fd0aaf93d1
This is an RTL8382-based switch with 24 copper ports + 4 SFP ports Specifications: --------------- * SoC: Realtek RTL8382M * Flash: 32 MiB SPI flash * RAM: 256 MiB * Ethernet: 24x 10/100/1000 Mbps * Buttons: 1x "Reset" button * UART: 1x serial header, unpopulated * SFP: 4 SFP ports Works: ------ - (24) RJ-45 ethernet ports - Switch functions - Buttons - Sys LED on front panel (no port LEDs) Not yet enabled: ---------------- - Port LEDs (no driver for RTL8231 in this mode) - SFP cages (no driver for PHY) Install via web interface: ------------------------- Not supported at this time. Install via serial console/tftp: -------------------------------- The U-Boot firmware drops to a TP-Link specific "BOOTUTIL" shell at 38400 baud. There is no known way to exit out of this shell, and no way to do anything useful. Ideally, one would trick the bootloader into flashing the sysupgrade image first. However, if the image exceeds 6MiB in size, it will not work. To install OpenWRT: Prepare a tftp server with: 1. server address: 192.168.0.146 2. the image as: "uImage.img" Power on device, and stop boot by pressing any key. Once the shell is active: 1. Ground out the CLK (pin 16) of the ROM (U6) 2. Select option "3. Start" 3. Bootloader notes that "The kernel has been damaged!" 4. Release CLK as soon as bootloader thinks image is corrupted. 5. Bootloader enters automatic recovery -- details printed on console 6. Watch as the bootloader flashes and boots OpenWRT. Blind install via tftp: ----------------------- This method works when it's not feasible to install a serial header. Prepare a tftp server with: 1. server address: 192.168.0.146 2. the image as: "uImage.img" 3. Watch network traffic (tcpdump or wireshark works) 4. Power on the device. 5. Wait 1-2 seconds then ground out the CLK (pin 16) of the ROM (U6) 6. When 192.168.0.30 makes tftp requests, release pin 16 7. Wait 2-3 minutes for device to auto-flash and boot OpenWRT Signed-off-by: Andreas Böhler <dev@aboehler.at>
100 lines
2.5 KiB
Plaintext
100 lines
2.5 KiB
Plaintext
|
|
. /lib/functions.sh
|
|
. /lib/functions/uci-defaults.sh
|
|
. /lib/functions/system.sh
|
|
|
|
ucidef_set_poe() {
|
|
json_select_object poe
|
|
json_add_string "budget" "$1"
|
|
json_select_array ports
|
|
for port in $2; do
|
|
if [ -n "$3" -a -n "$(expr "$3" : "\(.\+[[:space:]]\)\{0,1\}$port\([[:space:]].*\|\$\)")" ]; then
|
|
continue # skip ports passed via $3
|
|
fi
|
|
json_add_string "" "$port"
|
|
done
|
|
json_select ..
|
|
json_select ..
|
|
}
|
|
|
|
board=$(board_name)
|
|
board_config_update
|
|
|
|
lan_list=$(ls -1 -v -d /sys/class/net/lan* | xargs -n1 basename | xargs)
|
|
lan_list_rev=$(ls -1 -v -d -r /sys/class/net/lan* | xargs -n1 basename | xargs)
|
|
ucidef_set_bridge_device switch
|
|
ucidef_set_interface_lan "$lan_list"
|
|
|
|
lan_mac=""
|
|
lan_mac_start=""
|
|
lan_mac_end=""
|
|
label_mac=""
|
|
case $board in
|
|
hpe,1920-8g|\
|
|
hpe,1920-8g-poe-65w|\
|
|
hpe,1920-8g-poe-180w|\
|
|
hpe,1920-16g|\
|
|
hpe,1920-24g)
|
|
label_mac=$(mtd_get_mac_binary factory 0x68)
|
|
lan_mac=$label_mac
|
|
mac_count1=$(hexdump -v -n 4 -s 0x110 -e '4 "%d"' $(find_mtd_part factory) 2>/dev/null)
|
|
mac_count2=$(hexdump -v -n 4 -s 0x114 -e '4 "%d"' $(find_mtd_part factory) 2>/dev/null)
|
|
lan_mac_start=$(macaddr_add $lan_mac 2)
|
|
lan_mac_end=$(macaddr_add $lan_mac $((mac_count2-mac_count1)))
|
|
;;
|
|
tplink,sg2008p-v1|\
|
|
tplink,sg2210p-v3|\
|
|
tplink,sg2452p-v4|\
|
|
tplink,t1600g-28ts-v3)
|
|
label_mac=$(get_mac_label)
|
|
lan_mac="$label_mac"
|
|
;;
|
|
*)
|
|
lan_mac=$(mtd_get_mac_ascii u-boot-env2 mac_start)
|
|
lan_mac_end=$(mtd_get_mac_ascii u-boot-env2 mac_end)
|
|
label_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
|
|
[ -z "$lan_mac" ] && lan_mac=$label_mac
|
|
;;
|
|
esac
|
|
|
|
ucidef_set_interface_macaddr "lan" $lan_mac
|
|
ucidef_set_bridge_mac "$lan_mac"
|
|
ucidef_set_network_device_mac eth0 $lan_mac
|
|
[ -z "$lan_mac_start" ] && lan_mac_start=$lan_mac
|
|
for lan in $lan_list; do
|
|
ucidef_set_network_device_mac $lan $lan_mac_start
|
|
[ -z "$lan_mac_end" ] || [ "$lan_mac_start" == "$lan_mac_end" ] && lan_mac_start=$(macaddr_setbit_la $lan_mac_start)
|
|
lan_mac_start=$(macaddr_add $lan_mac_start 1)
|
|
done
|
|
[ -n "$label_mac" ] && ucidef_set_label_macaddr $label_mac
|
|
|
|
case $board in
|
|
hpe,1920-8g-poe-65w)
|
|
ucidef_set_poe 65 "$lan_list_rev" "lan9 lan10"
|
|
;;
|
|
hpe,1920-8g-poe-180w)
|
|
ucidef_set_poe 180 "$lan_list_rev" "lan9 lan10"
|
|
;;
|
|
netgear,gs110tpp-v1)
|
|
ucidef_set_poe 130 "$lan_list" "lan9 lan10"
|
|
;;
|
|
netgear,gs310tp-v1)
|
|
ucidef_set_poe 55 "$lan_list" "lan9 lan10"
|
|
;;
|
|
zyxel,gs1900-10hp)
|
|
ucidef_set_poe 77 "$lan_list" "lan9 lan10"
|
|
;;
|
|
zyxel,gs1900-8hp-v1|\
|
|
zyxel,gs1900-8hp-v2)
|
|
ucidef_set_poe 70 "$lan_list"
|
|
;;
|
|
zyxel,gs1900-24hp-v1|\
|
|
zyxel,gs1900-24hp-v2)
|
|
ucidef_set_poe 170 "$lan_list" "lan25 lan26"
|
|
;;
|
|
esac
|
|
|
|
board_config_flush
|
|
|
|
exit 0
|