ba288b2c83
Device specifications:
======================
* Qualcomm/Atheros AR9341 rev 1
* 535/400/200 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 2T2R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
- eth0
+ 802.3af POE
+ builtin switch port 1
+ used as LAN interface
- eth1
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to
the device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
PROJECT OPENWRT
The Source Code of OpenWrt-Lean Modified by CTCGFW
Welcome to our Telegram Group: @ctcgfw_openwrt_discuss.
How to make it
Minimum requirements
Linux with case sensitive
2G DDR2 RAM
2 CPU Cores (AMD64, 1.4Ghz)
25G disk space left
Has access to both ChinaNet & Internet
Install the necessary packages (for Ubuntu user)
sudo apt-get update -y
sudo apt-get full-upgrade -y
sudo apt-get install -y build-essential asciidoc binutils bzip2 gawk gettext git libncurses5-dev libz-dev patch unzip zlib1g-dev lib32gcc1 libc6-dev-i386 subversion flex uglifyjs git-core gcc-multilib g++-multilib p7zip p7zip-full msmtp libssl-dev texinfo libreadline-dev libglib2.0-dev xmlto qemu-utils upx libelf-dev autoconf automake libtool autopoint ccache curl wget vim nano python python3 python-pip python3-pip python-ply python3-ply haveged lrzsz device-tree-compiler scons antlr3 gperf intltool rsync
For mainland China & Ubuntu(16.04+) user, you may run the following command to setup quickly:
sudo bash -c "bash <(curl -s https://build-scripts.project-openwrt.eu.org/init_build_environment.sh)"
Clone the source
git clone -b openwrt-18.06-k5.4 --single-branch https://github.com/project-openwrt/openwrt && cd openwrt
./scripts/feeds update -a && ./scripts/feeds install -a
Configure your firmware
make menuconfig
Make it
make -j1 V=s
Tips
You'd better not use root to make it, or you may be not able to use.
Default login address: 192.168.1.1, username is root and password is password.