
3. after 10 seconds, release the "AOSS" button, WSR-2533DHPLS downloads
the initramfs image and boot with it automatically
4. on the initramfs image, download the factory-uboot.bin image to the
device and perform sysupgrade with it and "-F" option
5. wait ~120 seconds to complete flashing
Notes:
- The embedded addresses in eeprom data in Factory partition have
Buffalo's OUI, but they don't match with the actual addresses
assigned to wlan devices. So fixup addresses by the user-space
script.
root@localhost:/# hexdump -C /dev/mtdblock3 | grep "^0000[08]000\s"
00000000 15 76 a0 00 88 57 ee bc 01 a8 15 76 c3 14 00 80 |.v...W.....v....|
00008000 15 76 a0 00 88 57 ee bc 01 f8 15 76 c3 14 00 80 |.v...W.....v....|
See "MAC addresses" below for actual addresses.
- There are 2x factory*.bin images for different purposes.
- factory.bin : for flashing on OEM WebUI
- factory-uboot.bin: for flashing on OEM bootloader or initramfs image
factory-uboot.bin is useful for recoverying the device, or refreshing
when the kernel partition is expanded in the future. sysupgrade on
this device accepts factory-uboot.bin with option "-F", but on that
situation, user configurations won't be kept, so it's not for normal
use.
MAC addresses:
LAN : 90:96:F3:xx:xx:30 (board_data, "mac" (text))
WAN : 90:96:F3:xx:xx:30 (board_data, "mac" (text))
2.4 GHz: 90:96:F3:xx:xx:31
5 GHz : 90:96:F3:xx:xx:38
[original work]
Signed-off-by: Audun-Marius Gangstø <audun@gangsto.org>
[convert to ubi, fix/improve DT, add sysupgrade support]
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Switch trx parser to parser_trx of Linux Kernel from mtdsplit_trx to
split firmware partition using model-specific trx magic number on
some Buffalo devices.
This change is tested on Buffalo WSR-2533DHPL.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Hardware:
- SoC: MediaTek MT7628AN (MIPS 580MHz)
- Flash: 16 MiB XMC 25QH128CH10
- RAM: 128 MiB ESMT M14D1G1664A
- WLAN: 2.4 GHz (MT7628), 5 GHz (MT7613BEN 802.11ac)
- Ethernet: 1x 10/100 Mbps WAN, 1x 10/100 LAN (MT7628)
- USB 2.0 port
- Buttons: 1 Reset button, 1 slider button
- LEDs: 1x Red, 1x White
- Serial console: unpopulated header, 115200 8n1
- Power: 5 VDC, 2 A
MAC addresses:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 80:af:ca:xx:xx:x0 | label |
| LAN | 80:af:ca:xx:xx:x0 | label |
| WLAN 2g | 80:af:ca:xx:xx:x0 | label |
| WLAN 5g | 80:af:ca:xx:xx:x2 | label+2 |
+---------+-------------------+-----------+
Installation:
The installation must be done via TFTP by disassembling the router.
On other occasions Cudy has distributed intermediate firmware to make
installation easier, and so I recommend checking the Wiki for this
device if there is a more convenient solution than the one below.
To install using TFTP:
1. Upgrade to a beta firmware (signed by Cudy) that can be downloaded
from the wiki. This is required in order to use an unlocked u-boot.
2. Connect to UART.
3. While the router is turning on, press 1.
4. Connect to LAN and set your IP to 192.168.1.88/24. Configure a TFTP
server and an OpenWrt initramfs-kernel.bin firmware file as recovery.bin.
5. Press Enter three times. Verify the filename.
6. If you can reach LuCI or SSH now, just use the sysupgrade image with
the 'Keep settings' option turned off.
If you don't want to use the beta firmware nor the unlocked u-boot, you
can install the firmware writing the sysupgrade image on the firmware
partition of the SPI flash.
Signed-off-by: Luis Mita <luis@luismita.com>
Add support for D-Link DIR-2055 A1 based on similarities to DIR-1960 A1,
as well as various DIR-8xx A1 models. Existing DIR-1960 A1 openwrt
"factory" firmware installs without modifications via the D-Link Recovery
GUI and has no known incompatibilities with the DIR-2055 A1.
Changes to be committed:
new file: target/linux/ramips/dts/mt7621_dlink_dir-2055-a1.dts
modified: target/linux/ramips/image/mt7621.mk
modified: target/linux/ramips/mt7621/base-files/etc/board.d/01_leds
modified: target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh
Specifications:
Board: Not known
SoC: MediaTek MT7621 Family (MT7621AT)
RAM: 256 MB (Micron 9OK17 D9PTK, should be DDR3 MT41K128M16JT-125)
Flash: 128 MB (Winbond W29N01HVSINA)
WiFi: MediaTek MT7615 Family (MT7615N x2)
Switch: 1 WAN, 4 LAN (Gigabit)
Ports: 1 USB 3.0 (front)
Buttons: Reset, WiFi Toggle, WPS
LEDs: Power (white/orange), Internet (white/orange),
WiFi 2.4G (white), WiFi 5G (white)
Notes:
Only known difference vs. the DIR-1960 A1 is that the DIR-2055 A1
doesn't have a USB activity LED
Serial port:
Tested to be identical to various DIR-8xx A1 models with a similar
enclosure/pcb design:
Parameters: 57600, 8N1, 3.3V TTL no flow control
Location: J1 header (close to the Reset, WiFi and WPS buttons)
Pinout: 1 - VCC 2 - RXD 3 - TXD 4 - GND
Did not connect VCC when using
Installation:
D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to
http://192.168.0.1
Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
Signed-off-by: Keith Harrison <keithh@protonmail.com>
The gdma driver has been removed from the upstream. Let's move it
to the local files. This patch also removed unsupported compatible
string and sub-target.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
ELECOM WRC-X1800GS is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on
MT7621A.
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 256 MiB
- Flash : RAW-NAND 128 MiB (Macronix MX30LF1G28AD-TI)
- WLAN : 2.4/5 GHz 2T2R (MediaTek MT7915D)
- Ethernet : 5x 10/100/1000 Mbps
- switch : MediaTek MT7530 (SoC)
- LEDs/Keys (GPIO) : 7x/4x
- UART : pin-header on PCB ("J5")
- arrangement : 3.3V, TX, RX, NC, GND from tri-angle marking
- settings : 115200n8
- Power : 12 VDC, 1 A
Flash instruction using initramfs-factory image:
1. Boot WRC-X1800GS normally with "Router" mode
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt initramfs-factory image and click apply ("適用")
button
4. After flashing initramfs-factory image and reboot, upload the
sysupgrade image and perform sysupgrade with it
5. Wait ~120 seconds to complete flashing
Notes:
- WRC-X1800GS has 2x os images. Those are switched on every firmware
updating on stock firmware, but dual-boot feature on this device
cannot be handled on OpenWrt. So the 1st image is always used on
OpenWrt.
This is controlled by "bootnum" variable embedded in "persist"
partition (addr: 0x4).
- WRC-X1800GS has 2x HW revisions. There are some small changes, but the
same DeviceTree in stock firmware is used for both revisions.
On this support of WRC-X1800GS, 2x green:wlan-2g-N LEDs are defined
for each revision and the same default triggers are set.
MAC addresses:
LAN : 38:97:A4:xx:xx:38 (Factory, 0x1fdfa (hex) / Ubootenv, ethaddr (text))
WAN : 38:97:A4:xx:xx:3B (Factory, 0x1fdf4 (hex))
2.4 GHz: 38:97:A4:xx:xx:39
5 GHz : 38:97:A4:xx:xx:3A
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
