The 00 address_mask needs to be inverted, otherwise the mac address
allocation will modify the last byte instead of the first one.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 1ee44825ad)
Some platforms a single ethernet device for all ports with multiple rx rings
and NAPI threading enabled. In this case, the steering script was limiting
performance by keeping all NAPI threads assigned to the same CPU.
Fix this by assigning each rx queue and the corresponding NAPI task separately.
Additionally, if the number of rx queues is at least as big as the number of
CPUs, skip weight based assignment and distribute the load across all CPUs
directly.
Fixes: https://github.com/openwrt/openwrt/issues/17611
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit acce25b789)
Bringing up a mesh interface using wpa_supplicant already supports a
per-VIF basic rate selection. Add the same ability when creating a mesh
VIF without wpa_supplicant.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 3deeb7805f)
This can be used to configure the base mac address from which all
interface mac addresses are derived
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 00860e485b)
Simplifies setting ifname to a different pattern for all affected
interfaces.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit a9ff3ba24b)
Basic rates were not set for mesh-interfaces, resulting in the undesired
behavior where 11s frames might be sent with a rate which was not
configured.
Depending on the driver, the basic rate might also be used to determine
the beacon rate configured to the chip. One such example are MediaTek
MT7915 platforms.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 3ec7f3a512)
On some drivers, setting the tx power on the interface is not enough.
Set it for the phy as well.
Fixes: 04fb05914e ("wifi-scripts: add multi-radio config support")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit b795e5cbcf)
Regarding SAE support in wifi-station:
Important Note: Unlike PSK wifi-stations, both `mac` and `key` options are required
to make it work. With PSK, hostapd used to perform a brute-force match to find which
PSK entry to use, but with SAE this is infeasible due to SAE's design.
When `mac` is omitted, it will allow any MAC address to use the SAE password if it
didn't have a MAC address assigned to it, but this could only be done once.
The last wildcard entry would be used.
Also, unlike "hostapd: add support for SAE in PPSK option" (commit 913368a),
it is not required to set `sae_pwe` to `0`. This gives it a slight advantage
over using PPSK that goes beyond not needing RADIUS.
Example Configuration:
```
config wifi-vlan
option iface default_radio0
option name 999
option vid 999
option network management
config wifi-station
# Allow user with MAC address 00:11:22:33:44:55 and matching
# key "secretadminpass" to access the management network.
option iface default_radio0
option vid 999
option mac '00:11:22:33:44:55'
option key secretadminpass
config wifi-vlan
option iface default_radio0
option name 100
option vid 100
option network guest
config wifi-station
# With SAE, when 'mac' is omitted it will be the fallback in case no
# other MAC address matches. It won't be possible for a user that
# has a matching MAC to use this network (i.e., 00:11:22:33:44:55
# in this example).
option iface default_radio0
option vid 100
option key guestpass
```
Regarding PSK file creation optimization:
This patch now conditionally runs `hostapd_set_psk_file` depending on `auth_type`.
Previously, `hostapd_set_psk` would always execute `hostapd_set_psk_file`, which
would create a new file if `wifi-station` was in use even if PSK was not enabled.
This change checks the `auth_type` to ensure that it is appropriate to parse the
`wifi-station` entries and create those files.
Furthermore, we now only configure `wpa_psk_file` when it is a supported option
(i.e., psk or psk-sae is used). Previously, we used to configure it when it was
not necessary. While it didn't cause any issues, it would litter `/var/run` with
unnecessary files. This patch fixes that case by configuring it depending on the
`auth_type`.
The new SAE support is aligned with these PSK file changes.
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/17145
Signed-off-by: John Crispin <john@phrozen.org>
(cherry picked from commit 65a1c666f2)
Link: https://github.com/openwrt/openwrt/pull/17248
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Don't fail wireless interface bringup on empty PSK set. This is a valid
configuration, resulting in a PSK network which can't be connected to.
It does not fail the bringup of the hostapd process.
Keep failing the interface setup in case a password with invalid length
is used.
This is also beneficial when intending to configure a PPSK network. It
allows to create a network where no PPSK is yet set.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 17a71f0c154cebd2e52cd8407531a9a88c931474)
Images for xrx200 8M flash are either not building due to image
size (TD-W8970, TD-W8980) or building such that the available
free space in the overlayfs is too little to be useful.
To keep images for these devices buildable, move them into a
small flash variant of the xrx200 subtarget. As these devices
are NOR flash only, remove NAND and UBI references from the
kernel config to gain some additional image size reduction.
The apparent 8M flash devices Arcadyan VGV7510KW22-brn,
Arcadyan VGV7519-brn and Lantiq Easy80920-nor seem to exist in
order to create special "factory" installation images for these
devices (which actually have larger flash: 16MB for the
Arcardyan devices; 64MB for the Lantiq device). As a
considerable amount of surgery would appear to be required to
the uboot-lantiq package structure to separate the "factory"
from the "sysupgrade" device recipes for these devices they
remain in the xrx200 target - if factory images aren't now
created, 23.05.x factory images should suffice for initial
installation.
Tested on: Netgear DM200, TP-Link TD-W8980,
AVM Fritz7490 (xrx200 subtarget: image build only)
Fixes: https://github.com/openwrt/openwrt/issues/16761
Signed-off-by: Andrew MacIntyre <andymac@pcug.org.au>
Link: https://github.com/openwrt/openwrt/pull/17113
(cherry picked from commit e63326e26a)
Link: https://github.com/openwrt/openwrt/pull/17303
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
e00958884416 fw4: do not add physical devices for soft offload
dfbcc1cd127c fw4: skip not existing netdev names in flowtable device list
18fc0ead19fa init: use the reload data trigger to reload firewall on procd data changes
Fixes: https://github.com/openwrt/openwrt/issues/13410
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 47c75a25cd)
058a099f5bc5 interface: fix memleak and reload issue for the zone attribute
ea01ed41f321 interface: remove unnecessary NULL checks before free()
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 53e312e193)
The initialization of mesh interfaces currently fail when wpa_supplicant
is not installed. This is due to the script calling the wpa_supplicant
feature indicator without verifying wpa_supplicant is installed at all.
To avoid failing, first check if wpa_supplicant is installed before
determining the available featureset.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 1be18c6daa)
86da5cbcdb9d system-linux: do not pull ifindex/flags from netlink messages on rtnl events
cd96f61ba63e proto-shell: fix spurious interface teardowns with host deps
a39fe3a8b150 wireless: add support for adding a list of devices for a wifi-iface
d29cf707478c iprule: add ipproto property
768027c5a764 system-linux: restore reading flags from netlink messages
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17074
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit f4492b6b1c)
Link: https://github.com/openwrt/openwrt/pull/17110
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fixup capabilities parsing in iw output.
In addition to the normal capabilities iw now also outputs HE MAC, HE
PHY and EHT MAC and EHT PHY capabilities. Exclude them in the parsing.
The grep returns this with mac80211-hwsim:
```
root@OpenWrt:~# iw phy phy0 info | grep 'Capabilities:'
Capabilities: 0x107e
HE PHY Capabilities: (0x02bfce0000000000000000):
EHT PHY Capabilities: (0x7c0000feffff7f01):
HE PHY Capabilities: (0x02bfce0000000000000000):
EHT PHY Capabilities: (0x7c0000feffff7f01):
HE PHY Capabilities: (0x02bf000000000000000000):
Capabilities: 0x107e
HE PHY Capabilities: (0x1cbfce0000000000000000):
EHT PHY Capabilities: (0xfc1f3ffeffff7f37):
HE PHY Capabilities: (0x1cbfce0000000000000000):
EHT PHY Capabilities: (0xfc1f3ffeffff7f37):
HE PHY Capabilities: (0x1cbf000000000000000000):
HE PHY Capabilities: (0x1cbfce0000000000000000):
EHT PHY Capabilities: (0xfefffffeffffff7f):
HE PHY Capabilities: (0x1cbfce0000000000000000):
EHT PHY Capabilities: (0xfefffffeffffff7f):
HE PHY Capabilities: (0x1cbf000000000000000000):
Capabilities: 0x107e
```
With busybox 1.36.1 the ht_cap_mask variable will be set to
-72057598332895361. With busybox 1.37.0 it will be set to -1.
Both values are wrong, after this change it will be set to 4222
(0x107E).
Link: https://github.com/openwrt/openwrt/pull/17043
(cherry picked from commit adf958c919)
Link: https://github.com/openwrt/openwrt/pull/17055
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
e93f6c3fc729 main: fix format string related warnings for log/debug printf functions
6ab44a2413f9 fix signed/unsigned comparison warnings
4fe997b61d7d system-dummy: add system_if_apply_settings_after_up
992d33cb42a6 ubus: add notifications on wireless device state changes
34eb11eb6f5c device/interface: add "tags" attribute from config to status dump
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 5f68e24333)
This allows annotating wifi interfaces in the config in a way that can be
queried through wifi status. One example use case is to mark wifi interfaces
for use with specific services without having to explicitly reference the
(often unnamed) sections from elsewhere.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit a3ec35cadb)
This is a preparation for adding support for dsl_cpe_pipe.sh with a
similar set of commands compared to the VDSL variant.
The configuration is simplified by using the "--enable-model" option.
Other options are chosen to match the VDSL variant, while also making
sure that previously enabled options stay like that. However, ReTx
options stay disabled, because of incompatibility with the ubus code.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20241019174041.1281093-3-jan@3e8.eu/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ffba75c9cd8f iptables: free xtables_match if found in need_protomatch
bf1d5fdf6234 iptables: fix regression with unintended free in need_protomatch
1aef9791a21e defaults.c: fix ipv6 flow offloading
Signed-off-by: Felix Fietkau <nbd@nbd.name>
