24bf4827cb
**SoC**: MediaTek MT7981B 2x A53
**Flash**: ESMT F50L1G41LB 128MB
**RAM**: NT52B128M16JR-FL 256MB
**Ethernet**: 4x 10/100/1000 Mbps
**Switch**: MediaTek MT7531AE
**WiFi**: MediaTek MT7976C
**Buttons**: Reset, Mesh
**Power**: DC 12V 1A
1. Get ssh access. Supported stock firmware **1.0.47**
```
curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0Anvram%20set%20ssh_en%3D1%0A"
curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0Anvram%20commit%0A"
curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0Ased%20-i%20's%2Fchannel%3D.*%2Fchannel%3D%22debug%22%2Fg'%20%2Fetc%2Finit.d%2Fdropbear%0A"
curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=*******/api/misystem/arn_switch" -d "open=1&model=1&level=%0A%2Fetc%2Finit.d%2Fdropbear%20start%0A"
curl -X POST "http://192.168.31.1/cgi-bin/luci/;stok=********/api/misystem/arn_switch" -d "open=1&model=1&level=%0Apasswd%20-d%20root%0A
```
2. Backup stock partitions
```
nanddump -f /tmp/BL2.bin /dev/mtd1
nanddump -f /tmp/Nvram.bin /dev/mtd2
nanddump -f /tmp/Bdata.bin /dev/mtd3
nanddump -f /tmp/Factory.bin /dev/mtd4
nanddump -f /tmp/FIP.bin /dev/mtd5
nanddump -f /tmp/ubi.bin /dev/mtd8
nanddump -f /tmp/KF.bin /dev/mtd12
```
Then transfer them to your computer in a safe place.
3. Get firmware information `cat /proc/cmdline`
4. Copy openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-initramfs-factory.ubi to **/tmp** and flash
If **firmware=0**
```
ubiformat /dev/mtd9 -y -f /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-initramfs-factory.ubi
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=1
nvram set flag_last_success=1
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
reboot
```
If **firmware=1**
```
ubiformat /dev/mtd8 -y -f /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-initramfs-factory.ubi
nvram set boot_wait=on
nvram set uart_en=1
nvram set flag_boot_rootfs=0
nvram set flag_last_success=0
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
reboot
```
Then reboot your router, it should boot to the OpenWrt initramfs system now.
5. Flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-squashfs-sysupgrade.bin
`sysupgrade -n /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-squashfs-sysupgrade.bin`
1. Flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb
`ubiformat /dev/mtd8 -y -f /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb`
`reboot`
2. Install kmod-mtd-rw
`opkg update && opkg install kmod-mtd-rw`
`insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1`
3. Format ubi and create new ubootenv volume
```
ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
```
4. *(Optional **-10Mb** free space) Add recovery boot feature.*
```
ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB
ubiupdatevol /dev/ubi0_2 /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb
```
5. Flash Openwrt U-Boot
```
mtd write /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-preloader.bin BL2
mtd write /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-bl31-uboot.fip FIP
```
6. Flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-squashfs-sysupgrade.itb
`sysupgrade -n /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-squashfs-sysupgrade.itb`
1. Force flash openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb
`sysupgrade -F -n /tmp/openwrt-mediatek-filogic-xiaomi_mi-router-ax3000t-ubootmod-initramfs-recovery.itb`
2. Format ubi and Nvram
```
ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8
mtd erase Nvram
```
3. Install kmod-mtd-rw
`opkg update && opkg install kmod-mtd-rw`
`insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1`
4. Flash stock images from backup
```
mtd write /tmp/BL2.bin BL2
mtd write /tmp/FIP.bin FIP
mtd write /tmp/ubi.bin ubi
```
Then reboot your router, waiting it finished rollback in minutes.
`ubiformat /dev/mtd7 -y -f /tmp/ubi.bin`
Then reboot your router, waiting it finished rollback in minutes.
Signed-off-by: Dim Fish <dimfish@gmail.com>
(cherry picked from commit 7dbcc1215a)
Project ImmortalWrt
ImmortalWrt is a fork of OpenWrt, with more packages ported, more devices supported, better performance, and special optimizations for mainland China users.
Compared the official one, we allow to use hacks or non-upstreamable patches / modifications to achieve our purpose. Source from anywhere.
Default login address: http://192.168.1.1 or http://immortalwrt.lan, username: root, password: none.
Download
Built firmware images are available for many architectures and come with a package selection to be used as WiFi home router. To quickly find a factory image usable to migrate from a vendor stock firmware to ImmortalWrt, try the Firmware Selector.
If your device is supported, please follow the Info link to see install instructions or consult the support resources listed below.
Development
To build your own firmware you need a GNU/Linux, BSD or MacOSX system (case sensitive filesystem required). Cygwin is unsupported because of the lack of a case sensitive file system.
Requirements
To build with this project, Ubuntu 20.04 LTS is preferred. And you need use the CPU based on AMD64 architecture, with at least 4GB RAM and 25 GB available disk space. Make sure the Internet is accessible.
The following tools are needed to compile ImmortalWrt, the package names vary between distributions.
- Here is an example for Ubuntu users:
-
Method 1:
Setup dependencies via APT
sudo apt update -y sudo apt full-upgrade -y sudo apt install -y ack antlr3 asciidoc autoconf automake autopoint binutils bison build-essential \ bzip2 ccache clang cmake cpio curl device-tree-compiler ecj fastjar flex gawk gettext gcc-multilib \ g++-multilib git gnutls-dev gperf haveged help2man intltool lib32gcc-s1 libc6-dev-i386 libelf-dev \ libglib2.0-dev libgmp3-dev libltdl-dev libmpc-dev libmpfr-dev libncurses5-dev libncursesw5 \ libncursesw5-dev libpython3-dev libreadline-dev libssl-dev libtool lld llvm lrzsz mkisofs msmtp \ nano ninja-build p7zip p7zip-full patch pkgconf python2.7 python3 python3-pip python3-ply \ python-docutils python3-pyelftools qemu-utils re2c rsync scons squashfs-tools subversion swig \ texinfo uglifyjs upx-ucl unzip vim wget xmlto xxd zlib1g-dev -
Method 2:
sudo bash -c 'bash <(curl -s https://build-scripts.immortalwrt.eu.org/init_build_environment.sh)'
-
Note:
- Do everything as an unprivileged user, not root, without sudo.
- Using CPUs based on other architectures should be fine to compile ImmortalWrt, but more hacks are needed - No warranty at all.
- You must not have spaces or non-ascii characters in PATH or in the work folders on the drive.
- If you're using Windows Subsystem for Linux (or WSL), removing Windows folders from PATH is required, please see Build system setup WSL documentation.
- Using macOS as the host build OS is not recommended. No warranty at all. You can get tips from Build system setup macOS documentation.
- For more details, please see Build system setup documentation.
Quickstart
- Run
git clone -b <branch> --single-branch --filter=blob:none https://github.com/immortalwrt/immortalwrtto clone the source code. - Run
cd immortalwrtto enter source directory. - Run
./scripts/feeds update -ato obtain all the latest package definitions defined in feeds.conf / feeds.conf.default - Run
./scripts/feeds install -ato install symlinks for all obtained packages into package/feeds/ - Run
make menuconfigto select your preferred configuration for the toolchain, target system & firmware packages. - Run
maketo build your firmware. This will download all sources, build the cross-compile toolchain and then cross-compile the GNU/Linux kernel & all chosen applications for your target system.
Related Repositories
The main repository uses multiple sub-repositories to manage packages of different categories. All packages are installed via the OpenWrt package manager called opkg. If you're looking to develop the web interface or port packages to ImmortalWrt, please find the fitting repository below.
- LuCI Web Interface: Modern and modular interface to control the device via a web browser.
- ImmortalWrt Packages: Community repository of ported packages.
- OpenWrt Routing: Packages specifically focused on (mesh) routing.
- OpenWrt Video: Packages specifically focused on display servers and clients (Xorg and Wayland).
Support Information
For a list of supported devices see the OpenWrt Hardware Database
Documentation
Support Community
- Support Chat: group @ctcgfw_openwrt_discuss on Telegram.
- Support Chat: group #immortalwrt on Matrix.
License
ImmortalWrt is licensed under GPL-2.0-only.
Acknowledgements
 |
 |