6fac6c29a7
Samsung WAM250 is a dual-band (selectable, not simultaneous) wireless
hub, dedicated for Samsung Shape Wireless Audio System. The device is
based on Atheros AR9344 (FCC ID: A3LWAM250). Support for this device
was first introduced in e58e49bdbe (ar71xx target).
Specifications:
- Atheros AR9344
- 560/450/225 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 2x 10/100 Mbps Ethernet
- 2T2R 2.4/5 GHz Wi-Fi, with ext. PA (SE2598L, SE5003L) and LNA
- 1x USB 2.0
- 4x LED (all are driven by GPIO)
- 2x button (reset, wps/speaker add)
- DC jack for main power input (14 V)
- UART header on PCB (J4, RX: 3, TX: 5)
Flash instruction:
This device uses dual-image (switched between upgrades) with a common
jffs2 config partition. Fortunately, there is a way to disable this mode
so that more flash space can be used by OpenWrt image.
You can easily access this device over telnet, using root/root
credentials (the same also work for serial console access).
1. Make sure that your device uses second (bootpart=2) image using
command: "fw_printenv bootpart".
2. If your device uses first image (bootpart=1), perform upgrade to the
latest vendor firmware (after the update, device should boot from
second partition) using web gui (default login: admin/1234567890).
3. Rename "sysupgrade" image to "firmware.bin", download it (you can use
wget, tftp or ftpget) to "/tmp" and issue below commands:
mtd_debug erase /dev/mtd3 0 $(wc -c /tmp/firmware.bin | awk -F' ' '{print $1}')
mtd_debug write /dev/mtd3 0 $(wc -c /tmp/firmware.bin)
fw_setenv bootpart
fw_setenv bootcmd "bootm 0x9f070000"
reboot
Revert to vendor firmware instruction:
1. Download vendor firmware to "/tmp" device and issue below commands:
fw_setenv bootpart 1
sysupgrade -n -F SS_BHUB_v2.2.05.bin
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
PROJECT OPENWRT
The Source Code of OpenWrt-Lean Modified by CTCGFW
Welcome to our Telegram Group: @ctcgfw_openwrt_discuss.
How to make it
Minimum requirements
Linux with case sensitive
2G DDR2 RAM
2 CPU Cores (AMD64, 1.4Ghz)
25G disk space left
Has access to both ChinaNet & Internet
Install the necessary packages (for Ubuntu user)
sudo apt-get update -y
sudo apt-get full-upgrade -y
sudo apt-get install -y build-essential asciidoc binutils bzip2 gawk gettext git libncurses5-dev libz-dev patch unzip zlib1g-dev lib32gcc1 libc6-dev-i386 subversion flex uglifyjs git-core gcc-multilib g++-multilib p7zip p7zip-full msmtp libssl-dev texinfo libreadline-dev libglib2.0-dev xmlto qemu-utils upx libelf-dev autoconf automake libtool autopoint ccache curl wget vim nano python python3 python-pip python3-pip python-ply python3-ply haveged lrzsz device-tree-compiler scons antlr3 gperf intltool rsync
For mainland China & Ubuntu(16.04+) user, you may run the following command to setup quickly:
sudo bash -c "bash <(curl -s https://build-scripts.project-openwrt.eu.org/init_build_environment.sh)"
Clone the source
git clone -b openwrt-18.06-k5.4 --single-branch https://github.com/project-openwrt/openwrt && cd openwrt
./scripts/feeds update -a && ./scripts/feeds install -a
Configure your firmware
make menuconfig
Make it
make -j1 V=s
Tips
You'd better not use root to make it, or you may be not able to use.
Default login address: 192.168.1.1, username is root and password is password.