Ademar Arvati Filho
27b2f0fc0f
kirkwood: add support for Iomega Storcenter ix2-200
Iomega Storcenter ix2-200 is a dual SATA NAS powered by a Marvell
Kirkwood SoC clocked at 1GHz. It has 256MB of RAM and 32MB of
flash memory, 3x USB 2.0 and 1x 1Gbit/s NIC
Specification:
- SoC: Marvell Kirkwood 88F6281
- CPU/Speed: 1000Mhz
- Flash-Chip: Hynix NAND
- Flash size: 32 MiB,erase size:16 KiB,page size:512,OOB size:16
- RAM: 256MB
- LAN: 1x 1000 Mbps Ethernet
- WiFi: none
- 3x USB 2.0
- UART: for serial console
Installation instructions - easy steps:
1. download factory.bin and copy into tftp server
2. access uboot environment with serial cable and run
```
setenv mainlineLinux yes
setenv arcNumber 1682
setenv console 'console=ttyS0,115200n8'
setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)'
setenv bootargs_root 'root='
setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000'
saveenv
setenv serverip 192.168.1.1
setenv ipaddr 192.168.1.13
tftpboot 0x00800000 factory.bin
nand erase 0x100000 $(filesize)
nand write 0x00800000 0x100000 $(filesize)
run bootcmd
```
3. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13)
Installation steps nand bad blocks proof:
1. download initramfs-uImage and copy into usb ext2 partition
```
mkfs.ext2 -L ext2 /dev/sdh1
mount -t ext2 /dev/sdh1 /mnt
cp initramfs-uImage /mnt/initramfs.bin
umount /mnt
```
2. access uboot environment with serial cable and run
```
setenv mainlineLinux yes
setenv arcNumber 1682
setenv console 'console=ttyS0,115200n8'
setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)'
setenv bootargs_root 'root='
setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000'
saveenv
usb reset; ext2load usb 0:1 0x00800000 /initramfs.bin; bootm 0x00800000
```
3. log into openwrt and sysupgrade to install into flash
```
sysupgrade -n /tmp/sysupgrade.bin
```
4. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13)
Signed-off-by: Ademar Arvati Filho <arvati@hotmail.com>
2018-07-30 15:21:00 +02:00
..
2018-07-12 18:15:32 +02:00
2018-05-24 08:55:52 +02:00
2018-07-30 08:12:32 +02:00
2018-05-18 09:10:21 +02:00
2018-07-30 14:04:45 +02:00
2018-07-12 10:24:31 +02:00
2018-07-12 10:24:31 +02:00
2018-04-27 21:34:18 +02:00
2018-07-12 18:15:32 +02:00
2018-05-22 07:20:13 +02:00
2018-07-30 10:43:35 +02:00
2018-07-12 18:15:32 +02:00
2018-07-29 11:02:57 +02:00
2018-07-30 11:10:47 +02:00
2018-07-30 11:16:42 +02:00
2018-07-30 08:11:36 +02:00
2018-05-22 07:55:20 +02:00
2018-07-07 18:19:39 +02:00
2018-07-30 12:07:06 +02:00
2018-05-22 07:55:20 +02:00
2018-07-25 12:13:19 +02:00
2018-07-19 18:58:24 +02:00
2018-06-01 08:25:14 +02:00
2018-07-30 15:21:00 +02:00
2018-07-18 19:17:46 +02:00
2018-07-30 10:53:57 +02:00
2018-01-09 10:26:16 +01:00
2018-07-12 18:15:32 +02:00
2018-07-17 14:40:04 +02:00
2018-07-07 18:19:39 +02:00
2018-06-26 08:57:21 +02:00
2018-05-22 07:55:20 +02:00
2018-06-20 15:36:02 +02:00
2018-05-22 07:55:20 +02:00
2018-07-30 11:03:02 +02:00
2018-01-15 13:13:34 +01:00
2018-04-19 14:38:57 +02:00
2018-07-07 18:19:39 +02:00
2018-05-22 20:49:08 +02:00
2018-07-12 18:15:32 +02:00
2018-07-12 18:15:32 +02:00
2018-07-30 10:43:37 +02:00
2018-07-12 18:15:32 +02:00
2018-07-30 14:10:00 +02:00
2018-07-07 18:19:39 +02:00
2018-05-18 09:10:21 +02:00
2018-06-07 09:04:46 +02:00
2018-05-24 08:55:52 +02:00
2018-07-02 07:12:48 +02:00