mediatek: add CMCC RAX3000M NAND version support
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 5078ac8777)
This commit is contained in:
Tianling Shen
@@ -0,0 +1,246 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
/dts-v1/;
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
#include "mt7981.dtsi"
|
||||
|
||||
/ {
|
||||
model = "CMCC RAX3000M NAND version (custom U-Boot layout)";
|
||||
compatible = "cmcc,rax3000m-nand-ubootmod", "mediatek,mt7981";
|
||||
|
||||
aliases {
|
||||
led-boot = &red_led;
|
||||
led-failsafe = &red_led;
|
||||
led-running = &green_led;
|
||||
led-upgrade = &green_led;
|
||||
serial0 = &uart0;
|
||||
};
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
memory {
|
||||
reg = <0 0x40000000 0 0x10000000>;
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
button-reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&pio 1 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
button-mesh {
|
||||
label = "mesh";
|
||||
linux,code = <BTN_9>;
|
||||
linux,input-type = <EV_SW>;
|
||||
gpios = <&pio 0 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
green_led: led-0 {
|
||||
label = "green:status";
|
||||
gpios = <&pio 9 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led-1 {
|
||||
label = "blue:status";
|
||||
gpios = <&pio 12 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
red_led: led-2 {
|
||||
label = "red:status";
|
||||
gpios = <&pio 35 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ð {
|
||||
status = "okay";
|
||||
|
||||
gmac0: mac@0 {
|
||||
compatible = "mediatek,eth-mac";
|
||||
reg = <0>;
|
||||
phy-mode = "2500base-x";
|
||||
|
||||
nvmem-cells = <&macaddr_factory_2a>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
|
||||
fixed-link {
|
||||
speed = <2500>;
|
||||
full-duplex;
|
||||
pause;
|
||||
};
|
||||
};
|
||||
|
||||
gmac1: mac@1 {
|
||||
compatible = "mediatek,eth-mac";
|
||||
reg = <1>;
|
||||
phy-mode = "gmii";
|
||||
phy-handle = <&int_gbe_phy>;
|
||||
|
||||
nvmem-cells = <&macaddr_factory_24>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
};
|
||||
|
||||
&mdio_bus {
|
||||
switch: switch@0 {
|
||||
compatible = "mediatek,mt7531";
|
||||
reg = <31>;
|
||||
reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>;
|
||||
interrupt-controller;
|
||||
#interrupt-cells = <1>;
|
||||
interrupt-parent = <&pio>;
|
||||
interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
|
||||
};
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&spi0_flash_pins>;
|
||||
status = "okay";
|
||||
|
||||
spi_nand: flash@0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
compatible = "spi-nand";
|
||||
reg = <0>;
|
||||
|
||||
spi-max-frequency = <52000000>;
|
||||
spi-tx-buswidth = <4>;
|
||||
spi-rx-buswidth = <4>;
|
||||
mediatek,nmbm;
|
||||
mediatek,bmt-max-ratio = <1>;
|
||||
mediatek,bmt-max-reserved-blocks = <64>;
|
||||
|
||||
partitions: partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "BL2";
|
||||
reg = <0x00000 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x100000 0x80000>;
|
||||
};
|
||||
|
||||
factory: partition@180000 {
|
||||
label = "Factory";
|
||||
reg = <0x180000 0x200000>;
|
||||
|
||||
compatible = "nvmem-cells";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
macaddr_factory_24: macaddr@24 {
|
||||
reg = <0x24 0x6>;
|
||||
};
|
||||
|
||||
macaddr_factory_2a: macaddr@2a {
|
||||
reg = <0x2a 0x6>;
|
||||
};
|
||||
};
|
||||
|
||||
partition@380000 {
|
||||
label = "FIP";
|
||||
reg = <0x380000 0x200000>;
|
||||
};
|
||||
|
||||
partition@580000 {
|
||||
label = "ubi";
|
||||
reg = <0x580000 0x7200000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&switch {
|
||||
ports {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
port@0 {
|
||||
reg = <0>;
|
||||
label = "lan3";
|
||||
};
|
||||
|
||||
port@2 {
|
||||
reg = <2>;
|
||||
label = "lan2";
|
||||
};
|
||||
|
||||
port@3 {
|
||||
reg = <3>;
|
||||
label = "lan1";
|
||||
};
|
||||
|
||||
port@6 {
|
||||
reg = <6>;
|
||||
ethernet = <&gmac0>;
|
||||
phy-mode = "2500base-x";
|
||||
|
||||
fixed-link {
|
||||
speed = <2500>;
|
||||
full-duplex;
|
||||
pause;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pio {
|
||||
spi0_flash_pins: spi0-pins {
|
||||
mux {
|
||||
function = "spi";
|
||||
groups = "spi0", "spi0_wp_hold";
|
||||
};
|
||||
|
||||
conf-pu {
|
||||
pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
|
||||
drive-strength = <MTK_DRIVE_8mA>;
|
||||
bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
|
||||
};
|
||||
|
||||
conf-pd {
|
||||
pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
|
||||
drive-strength = <MTK_DRIVE_8mA>;
|
||||
bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usb_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&watchdog {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wifi {
|
||||
status = "okay";
|
||||
|
||||
mediatek,mtd-eeprom = <&factory 0x0>;
|
||||
};
|
||||
|
||||
&xhci {
|
||||
status = "okay";
|
||||
};
|
||||
@@ -33,6 +33,7 @@ mediatek_setup_interfaces()
|
||||
glinet,gl-mt3000)
|
||||
ucidef_set_interfaces_lan_wan eth1 eth0
|
||||
;;
|
||||
cmcc,rax3000m-nand-ubootmod|\
|
||||
h3c,magic-nx30-pro|\
|
||||
h3c,magic-nx30-pro-nmbm|\
|
||||
imou,lc-hx3001-ubootmod)
|
||||
|
||||
@@ -35,6 +35,9 @@ case "$board" in
|
||||
[ "$PHYNBR" = "0" ] && macaddr_add $addr 1 > /sys${DEVPATH}/macaddress
|
||||
[ "$PHYNBR" = "1" ] && macaddr_add $addr 2 > /sys${DEVPATH}/macaddress
|
||||
;;
|
||||
cmcc,rax3000m-nand-ubootmod)
|
||||
[ "$PHYNBR" = "1" ] && mtd_get_mac_binary Factory 0xa > /sys${DEVPATH}/macaddress
|
||||
;;
|
||||
cudy,wr3000-v1)
|
||||
addr=$(mtd_get_mac_binary bdinfo 0xde00)
|
||||
# Originally, phy0 is phy1 mac with LA bit set. However, this would conflict
|
||||
|
||||
@@ -185,6 +185,28 @@ define Device/cetron_ct3003-ubootmod
|
||||
endef
|
||||
TARGET_DEVICES += cetron_ct3003-ubootmod
|
||||
|
||||
define Device/cmcc_rax3000m-nand-ubootmod
|
||||
DEVICE_VENDOR := CMCC
|
||||
DEVICE_MODEL := RAX3000M NAND version (custom U-Boot layout)
|
||||
DEVICE_DTS := mt7981b-cmcc-rax3000m-nand-ubootmod
|
||||
DEVICE_DTS_DIR := ../dts
|
||||
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware \
|
||||
kmod-usb3 automount
|
||||
UBINIZE_OPTS := -E 5
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
IMAGE_SIZE := 116736k
|
||||
KERNEL_IN_UBI := 1
|
||||
IMAGES += factory.bin
|
||||
IMAGE/factory.bin := append-ubi | check-size $$$$(IMAGE_SIZE)
|
||||
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
||||
KERNEL = kernel-bin | lzma | \
|
||||
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
||||
KERNEL_INITRAMFS = kernel-bin | lzma | \
|
||||
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd
|
||||
endef
|
||||
TARGET_DEVICES += cmcc_rax3000m-nand-ubootmod
|
||||
|
||||
define Device/cudy_wr3000-v1
|
||||
DEVICE_VENDOR := Cudy
|
||||
DEVICE_MODEL := WR3000
|
||||
|
||||
Reference in New Issue
Block a user