When building the mediatek/mt7629 target in OpenWrt 22.03 the kernel
does not have a configuration option for CONFIG_CRYPTO_DEV_MEDIATEK. Add
this option to the generic kernel configuration and also add two other
configuration options which are removed when we refresh the mt7629
kernel configuration.
Fixes: 2bea35cb55 ("mediatek: remove crypto-hw-mtk package")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit dcc0fe24ea)
Changes between 1.1.1o and 1.1.1p [21 Jun 2022]
*) In addition to the c_rehash shell command injection identified in
CVE-2022-1292, further bugs where the c_rehash script does not
properly sanitise shell metacharacters to prevent command injection have been
fixed.
When the CVE-2022-1292 was fixed it was not discovered that there
are other places in the script where the file names of certificates
being hashed were possibly passed to a command executed through the shell.
This script is distributed by some operating systems in a manner where
it is automatically executed. On such operating systems, an attacker
could execute arbitrary commands with the privileges of the script.
Use of the c_rehash script is considered obsolete and should be replaced
by the OpenSSL rehash command line tool.
(CVE-2022-2068)
[Daniel Fiala, Tomáš Mráz]
*) When OpenSSL TLS client is connecting without any supported elliptic
curves and TLS-1.3 protocol is disabled the connection will no longer fail
if a ciphersuite that does not use a key exchange based on elliptic
curves can be negotiated.
[Tomáš Mráz]
Signed-off-by: Andre Heider <a.heider@gmail.com>
(cherry picked from commit eb7d2abbf0)
The recent differentiation between v1 and v2 of the UniFi 6 LR added
support for the v2 version which has GPIO-controlled LEDs instead of
using an additional microcontroller to drive an RGB led.
The polarity of the white LED, however, was inverted and the default
states didn't make a lot of sense after all. Fix that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit f58e562b07)
The line trying to generate the standard sdcard.img.gz fails due to
boot.scr not being generated.
Remove the line in order to use the default sdcard.img.gz which is
exactly the same but includes generating the boot.scr file.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 1d3b57dbee)
Select matching U-Boot for both v1 and v2 variants.
Fixes: 15a02471bb ("mediatek: new target mt7622-ubnt-unifi-6-lr-v1")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 2caa03ec86)
Add targets:
* Ubiquiti UniFi 6 LR v2
* Ubiquiti UniFi 6 LR v2 (U-Boot mod)
This target does not have a RGB led bar like v1 did
Used target/linux/ramips/dts/mt7621_ubnt_unifi.dtsi as inspiration
The white dome LED is default-on, blue will turn on when the system is
in running state
Signed-off-by: Henrik Riomar <henrik.riomar@gmail.com>
(cherry picked from commit 31d86a1a11)
based on current ubnt_unifi-6-lr-ubootmod
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[added SUPPORTED_DEVICES for compatibility with existing setups]
Signed-off-by: Henrik Riomar <henrik.riomar@gmail.com>
(cherry picked from commit 5c8d3893a7)
Based on current mt7622-ubnt-unifi-6-lr, this is a preparation for
adding a v2 version of this target
* v1 - with led-bar
* v2 - two simple GPIO connected LEDs (in later commits)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[added SUPPORTED_DEVICES for compatibility with existing setups]
Signed-off-by: Henrik Riomar <henrik.riomar@gmail.com>
(cherry picked from commit 15a02471bb)
The config for LEDS_UBNT_LEDBAR doesn't stay in mt7629 kconfig because
of its I2C dependency. Build it as a module and let buildroot handle
this config option instead.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
(cherry picked from commit d9ea9c06e9)
The MediaTek's Crypto Engine module is only available for mt7623, in
which case it is built into the kernel.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit 3f2d0703b6)
Fix the wps button to prevent wrongly detected recovery procedures.
In the official banana pi r64 git the wps button is set to
GPIO_ACTIVE_LOW and not GPIO_ACTIVE_HIGH.
Import patch to fix on boot unwanted recovery entering:
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
- failsafe button wps was pressed -
- failsafe -
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry-picked from commit 6686194255)
The kernel configuration option CONFIG_MACH_MT7629 selects
CONFIG_HAVE_ARM_ARCH_TIMER now. Handle this change in the config-5.10.
This fixes some build problems.
Fixes: 81530d69ef ("kernel: bump 5.10 to 5.10.121")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
93e3fce916c6 mt76: pass original queue id from __mt76_tx_queue_skb to the driver
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 06d0cc2fb3)
c07f45927839 firmware: update mt7622 firmware to version 20220630
af406a2d1c36 mt76: do not use skb_set_queue_mapping for internal purposes
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 8e90abb396)
At least two AX820 hardware variants are known to exist, but they cannot
be distinguished (same hardware revision, no specific markings).
They appear to have the same LED hardware, but wired differently:
- One has a red system LED at GPIO 15, a green wlan2g LED at GPIO 14 and
a blue wlan5g LED at GPIO 16;
- The other only offers a green system LED at GPIO 15, with GPIO 14 and
16 being apparently not connected
Finally, a Yuncore datasheet says the canonical wiring should be:
- Blue wlan2g GPIO 14, green system GPIO 15, red wlan5g GPIO 16
All GPIOs are tied to a single RGB LED which is exposed via lightpipe on
the device front casing.
Considering the above, this patch exposes all three LEDs, preserves the
common system LED (GPIO 15) as the openwrt status LED, and removes the
color information from the LEDs names since it is not consistent across
hardware. The LED naming is made consistent with other YunCore devices.
A note is added in DTS to ensure this information is always available
and prevent unwanted changes in the future.
Fixes: #10131 "YunCore AX820: GPIO LED not correct"
Reviewed-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
No patches rebased, just checksum update for this refresh.
Build system: x86_64
Build-tested: ipq806x/R7800
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit c5882c33a7)
Enable PowerPC Book-E Watchdog Timer support. Having this enabled
in-kernel will result in procd starting it during boot.
This effectively solves the problem of the WDT in the Winbond W83793 chip
potentially resetting the system during sysupgrade, which could result
in an unbootable device. While the driver is modular, resulting in procd
not starting the WDT during boot (because that happens before kmod
load), the WDT handover during sysupgrade results in the WDT being
started. This normally shouldn't be a problem, but the W83793 WDT does
not like procd's defaults, nor the handover happening during sysupgrade.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit 04071cb111)
Avoid shipping ath10k board file in Mikrotik initram images
Most will only ever need to use these initram images once—to initially
load OpenWrt, but fix these images for more consistent Wi-Fi performance
between the initram and installed squashfs images.
OpenWrt BUILDBOT config ignores -cut packages in the initram images build.
This results in BUILDBOT initram images including the linux-firmware
qca4019 board-2.bin, and (initram image booted) Mikrotik devices loading
a generic BDF, rather than the intended BDF data loaded
from NOR as an api 1 board_file.
buildbot snapshot booted as initram image:
cat /etc/openwrt_version
r19679-810eac8c7f
dmesg | grep ath10k | grep -E board\|BDF
[ 9.794556] ath10k_ahb a000000.wifi: Loading BDF type 0
[ 9.807192] ath10k_ahb a000000.wifi: board_file api 2 bmi_id 0:16
crc32 11892f9b
[ 12.457105] ath10k_ahb a800000.wifi: Loading BDF type 0
[ 12.464945] ath10k_ahb a800000.wifi: board_file api 2 bmi_id 0:17
crc32 11892f9b
CC: Robert Marko <robimarko@gmail.com>
Fixes: 5eee67a72f ("ipq40xx: mikrotik: dont include ath10k-board-qca4019 by default")
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Reviewed-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 602b5f6c60)
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Since MikroTik subtarget now uses dynamic BDF loading its crucial that it
doesnt include the board-2.bin at all which is provided by the
ath10k-board-qca4019 package.
So to resolve this dont include the ath10k-board-qca4019 package on the
MikroTik subtarget.
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 5eee67a72f)
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Since we now provide the BDF-s for MikroTik IPQ40xx devices on the fly,
there is noneed to include package and ship them like we do now.
This also resolves the performance issues that happen as MikroTik
changes the boards and ships them under the same revision but they
actually ship with and require a different BDF.
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit ab141a6e2c)
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Since we now can pass the API 1 BDF-s aka board.bin to the ath10k
driver per radio lets use that to provide the BDF-s for MikroTik devices.
This also resolves the performance issues that happen as MikroTik changes
the boards and ships them under the same revision but they actually ship
with and require a different BDF.
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 4d4462cc2a)
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Some ath10k IPQ40xx devices like the MikroTik hAP ac2 and ac3 require the
BDF-s to be extracted from the device storage instead of shipping packaged
API 2 BDF-s.
This is required as MikroTik has started shipping boards that require BDF-s
to be updated, as otherwise their WLAN performance really suffers.
This is however impossible as the devices that require this are release under
the same revision and its not possible to differentiate them from devices
using the older BDF-s.
In OpenWrt we are extracting the calibration data during runtime and we are
able to extract the BDF-s in the same manner, however we cannot package the
BDF-s to API 2 format on the fly and can only use API 1 to provide BDF-s on
the fly.
This is an issue as the ath10k driver explicitly looks only for the board.bin
file and not for something like board-bus-device.bin like it does for pre-cal
data.
Due to this we have no way of providing correct BDF-s on the fly, so lets
extend the ath10k driver to first look for BDF-s in the board-bus-device.bin
format, for example: board-ahb-a800000.wifi.bin
If that fails, look for the default board file name as defined previously.
So, backport the upstream ath10k patch.
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 3daf2d477e)
[prune unrelated patch refreshes]
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Update ath10k-ct to the latest version which includes the backported
ath10k commit for requesting API 1 BDF-s with a unique name like caldata.
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit ab97b2a25d)
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
11f5c7b fw4.uc: fix zone helper assignment
b9d35ff fw4.uc: don't skip zone for unavailable helper
e35e26b tests: add test for zone helpers
a063317 ruleset: fix conntrack helpers
e1cb763 ruleset: reuse zone-jump.uc template for notrack and helper chain jumps
11410b8 ruleset: reorder declarations & output tweaks
880dd31 fw4: fix skipping invalid IPv6 ipset entries
5994466 fw4: simplify `is_loopback_dev()`
53886e5 fw4: fix crash in parse_cthelper() if no helpers are present
11256ff fw4: add support for configurable includes
3b5a033 tests: add test coverage for firewall includes
d79911c fw4: support sets with timeout capability but without default expiry
15c3831 fw4: add support for `option log` in rule and redirect sections
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit e8433fb433)
The random crashes observed with HARDENED_USERCOPY enabled no longer
seem to occur. Enable HARDENED_USERCOPY to improve security.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit 61587c9242)
We do not need support for 32 bit applications, as we're building
everything for 64 bit.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit 3e1848ee0f)
This patch provides support for the Firebox M300 reset button.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
(cherry picked from commit 19231cf838)
This patch provides support for the Firebox M300 only user-controllable
bi-color LED, and makes the green "shield" LED act as the typical
OpenWrt status led.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
(cherry picked from commit 4ab421b81d)
The MikroTik mAP-2nd (sold as mAP) is an indoor 2.4Ghz AP with
802.3af/at PoE input and passive PoE passthrough.
See https://mikrotik.com/product/RBmAP2nD for more details.
Specifications:
- SoC: QCA9533
- RAM: 64MB
- Storage: 16MB NOR
- Wireless: QCA9533 802.11b/g/n 2x2
- Ethernet: 2x 10/100 ports,
802.3af/at PoE in port 1, 500 mA passive PoE out on port 2
- 7 user-controllable LEDs
Note: the device is a tiny AP and does not distinguish between both
ethernet ports roles, so they are both assigned to lan.
With the current setup, ETH1 is connected to eth1 and ETH2 is connected
to eth0 via the embedded switch port 2.
Flashing:
TFTP boot initramfs image and then perform sysupgrade. The "ETH1" port
must be used to upload the TFTP image. Follow common MikroTik procedure
as in https://openwrt.org/toh/mikrotik/common.
Tested-By: Andrew Powers-Holmes <aholmes@omnom.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
(cherry picked from commit e1223dbee3)
Linux MTD requires the parent partition be writable for a child
partition to be allowed write permission.
In order for soft_config to be writeable (and modifiable via sysfs),
the parent RouterBoot partition must be writeable
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
(cherry picked from commit bb929a0f9c)
Linux MTD requires the parent partition be writable for a child
partition to be allowed write permission.
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
(cherry picked from commit 86fb287ad5)
Update this pending patch to remove the untested (variable eraseregions)
section, alongside simplifying the patch.
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
[refresh and split out unrelated refreshes]
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
(cherry picked from commit 4f7065ed25)
This adds the igc driver for the Intel 2.5GBit Ethernet chip to the
default packages.
Fixes: #10064
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit aae3a8a254)
OpenWrt now uses firewall4 (nft) by default,
so iptables should also default to nftables backend.
When multiple packages provide the same virtual package,
opkg pick the first one by alphabetical order,
so we rename iptables-legacy to iptables-zz-legacy and add
iptables-legacy in PROVIDES.
We also need to remove IPTABLES_NFTABLES config as
this cause recursive dependencies.
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
(cherry picked from commit 35fec487e3)
Kernel 5.10.124 introduced a new symbol 'LIB_MEMNEQ'. Add it to the
generic 5.10 config.
Fixes: 9e5d743422 ("kernel: bump 5.10 to 5.10.124")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit f3caba679b)
This requires U-Boot environment changes:
setenv OpenWrt_kernel watchguard_firebox-m300-fit-uImage.itb
setenv loadaddr 0x20000000
setenv wgBootSysA 'setenv bootargs root=/dev/mmcblk0p2 rw rootdelay=2 console=$consoledev,$baudrate fsl_dpaa_fman.fsl_fm_max_frm=1530; mmc dev 0; ext2load mmc 0:1 $loadaddr $OpenWrt_kernel; bootm $loadaddr'
Trying to sysupgrade an image containing this change on an M300 already
running OpenWrt will fail with the following error:
Tue Jun 14 12:06:21 EEST 2022 upgrade: The device is supported, but the config is incompatible to the new image (1.0->1.1). Please upgrade without keeping config (sysupgrade -n).
Tue Jun 14 12:06:21 EEST 2022 upgrade: Kernel switched to FIT uImage. Update U-Boot environment.
Tue Jun 14 12:06:21 EEST 2022 upgrade: Reading partition table from bootdisk...
Tue Jun 14 12:06:21 EEST 2022 upgrade: Extract boot sector from the image
Tue Jun 14 12:06:21 EEST 2022 upgrade: Reading partition table from image...
Image check failed.
This is to prevent rendering your device unbootable. Make the U-Boot
environment changes as instruced above, and then flash the image using
sysupgrade -F. The config can be kept, there is no need to use -n.
After the new image booted successfully, you can increase the compat_version:
uci set system.@system[0].compat_version='1.1'
uci commit
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit c4b499bc03)
Use the KERNEL_SUFFIX variable in Build/sdcard-img, rather than
using hardcoded "-kernel.bin", to allow overriding KERNEL_SUFFIX for a
device.
Fixes: 080a769b4d ("qoriq: new target")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit 86948716db)
No patches required a rebase, just updated checksum.
Build system: x86_64
Build-tested: ipq806x/R7800
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit 5202a511cc)
WolfSSL is crashing with an illegal opcode in some x86_64 CPUs that have
AES instructions but lack other extensions that are used by WolfSSL
when AES-NI is enabled.
Disable the option by default for now until the issue is properly fixed.
People can enable them in a custom build if they are sure it will work
for them.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit 0bd5367233)
Restore CONFIG_I8K + CONFIG_INTEL_INT0002_VGPIO that got
removed when I refreshed the config. Each x86 target gets
its own CONFIG_CRYPTO_BLAKE2S + LIB settings as only the
x86_64 can use the accelerated x86 version.
Also remove two extra spaces that sneaked into geode's config.
Fixes: 539e60539a ("generic: enable CRYPTO_LIB_BLAKE2S[_X86|_ARM]")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 9fc2d58bf8)
This is now built-in, enable so it won't propagate on target configs.
Link: https://lkml.org/lkml/2022/1/3/168
Fixes: 79e7a2552e ("kernel: bump 5.15 to 5.15.44")
Fixes: 0ca9367069 ("kernel: bump 5.10 to 5.10.119")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
(Link to Kernel's commit taht made it built-in,
CRYPTO_LIB_BLAKE2S[_ARM|_X86] as it's selectable, 5.10 backport)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 539e60539a)
This updates prereq-build.mk to find a suitable realpath utility, and
adds another place to look for a suitable getopt utility.
realpath has been used most notably by scripts/ipkg-build since
commit bb95be9265 ("scripts,ipkg-build: use realpath for pkg_dir")
and there are assorted other uses of it during a build.
It is ordinarily provided by GNU coreutils. This adds a SetupHostCommand
to locate it either under its own name or under grealpath, the name that
it will be available as under MacPorts or Homebrew, which use
--program-prefix=g.
Similarly, update the SetupHostCommand for getopt to be able to locate a
util-linux getopt at the default path used by MacPorts, in the same
fashion that
commit cc16f5d73e ("build: try to find getopt in macOS homebrew's standard location")'
did for Homebrew. As there is no standard alternative --program-prefix
for util-linux utilities in the way that GNU packages often use a "g"
prefix, this path-based approach is required in case a non-util-linux
getopt (such as one provided by an OS) shadows the util-linux getopt
in the PATH.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
(cherry picked from commit f614332197)
This adds a few fixes for compiling against Linux 5.10:
1. segment_eq() has been removed with upstream commit
428e2976a5bf7e7f5554286d7a5a33b8147b106a ("uaccess: remove
segment_eq") and can use uaccess_kernel() instead
2. ioremap_nocache() is removed and is now an alias for ioremap() with
upstream commit 4bdc0d676a643140bdf17dbf7eafedee3d496a3c ("remove
ioremap_nocache and devm_ioremap_nocache")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
(cherry picked from commit cd3de51bb4)
Existing conntracks will continue to be SNATed to 192.0.0.1 even after
464xlat interface gets teared down. To prevent this, matching
conntracks must be killed.
Signed-off-by: Alin Nastac <alin.nastac@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
(cherry picked from commit 289c46869b)
There is not RTC battery connected to the SoC of the UniFi 6 LR board.
Disable the RTC to prevent the system coming up with time set to
2000-01-01 00:00:00 after each reboot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 692d87a27b)
Some K2P comes with the worse boards with GD25Q128 (may be A2), which
only works with 50MHz frequency and less. Reduce spi frequency so that
these routers can boot.
remove m25p,fast-read because it isn't needed for 50MHz SPI.
Signed-off-by: Aviana Cruz <gwencroft@proton.me>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
(cherry picked from commit 857ea3f690)
902b321 wireless-regdb: Update regulatory rules for Israel (IL)
20f6f34 wireless-regdb: add missing spaces for US S1G rules
25652b6 wireless-regdb: Update regulatory rules for Australia (AU)
081873f wireless-regdb: update regulatory database based on preceding changes
166fbdd wireless-regdb: add db files missing from previous commit
e3f03f9 Regulatory update for 6 GHz operation in Canada (CA)
888da5f Regulatory update for 6 GHz operation in United States (US)
647bcaa Regulatory update for 6 GHz operation in FI
c6b079d wireless-regdb: update regulatory rules for Bulgaria (BG) on 6GHz
2ed39be wireless-regdb: Remove AUTO-BW from 6 GHz rules
7a6ad1a wireless-regdb: Unify 6 GHz rules for EU contries
68a8f2f wireless-regdb: update regulatory database based on preceding changes
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit e3e9eb31a2)
With some OS (Guix) the git submodule command is wrapped in
a script. Current logic parse the git submodule script directly.
If it's wrapped the prereq check wrongly fails while 'git submodule
--recursive' is actually available.
Add an additional check that try to directly use the 'git submodule'
command to check if the prereq is satisfied.
Fixes: #9986
Reported-by: Attila Lendvai <attila@lendvai.name>
Suggested-by: Attila Lendvai <attila@lendvai.name>
Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
(cherry picked from commit ab1f3a8706)
This reverts the airtime scheduler back from the virtual-time based scheduler
to the deficit round robin scheduler implementation.
This reduces burstiness and improves fairness by improving interaction with AQL.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 6d49a25804)
Tim Small reported:
| Viewing the 'Network' -> 'Switch' config page in LuCI:
|
| The LuCI LAN 1 port corresponds to the port physically
| labelled 2 at the rear of the device.
| [...]
|
| When a patch cord is attached to the port labelled 1 [...],
| the LED labelled °2 illuminates.
=> essentially, the Ports and LEDs are reversed.
Reported-by: Tim Small
Fixes: #10111
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 36483600d3)
For a TX->TX connected external phy to transmit/receive data, the rgmii2
pin group needs to be claimed with gpio function, at least for EdgeRouter X
SFP. We already claim the pin group under the pinctrl node with gpio
function on the gpio node on mt7621_ubnt_edgerouter-x.dtsi.
However, we should claim a pin group under its consumer node. It's the
ethernet node in this case, which we already claim the rgmii2 pin group
under it on mt7621.dtsi. Therefore, set the function as gpio on the rgmii2
node for EdgeRouter X SFP and get rid of claiming the rgmii2 pin group
under the pinctrl node. With this change, we also get to remove a
definition from mt7621_ubnt_edgerouter-x.dtsi which is specific to
EdgeRouter X SFP.
This change is tested on an EdgeRouter X SFP.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
(cherry picked from commit a1ad837735)
Make sure BootingFlag points to the system partition we install to.
The BootingFlag variable selects which system partition the system
boots from (0 => "Kernel", 1 => "Kernel2"). OpenWrt does not yet have
device specific support for this dual image scheme, and can therefore
only boot from "Kernel".
This has not been an issue until now, since all known OEM firmware
versions have ignored "Kernel2" - leaving the BootingFlag fixed at 0.
But the newest OEM firmware has a new upgrade procedure, installing
to the "inactive" system partition and setting BootingFlag accordingly.
This workaround is needed until the dual image scheme is fully
supported.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
(cherry picked from commit 79112e7d47)
It was observed that `rootfs_data` was sometimes not correctly erased
after performing sysupgrade, resulting in previous settings to prevail.
Add call to `wrgg-pad-rootfs` in sysupgrade image recipe to ensure any
previous jffs2 will be wiped, consistent with DAP-2610 from the ipq40xx
target, which introduced the double-flashing procedure for these devices.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
(cherry picked from commit f770c33d7b)
If the RTC module is compiled as a module, the hctosys fails to
initialize because ds1307 is loaded later.
Fixes:
[ 2.004145] hctosys: unable to open rtc device (rtc0)
[ 11.957997] rtc-ds1307 0-006f: registered as rtc0
This is similar to commit 5481ce9a11,
which was done for imx6 target.
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
(cherry picked from commit dc7f78da97)
with the switch to DSA setup, the switch gets correctly
programmed via the device-tree now. This hack is no
longer necessary.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 554ca44730)
adds `libusb-1.0.so` link on the target root again.
Fixes: 43539a6aab ("libusb: make InstallDev explicit")
Signed-off-by: Leo Soares <leo@hyper.ag>
(added fixed tag, reworded commit)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit dc59a22f1d)
65042bfd759c mt76: mt7915: introduce 802.11ax multi-bss support
e756ea3bd069 mt76: fix wrong HE data rate in sniffer tool
47b64131e820 mt76: mt7921: don't enable beacon filter when IEEE80211_CONF_CHANGE_MONITOR is set
7a05f4628e76 mt76: fix monitor rx FCS error in DFS channel
104dd5cb0a40 mt76: mt7915: fix DBDC default band selection on MT7915D
a7805e4e1d58 mt76: reduce tx queue lock hold time
0b1deb9292cd mt76: dma: use kzalloc instead of devm_kzalloc for txwi
2e51013b38c9 mt76: dma: reduce lock contention in mt76_dma_tx_cleanup
c96fbb86f7e5 mt76: mt7915: rework hardware/phy initialization
c2bb44cab51e mt76: mt7915: accept rx frames with non-standard VHT MCS10-11
36c23a4a8422 mt76: mt7921: accept rx frames with non-standard VHT MCS10-11
5b7dd093c8f0 mt76: fix use-after-free by removing a non-RCU wcid pointer
c692aacb9bde mt76: fix MBSS index condition in DBDC mode
fd6541905aa4 mt76: mt7921u: add suspend/resume support
201b33cf42c2 mt76: mt7921: rely on mt76_dev rxfilter in mt7921_configure_filter
9666c08228e7 mt76: mt7921: honor pm user configuration in mt7921_sniffer_interface_iter
1442710d7936 mt76: mt7915: always call mt7915_wfsys_reset() during init
ec4d9b9e8b70 mt76: mt7915: fix unbounded shift in mt7915_mcu_beacon_mbss
6b1efcd72946 mt76: mt7915: fix wfsys reset regression
376ea8152b2b mt76: mt7915: add missing chunk from wfsys reset fix
eed44048ca57 Revert "mt76: dma: reduce lock contention in mt76_dma_tx_cleanup"
5beb87716e70 mt76: dma: add wrapper macro for accessing queue registers
e0bc736d5617 mt76: add support for overriding the device used for DMA mapping
b8c842daa081 mt76: make number of tokens configurable dynamically
87a962e0608f mt76: mt7915: add Wireless Ethernet Dispatch support
2accb74e6be3 mt76: mt7915: fix using null pointer when wfsys on
e5227f2f3120 mt76: mt7921: Fix the error handling path of mt7921_pci_probe()
ec0e9f4da32f mt76: mt7915: fix possible uninitialized pointer dereference in mt7986_wmac_gpio_setup
5a87be892ba7 mt76: mt7915: fix possible NULL pointer dereference in mt7915_mac_fill_rx_vector
fe441e5d3dcf mt76: mt7915: do not pass data pointer to mt7915_mcu_muru_debug_set
f3ddfe886283 mt76: mt7915: report rx mode value in mt7915_mac_fill_rx_rate
2a0d370cb5fe mt76: mt7915: use 0xff to initialize bitrate_mask in mt7915_init_bitrate_mask
506bb0605e3e mt76: mt7921: Add AP mode support
d4937118ec4f mt76: fix rx reordering with non explicit / psmp ack policy
f50672518bcc mt76: do not attempt to reorder received 802.3 packets without agg session
75e046e3c9ae mt76: fix antenna config missing in 6G cap
64ede85f14b5 mt76: mt7915: remove SCS feature
db0a67582028 mt76: mt7915: make read-only array ppet16_ppet8_ru3_ru0 static const
68a2f68d5c01 mt76: mt7921: make read-only array ppet16_ppet8_ru3_ru0 static const
1e7b77294e97 mt76: mt7921: fix kernel crash at mt7921_pci_remove
795830a99a6c mt76: mt7915: add debugfs knob for RF registers read/write
60a8ec12a8eb mt76: mt7603: move spin_lock_bh() to spin_lock()
5ec7a2eac867 mt76: mt7915: disable RX_HDR_TRANS_SHORT
eecbb4992073 mt76: fix encap offload ethernet type check
a666d5637bc3 mt76: fix tx status related use-after-free race on station removal
6da21a0b7280 linux-firmware: update firmware for MT7921 WiFi device
4876688c41dc linux-firmware: update firmware for MT7915
79b1b86040de linux-firmware: add firmware for MT7986
784c27b159b9 linux-firmware: add firmware for MT7922
079e41dc71a1 mt76: mt7915: configure soc clocks in mt7986_wmac_init
747c70fc6c89 mt76: connac: use skb_put_data instead of open coding
e98f58815018 mt76: mt7915: update mt7986 patch in mt7986_wmac_adie_patch_7976()
b7104b4b2f2d mt76: mt7915: fix twt table_mask to u16 in mt7915_dev
d39368f336ee mt76: mt7915: reject duplicated twt flows
4718ed04a655 mt76: mt7915: limit minimum twt duration
84319691b742 mt76: mt7915: reowrk SER debugfs knob
bac5f22365a2 mt76: mt7915: introduce mt7915_mac_severe_check()
81524067686c mt76: mt7915: move MT_INT_MASK_CSR to init.c
2b7f5e85290e mt76: mt7915: add support for 6G in-band discovery
31273183ea0a mt76: mt7615/mt7915: do reset_work with mt76's work queue
bb54f5e1c115 mt76: mt7915: improve error handling for fw_debug knobs
838529da6470 mt76: mt7915: add more statistics from fw_util debugfs knobs
3a65deb93737 mt76: add gfp to mt76_mcu_msg_alloc signature
8e87669eefcf mt76: mt7921: add ipv6 NS offload support
e1b2c18eee29 mt76: mt7915: fix endianness in mt7915_rf_regval_get
0742eaeafee2 mt76: mt76x02u: fix possible memory leak in __mt76x02u_mcu_send_msg
d299ad96d867 mt76: mt7915: fix endian bug in mt7915_rf_regval_set()
380eac6f31ec mt76: add 6 GHz band support in mt76_sar_freq_ranges
268ce38e9e36 mt76: mt7921: introduce ACPI SAR support
8c27300b4271 mt76: mt7921: introduce ACPI SAR config in tx power
54b6504a3ef8 mt76: mt7915: add more ethtool stats
cdd66d642977 mt76: add DBDC rxq handlings into mac_reset_work
b284684f5cba mt76: mt7921: add PATCH_FINISH_REQ cmd response handling
f8b9be4287cc mt76: mt7921s: fix firmware download random fail
28b19d2cc53f mt76: mt7915: add missing bh-disable around tx napi enable/schedule
1d8af168e86f mt76: mt7615: add missing bh-disable around rx napi enable/schedule
4554ee652caf mt76: mt7921: fix warning Using plain integer as NULL pointer
a3f1d6ccf3ca mt76: mt7921: add missing bh-disable around rx napi schedule
9aeca2a5ce47 mt76: mt7921: get rid of mt7921_mcu_exit
fee8a5911c76 mt76: connac: move shared fw structures in connac module
db4d784ae7ba mt76: mt7921: move fw toggle in mt7921_load_firmware
16ab6bf49556 mt76: connac: move mt76_connac2_load_ram in connac module
29fd748801c6 mt76: connac: move mt76_connac2_load_patch in connac module
051c68d18214 mt76: mt7663: rely on mt76_connac2_fw_trailer
d6ae3505ac6c mt76: enable the VHT extended NSS BW feature
488a5ccc9762 mt76: mt7921: rely on mt76_dev in mt7921_mac_write_txwi signature
934029bb93e2 mt76: mt7915: rely on mt76_dev in mt7915_mac_write_txwi signature
ecefae4c7d72 mt76: connac: move mac connac2 defs in mt76_connac2_mac.h
b5eecc841df8 mt76: connac: move connac2_mac_write_txwi in mt76_connac module
012e619a07b9 mt76: connac: move mt76_connac2_mac_add_txs_skb in connac module
1b492be795ea mt76: mt7921: not support beacon offload disable command
f1f46d3b4b19 mt76: mt7921: fix command timeout in AP stop period
cae61112ef1d mt76: connac: move HE radiotap parsing in connac module
487674062643 mt76: connac: move mt76_connac2_reverse_frag0_hdr_trans in mt76-connac module
649bdc4983c4 mt76: connac: move mt76_connac2_mac_fill_rx_rate in connac module
cb75aaa39252 mt76: mt7921s: remove unnecessary goto in mt7921s_mcu_drv_pmctrl
e0eaf66eaebb mt76: mt7615: do not update pm stats in case of error
f8d125b4ea30 mt76: mt7921: do not update pm states in case of error
6329a834907e mt76: mt7921s: fix possible sdio deadlock in command fail
8a04f1b04662 mt76: mt7921: fix aggregation subframes setting to HE max
e52283439094 mt76: mt7915: disable UL MU-MIMO for mt7915
fd3958970e3d mt76: mt7921: enlarge maximum VHT MPDU length to 11454
18df38fe77f7 mt76: mt7915: get rid of unnecessary new line in mt7915_mac_write_txwi
149e95f5d7a6 mt76: connac: move mt76_connac_fw_txp in common module
899d192e8a79 mt76: move mt7615_txp_ptr in mt76_connac module
7184f0a6f6a5 mt76: connac: move mt76_connac_tx_free in shared code
c42d45278fa5 mt76: connac: move mt76_connac_tx_complete_skb in shared code
0993f4ef96f8 mt76: connac: move mt76_connac_write_hw_txp in shared code
467960fab791 mt76: connac: move mt7615_txp_skb_unmap in common code
2e758064b085 mt76: mt7915: rely on mt76_connac_tx_free
2065a7901671 mt76: move mcu_txd/mcu_rxd structures in shared code
576c1b7c472b mt76: move mt76_connac2_mcu_fill_message in mt76_connac module
7275f7758090 mt76: mt7915: fix incorrect testmode ipg on band 1 caused by wmm_idx
1696f9eb8b40 mt76: mt7915: do not copy ieee80211_ops pointer in mt7915_mmio_probe
a4db5869d660 mt76: mt7915: update mpdu density in 6g capability
500c18014d95 mt76: mt7915: add sta_rec with EXTRA_INFO_NEW for the first time only
3ef66fc7c714 mt76: do not check the ccmp pn for ONLY_MONITOR frame
dd682eead016 mt76: mt7915: update the maximum size of beacon offload
4fb991f2c997 mt76: mt7615: add sta_rec with EXTRA_INFO_NEW for the first time only
ba39ed3b44f1 mt76: mt76x02: improve reliability of the beacon hang check
fd8211cf7c59 mt76: mt7921: sync with updated patch
f2edd340ddb4 mt76: allow receiving frames with invalid CCMP PN via monitor interfaces
b6e865e2cc70 mt76: mt7615: fix throughput regression on DFS channels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 29ed58c8be)
The Netgear GS3xx devices do not properly initialise the port LEDs during
startup unless the boot command in U-Boot is changed. Making the U-Boot
env partition writable allows this modification to be done from within
OpenWrt by calling "fw_setenv bootcmd rtk network on\; boota".
Signed-off-by: Andreas Böhler <dev@aboehler.at>
(cherry picked from commit d9e12c21fa)
Make the u-boot environment partition for the NETGEAR
GS108T v3 and GS110TPP writable (they share a DTS), so
the values can be manipulated from userspace.
See https://forum.openwrt.org/t/57875/1567 for a real
world example.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
(cherry picked from commit 9c381d3386)
Downstream projects might re-generate device-specific configuration
based on OpenWrt's defaults on each upgrade, thus being unaffected by
forward- as well as backwards-breaking configuration.
Add a new sysupgrade parameter, which allows sysupgrades between minor
compat-versions. Upgrades will still fail upon mismatching major compat
versions.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 34437af888)
The Netgear GS108Tv3 is already supported by OpenWrt, but is missing LED
support. After OpenWrt installation, all LEDs are off which makes the
installation quite confusing.
This enables support for the green/amber power LED to give feedback
about the current status.
This is basically just a verbatim copy of commit c4927747d2 ("realtek:
add support for power LED on Netgear GS308Tv1").
Please note that both LEDs are wired up in an anti-parallel fashion,
which means that only one of both LEDs/colors can be switched on at the
same time. If both LEDs/colors are switched on simultanously, the LED
goes dark.
Tested-by: Pascal Ernster <git@hardfalcon.net>
Signed-off-by: Pascal Ernster <git@hardfalcon.net>
[add title to commit reference]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit adbdfc9366)
The Netgear GS308Tv1 is already supported by OpenWrt, but is missing LED
support. After OpenWrt installation, all LEDs are off which makes the
installation quite confusing.
This enables support for the green/amber power LED to give feedback
about the current status.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
(cherry picked from commit c4927747d2)
This reverts commit 33df033b73.
It was reported this commit breaks 802.11s mesh connections, failing
link establishment.
Reported-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
Both buttons on the RT-AC57U are active-low. Fix the GPIO flag for the
WPS cutton to fix button behavior.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 535b0c70b1)
All Freescale processors used in this target are capable to detect error
and correction. [1] It can not be used as kernel module. [2] This is
helpful to report hardware errors.
It enables three kernel options:
- EDAC, which is a subsystem
- EDAC_LEGACY_SYSFS, it enables sysfq nodes
- MP85XX, support for Freescale MPC8349, MPC8560, MPC8540, MPC8548, T4240
EDAC is already enabled for following targets:
qoriq, octeon, octeontx and zynq.
[1] https://cateee.net/lkddb/web-lkddb/EDAC.html
[2] https://patchwork.ozlabs.org/patch/554908/
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
(cherry picked from commit bfc73f42df)
We don't need to make sure that we want to have enabled
CONFIG_CMD_SETEXPR by default, since this is already done in U-boot [1].
This was actually needed only for clearfog board [2], which was added in
commit: da0005a6d08ae33d958a6d8a6c0c12dc07b5b2b8 ("uboot-mvebu: add
patch to enable setexpr for clearfog boards) and send to U-boot to fix
it properly. After a while, there was added support for Turris Omnia,
which uses setexpr as well [3], but for this board, there are no fixes
needed in U-boot and that's why we can remove this option here.
It is helpful with shell scripting. If some downstream distributions are
using it, they should correct it in defconfig for related boards.
[1] e95afa5675/cmd/Kconfig (L1504)
[2] 852126680e/target/linux/mvebu/image/clearfog.bootscript (L7)
[3] 852126680e/target/linux/mvebu/image/turris-omnia.bootscript (L2)
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
(cherry picked from commit 69cef74c67)
Needed by strongSwan IPsec VPN for strongswan-mod-chapoly. Not to be confused with
kmod-crypto-LIB-chacha20poly1305, which is an 8-byte nonce version used
by wireguard.
Signed-off-by: Xu Wang <xwang1498@gmx.com>
(cherry picked from commit 197b672c40)
This enables armv8 crypto extensions version of AES, GHASH, SHA1, and
CRC T10 algorithms in the kernel.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit 9be35180f4)
This enables armv8 crypto extensions version of AES, GHASH, and CRC T10
algorithms in the kernel.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit b1346d35e4)
Adds the crypto extensions version of the CRC T10 algorithm that is
already built into the kernel.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit 1b94e4aab8)
This enables armv8 crypto extensions version of AES, GHASH, SHA1,
SHA256, and SHA512 algorithms in the kernel.
The choice of algorithms match the 32-bit versions that are enabled in
the target config-5.10 file, but were only used by the cortexa9
subtarget.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit 06bb5ac1f2)
This is result of a plain make kernel_oldconfig CONFIG_TARGET=subtarget.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit 39b6af1147)
This enables armv8 crypto extensions version of AES, GHASH, SHA1,
SHA256, and SHA512 algorithms in the kernel.
The choice of algorithms match the 32-bit versions that are enabled in
the target config-5.10 file, but were only used by the cortexa9
subtarget.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit f5167e11bf)
This is result of a plain make kernel_oldconfig CONFIG_TARGET=subtarget.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit a4c6384d93)
This enables armv8 crypto extensions version of AES, GHASH, SHA256 and
CRC T10 algorithms in the kernel.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit eb33232420)
This enables armv8 crypto extensions version of AES and GHASH algorithms
in the kernel.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit b2cb87bc98)
This enables arm64/neon version of AES, SHA256 and SHA512 algorithms in
the kernel. bcm2711 does not support armv8 crypto extensions, so they
are not included.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit 7b6beb7489)
This enables arm64/neon version of AES, SHA256 and SHA512 algorithms in
the kernel. bcm2710 does not support armv8 crypto extensions, so they
are not included.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit 38ebb210a9)
The image builds and works fine on Asus RT-AC88U. Therefore, remove the
BROKEN flag from the makefile.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
(cherry picked from commit 5c1b1918ab)
Hannu Nyman wrote in openwrt's github issue #9962:
|Based on forum discussion, the commit 0bc794a
|"kernel: add support for Toshiba TC58NVG0S3HTA00 NAND flash"
|causes flash memory chip misdetection for some other
|Fritzbox devices, as the commit only defines a 4-byte flash
|memory chip ID that matches several chips used in the devices.
|
|See discussion from this onward
|<https://forum.openwrt.org/t/openwrt-22-03-0-rc1-first-release-candidate/126045/182>
|
|OpenWrt 22.03.0-rc2 and rc3 are causing on a Fritzbox 7412
|bootloops due to a misdetected flash chip.
|
|Yup, that patch is missing the 5th ID byte entirely - both chips
|share the same first 4;
|
| TC58NVG0S3HTA00 = 0x98 0xf1 0x80 0x15 0x72 (digikey datasheet, page 35)
| TC58BVG0S3HTA00 = 0x98 0xf1 0x80 0x15 0xf2 (digikey datasheet, page 28)
|
|The commit has also been backported to openwrt-22.03 after rc1,
|so both rc2 and rc3 suffer from this bug."
Andreas' TC58NVG0S3H seems not to follow Toshibas/Kioxa's own datasheet.
It only reports the first four bytes: "98 f1 80 15 00 00 00 00".
This patch changes the id_len in the entry to 8. This makes it so that
Andreas' NAND is still detected. At the same time, this prevents other
Toshiba NAND flash chips - that share the same four bytes - from being
misdetected.
Upstream (Miquel Raynal) decided to drop this patch for now. But he
advised to keep it in OpenWrt. As other devices could be affected.
<https://lore.kernel.org/linux-mtd/20220606155919.23001410@xps-13/>
Reported-by: Peter-vdL
Tested-by: Peter-vdL
Tested-by: Andreas B<C3><B6>hler <dev@aboehler.at>
Fixes: 0bc794a668 ("kernel: add support for Toshiba TC58NVG0S3HTA00 NAND flash")
Link: <https://github.com/openwrt/openwrt/issues/9962>
(actually move the patch, added comment about possible counterfeits)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Openvpn forces CONFIG_WOLFSSL_HAS_OPENVPN=y. When the phase1 bots build
the now non-shared package, openvpn will not be selected, and WolfSSL
will be built without it. Then phase2 bots have CONFIG_ALL=y, which
will select openvpn and force CONFIG_WOLFSSL_HAS_OPENVPN=y. This
changes the version hash, causing dependency failures, as shared
packages expect the phase2 hash.
Fixes: #9738
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This enables AES & SHA CPU instructions for compatible armv8, and x86_64
architectures. Add this to the hardware acceleration choice, since they
can't be enabled at the same time.
The package was marked non-shared, since the arm CPUs may or may not
have crypto extensions enabled based on licensing; bcm27xx does not
enable them. There is no run-time detection of this for arm.
NOTE:
Should this be backported to a release branch, it must be done shortly
before a new minor release, because the change to nonshared will remove
libwolfssl from the shared packages, but the nonshared are only built in
a subsequent release!
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit 0a2edc2714)
Enabling different hardware crypto acceleration should not change the
library ABI. Add them to PKG_CONFIG_DEPENDS after the ABI version hash
has been computed.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit 677774d445)
Delete the crypto-lib-blake2s kmod package, as BLAKE2s is now built-in.
Patches automatically rebased.
Build system: x86_64
Build-tested: ipq806x/R7800, x86/64
Signed-off-by: John Audia <therealgraysky@proton.me>
(cherry picked from commit cd634afe6c)
Major changes are:
Add support for smbd-direct multi-desctriptor.
Add support for dkms.
Add support for key exchange.
Fix seveal bugs.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(cherry picked from commit 95adbc24e7)
Small update to my previous path 'fix I2C on GL-AR300M devices'.
This update allow using GPIO17 as regular GPIO in case it not used
as I2C SDA line.
Signed-off-by: Ptilopsis Leucotis <PtilopsisLeucotis@yandex.com>
(cherry picked from commit 493080815d)
With the pinctrl configuration set properly by the previous commit, the
LED stays lit regardless of status of 2.4GHz radio, even if 5GHz radio
is disabled. Map GPIO19 as LED for ath9k, this way the LED will show
activity for both bands, as it is bound by logical AND with output of
ath10k-phy0 LED. This works well because during management traffic,
phy*tpt triggers typically cause LEDs to blink in unison.
Link: <https://github.com/openwrt/openwrt/pull/9941>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit 5ca45e0a21)
The default configuration of pinctrl for GPIO19 set by U-boot was not a
GPIO, but an alternate function, which prevented the GPIO hog from
working. Set GPIO19 into GPIO mode to allow the hog to work, then the
ath10k LED output can control the state of actual LED properly.
Link: <https://github.com/openwrt/openwrt/pull/9941>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit 82b5984636)
If you change SCAN_EXTRA variable with "-path target/linux/xxxx" in
include/toplevel.mk for speed up scan, find will warn with:
find: warning: you have specified the global option -maxdepth after
the argument -path, but global options are not positional, i.e.,
-maxdepth affects tests specified before it as well as those specified
after it. Please specify global options before other arguments.
The find option -mindepth -maxdepth are global options and must be
before any path option. Change order of $(SCAN_EXTRA) after -mindepth
and -maxdepth to fix this.
Signed-off-by: Leo Chung <gewalalb@gmail.com>
[capitalize Description, Author and Sob and minor description tweak]
Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
(cherry picked from commit eb787b5b9d)
- fix an issues when accessing the port pointer of an expired/invalid fdb entry
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 38a5b593ef)
Buidbots are currently choking on the following compile error:
In file included from tools/aisimage.c:9:
include/image.h:1133:12: fatal error: openssl/evp.h: No such file or directory
# include <openssl/evp.h>
^~~~~~~~~~~~~~~
compilation terminated.
This is caused by a complete overriding of make flags which are provided
correctly in `UBOOT_MAKE_FLAGS` variable, but currently overriden
instead of extended. This then leads to the usage of build host include
dirs, which are not available.
Fix it by extending `UBOOT_MAKE_FLAGS` variable in all device recipes.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 481339a042)
Some dst in IPv6 flow offload table become invalid after the table is created.
So check_dst is needed in packet path.
Signed-off-by: Ritaro Takenaka <ritarot634@gmail.com>
[Add patch for kernel 5.15 too and rename file]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit efff48529b)
ucidef_set_bridge_device is needed for DGND3700v2 network config since VLAN 1
must be used for the switch to be correctly configured.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 90e4c8c6e6)
f2d6752901f2 blob: clear buf->head when freeing a buffer
45210ce14136 list.h: add container_of_safe macro
cfa372ff8aed blobmsg: implicitly reserve space for 0-terminator in string buf alloc
d2223ef9da71 blobmsg: work around false positive gcc -Warray-bounds warnings
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 3e300e724b)
Stop the connection when the control daemon is terminated. The code is
a modified version of the termination routine in version 4.23.1 of the
daemon (which doesn't support VR9 modems anymore).
This could also be implemented by calling the acos and acs commands via
dsl_cpe_pipe.sh in the init script. However, doing it in the daemon
itself has the advantage of also working if it is terminated in another
way (for example during sysupgrade).
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
(cherry picked from commit 1daaef31b3)
The driver maintains elapsed times by repeatedly accumulating the time
since the previous update in a loop. For the elapsed showtime time, the
time difference is truncated to seconds before adding it, leading to a
sizable error over time.
Move the truncation to before calculation of the time difference in
order to remove this error. Also maintain the total elapsed time in the
same way in full seconds, to prevent the unsigned 32-bit counter from
wrapping around after about 50 days.
Testing on a VR9 device shows that the reported line uptime now matches
the actual elapsed wall time. The ADSL variant is only compile-tested,
but it should also work as the relevant code is identical.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
(cherry picked from commit db4bf4b968)
Right now, both ltq-adsl-mei and ltq-vdsl-mei are always built, even
when they aren't necessary for the selected variant. This can cause the
build to fail, for example ltq-vdsl-mei doesn't build successfully here
on xway target due to the vectoring callback.
Make these dependencies conditional on the specific package variants,
so they are only built when actually needed.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
(cherry picked from commit 2f484aeff5)
Some users noticed repeated resyncs at random intervals, which go away
when the MEI driver is configured to use polling instead of interrupts.
Debugging shows that this seems to be caused by concurrent calls to
MEI_ReadMailbox (in the interrupt handler) and MEI_WriteMailbox. This
appears to be mostly triggered when there is an interrupt for vectoring
error reports.
In polling mode, calls to MEI_ReadMailbox are protected by the same
semaphore as is used in MEI_WriteMailbox. When interrupts are used,
MEI_WriteMailbox appears to rely on MEI_DisableDeviceInt and
MEI_EnableDeviceInt to provide mutual exclusion with the interrupt
handler. These functions mask/unmask interrupts, and there is an
additional check of the mask in the interrupt handler itself. However,
this is not sufficient on systems with SMP, as the interrupt handler
may be running in parallel, and could already be past the interrupt
mask check at this point.
This adds a lock to the interrupt handler, and also acquires this lock
in MEI_DisableDeviceInt. This should make sure that after a call to
MEI_DisableDeviceInt the interrupt is masked, and the interrupt handler
is either not running, has alread finished its work, or is still before
the interrupt mask check, and is thus going to detect the change.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
(cherry picked from commit 1700424553)
This tells the modem about the WAN MAC address, which is used as source
address for vectoring error reports that are generated by the firmware.
It needs to be set early, as the MEI driver only actually writes the
value to the modem when is in reset state (i.e. the firmware has been
loaded, but connection has not started yet).
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
(cherry picked from commit b35d33c8b8)
This re-enables the vectoring error sample callback and adds a
dependency to the corresponding driver.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
(cherry picked from commit 93f0e1f922)
In order to calculate the required pre-distortion for downstream
vectoring, the vectoring control entity (VCE) at the carrier office
needs error samples from the modem. On Lantiq VR9 modems, error reports
are generated by the firmware, but need to be multiplexed into the data
stream by the driver on the main processor when L2 encapsulation is
selected by the VCE.
This driver provides the necessary callback function, which is called by
the MEI driver after receiving an error report from the firmware.
Originally, it is part of the Lantiq PPA driver, but after a few changes
it also works with the PTM driver used in OpenWrt. The direct call to
ndo_start_xmit needs to be replaced, as the PTM driver relies on locks
from the kernel. Instead dev_queue_xmit is used, which is called from a
work queue, as it is not safe to call from an interrupt handler.
Additional changes include fixes to support recent kernel versions and
a change of the used interface from ptm0 to dsl0.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
(cherry picked from commit f872b96609)
A GPIO assert is required to reset the system. Otherwise, the system
will hang on reboot.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit a2817ce96f17db3a5af77837ae5733b47182ae0d)
Tested in a DGS-1210-28 F3, both triggering failsafe and reboot.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit b85f59b726442621efb95153ff60b8767723feca)
Add NVRAM quirks script for the bcm53xx target. Split NVRAM quirks for the
bcm47xx and bcm53xx targets. Move clear partialboot NVRAM quirk for Linksys
EA9500 here. Add set wireless LED behaviour quirk for Asus RT-AC88U.
Use boot() instead of start() as nvram commands are meant to be executed
only once, at boot.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
(cherry picked from commit f4e219fd5e)
Asus RT-AC88U is an AC3100 router featuring 9 Ethernet ports over the
integrated Broadcom and the external Realtek switch.
Hardware info:
* Processor: Broadcom BCM4709C0KFEBG dual-core @ 1.4 GHz
* Switch: BCM53012 in BCM4709C0KFEBG & external RTL8365MB
* DDR3 RAM: 512 MB
* Flash: 128 MB (ESMT F59L1G81LA-25T)
* 2.4GHz: BCM4366 4×4 2.4/5G single chip 802.11ac SoC
* 5GHz: BCM4366 4×4 2.4/5G single chip 802.11ac SoC
* Ports: 8 Ports, 1 WAN Ports
Flashing instructions:
* Boot to CFE Recovery Mode by holding the reset button while power-on.
* Connect to the router with an ethernet cable.
* Set IPv4 address of the computer to 192.168.1.2 subnet 255.255.255.0.
* Head to http://192.168.1.1.
* Reset NVRAM.
* Upload the OpenWrt image.
CFE bootloader may reject flashing the image due to image integrity check.
In that case, follow the instructions below.
* Rename the OpenWrt image as firmware.trx.
* Run a TFTP server and make it serve the firmware.trx file.
* Run the URL below on a browser or curl.
http://192.168.1.1/do.htm?cmd=flash+-noheader+192.168.1.2:firmware.trx+flash0.trx
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
[rmilecki: mark BROKEN until we sort out nvram & CFE recovery]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 72b9b721d7)
The ZyXEL GS1900-24E is a 24 port gigabit switch similar to other GS1900
switches.
Specifications
--------------
* Device: ZyXEL GS1900-24E
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB Macronix MX25L12835F
* RAM: 128 MiB DDR2 SDRAM Nanya NT5TU128M8GE
* Ethernet: 24x 10/100/1000 Mbps
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
24 ethernet port link/activity LEDs (green, SoC controlled)
* Buttons: 1 "RESET" button on front panel
* Switch: 1 Power switch on rear of device
* Power 120-240V AC C13
* UART: 1 serial header (JP2) with populated standard pin connector on
the left side of the PCB.
Pinout (front to back):
+ Pin 1 - VCC marked with white dot
+ Pin 2 - RX
+ Pin 3 - TX
+ PIn 4 - GND
Serial connection parameters: 115200 8N1.
Installation
------------
OEM upgrade method:
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware
* Select the HTTP radio button
* Select the Active radio button
* Use the browse button to locate the
realtek-rtl838x-zyxel_gs1900-24e-initramfs-kernel.bin
file and select open so File Path is updated with filename.
* Select the Apply button. Screen will display "Prepare
for firmware upgrade ...".
*Wait until screen shows "Do you really want to reboot?"
then select the OK button
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/realtek-rtl838x-zyxel_gs1900-24e-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-24E is a dual-partition device, you want to keep the OEM
firmware on the backup partition for the time being. OpenWrt can only boot
from the first partition anyway (hardcoded in the DTS). To make sure we are
manipulating the first partition, issue the following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24e-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24e-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
Signed-off-by: Raylynn Knight <rayknight@me.com>
(cherry picked from commit b515ad10a6)
Using nvmem-cells to set the MAC address for a DBDC device results in
both PHY devices using the same MAC address. This in turn will result in
multiple BSSes using the same BSSID, which can cause various problems.
Use the hotplug script for the EAP615-Wall instead to avoid this.
Fixes: a1b8a4d7b3 ("ramips: support TP-Link EAP615-Wall")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-By: Andrew Powers-Holmes <aholmes@omnom.net>
(cherry picked from commit ce90ba1f31)
mkimage limits the length of the file paths in can deal with to 256
characters. Turns out that in automated builds by asu we break this
limit, so increase it to 1024 characters.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 3fbf9689b6)
2f793a4 lua: add optional path filter to objects() method
2bebf93 ubusd: handle invoke on event object without data
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 1521d5f453)
2e1fcf4 netifd: fix hwmode for 60g band
39ef9fe interface-ip: fix memory corruption bug when using jail network namespaces
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 7eb83b2015)
557c98e init: selinux: don't relabel virtual filesystems
7a00968 init: only relabel rootfs if started from initramfs
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 4cbc26b212)
4b4849cf5e5a interface-ip: unify host and proto route handling
507c0513d176 interface-ip: add support for excluding interfaces in host route lookup
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 24cc341fdc)
56cb2d4 nas: add decoding of cell_id
9a9019a uqmi: wms - added storage to read text messages
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 51c442c265)
Aruba deploys a BDF in the root filesystem, however this matches the one
used for the DK04 reference board.
The board-specific BDFs are built into the kernel. The AP-365 shows
sinificant degraded performance with increased range when used with the
reference BDF.
Replace the BDF with the one extracted from Arubas kernel.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit b21b98627d)
Currently malta configures the first Ethernet device as WAN interface.
If it finds a second one it will configure it as LAN.
This commit reverses it to match armvirt and x86. If there is only one
network device it will be configured as LAN device now. If we find two
network devices the 2. one will be WAN.
If no board.d network configuration is given it will be configured in
package/base-files/files/etc/board.d/99-default_network
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[minor typos]
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit fb1ba92202)
210991d fw4: prefer /dev/stdin if available
4e5e322 fw4: make `fw4 restart` behavior more robust
221040e ruleset: emit time ranges when both start and stop times are specified
30a7d47 fw4: fix datetime parsing
fb9a6b2 ruleset: correct mangle_output chain type
6dd2617 fw4: fix logic flaw in testing hw flow offloading support
c7c9c84 fw4: ensure that negative bitcounts are properly translated
c4a78ed fw4: fix typo in emitted set types
Fixes: #9764, #9923, #9927, #9935, #9955
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit a7ddef6ef1)
d996047 syntax: adjust number literal parsing and string to number conversion
9efbe18 lib: refactor `uc_int()`
da3f089 lib: rework uc_index() implementation
559029e ci: make jobs faster during pull request testing
Fixes: #9923
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(backported from commits 251e70c887 and
7f998088f0)
The label MAC address for DIR-825 Rev. B1 is the WAN address located
at 0xffb4 in `caldata`, which equals LAN MAC at 0xffa0 incremented by 1.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
(cherry picked from commit 4bed263af7)
Update the name of for the Ubiquiti NanoBeam M5 to match the
auto-generated one at runtime. Otherwise sysupgrade complains about
mismatching device names.
This also required renaming the DTS.
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
(cherry picked from commit 21a3ce97d5)
Ubiquiti NanoBeam M5 devices are CPE equipment for customer locations
with one Ethernet port and a 5 GHz 300Mbps wireless interface.
Specificatons:
- Atheros AR9342
- 535 MHz CPU
- 64 MB RAM
- 8 MB Flash
- 1x 10/100 Mbps Ethernet with passive PoE input (24 V)
- 6 LEDs of which four are rssi
- 1 reset button
- UART (4-pin) header on PCB
Notes:
The device was supported by OpenWrt in ar71xx.
Flash instructions (web/ssh/tftp):
Loading the image via ssh vias a stock firmware prior "AirOS 5.6".
Downgrading stock is possible.
* Flashing is possible via AirOS software update page:
The "factory" ROM image is recognized as non-native and then installed correctly.
AirOS warns to better be familiar with the recovery procedure.
* Flashing can be done via ssh, which is becoming difficult due to legacy
keyexchange methods.
This is an exempary ssh-config:
KexAlgorithms +diffie-hellman-group1-sha1
HostKeyAlgorithms ssh-rsa
PubkeyAcceptedKeyTypes ssh-rsa
User ubnt
The password is ubnt.
Connecting via IPv6 link local worked best for me.
1. scp the factory image to /tmp
2. fwupdate.real -m /tmp/firmware_image_file.bin -d
* Alternatively tftp is possible:
1. Configure PC with static IP 192.168.1.2/24.
2. Enter the rescue mode. Power off the device, push the reset button on
the device (or the PoE) and keep it pressed.
Power on the device, while still pushing the reset button.
3. When all the leds blink at the same time, release the reset button.
4. Upload the firmware image file via TFTP:
tftp 192.168.1.20
tftp> bin
tftp> trace
Packet tracing on.
tftp> put firmware_image.bin
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
(cherry picked from commit 4cd3ff8a79)
The MikroTik hAP (product code RB951Ui-2nD) is
an indoor 2.4Ghz AP with a 2 dBi integrated antenna built around the
Atheros QCA9531 SoC.
Specifications:
- SoC: Atheros QCA9531
- RAM: 64 MB
- Storage: 16 MB NOR - Winbond 25Q128FVSG
- Wireless: Atheros QCA9530 (SoC) 802.11b/g/n 2x2
- Ethernet: Atheros AR934X switch, 5x 10/100 ports,
10-28 V passive PoE in port 1, 500 mA PoE out on port 5
- 8 user-controllable LEDs:
· 1x power (green)
· 1x user (green)
· 4x LAN status (green)
· 1x WAN status (green)
· 1x PoE power status (red)
See https://mikrotik.com/product/RB951Ui-2nD for more details.
Notes:
The device was already supported in the ar71xx target.
Flashing:
TFTP boot initramfs image and then perform sysupgrade. Follow common
MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Maciej Krüger <mkg20001@gmail.com>
(cherry picked from commit 5ce64e0646)
The MikroTik RB952Ui-5ac2nD (sold as hAP ac lite) is an indoor 2.4Ghz
and 5GHz AP/router with a 2 dBi integrated antenna.
See https://mikrotik.com/product/RB952Ui-5ac2nD for more details.
Specifications:
- SoC: QCA9533
- RAM: 64MB
- Storage: 16MB NOR
- Wireless: QCA9533 802.11b/g/n 2x2 / QCA9887 802.11a/n/ac 2x2
- Ethernet: AR934X switch, 5x 10/100 ports,
10-28 V passive PoE in port 1, 500 mA PoE out on port 5
- 6 user-controllable LEDs:
- 1x user (green)
- 5x port status (green)
Flashing:
TFTP boot initramfs image and then perform sysupgrade. The "Internet"
port (port number 1) must be used to upload the TFTP image, then
connect to any other port to access the OpenWRT system.
Follow common MikroTik procedure as in
https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
(cherry picked from commit 2bd33e8626)
c22eeef fw4: support negative CIDR bit notation
628d791 hotplug: reliably handle interfaces with ubus zone hints
d005293 fw4: store zone associations from ubus in statefile as well
b268225 fw4: filter non hw-offload capable devices when resolving lower devices
57984e0 fw4: always resolve lower flowtable devices
7782017 tests: fix mocked `fd.read("line")` api
72b196d config: remove restictions on DHCPv6 allow rule
f0cc317 fw4: refactor family selection for forwarding rules
b0b8122 treewide: use modern syntax
05995f1 fw4: fix emitting device jump rules for family restricted zones
b479815 fw4: fix family auto-selection for config nat rules
2816a82 ruleset: ensure that family-agnostic ICMP rules cover ICMPv6 as well
2379c3d tests: add test coverage for zone family selection logic
Fixes: #5066, #9611, #9765, #9854
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit 2df17604a4)
This release comes with a security fix related to c_rehash. OpenWrt
does not ship or use it, so it was not affected by the bug.
There is a fix for a possible crash in ERR_load_strings() when
configured with no-err, which OpenWrt does by default.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit 7a5ddc0d06)
This is mostly a bug fix release, including two that were already
patched here:
- 300-fix-SSL_get_verify_result-regression.patch
- 400-wolfcrypt-src-port-devcrypto-devcrypto_aes.c-remove-.patch
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit 73c1fe2890)
Hardware specs:
SoC: Qualcomm IPQ8065 (dual core Cortex-A15)
RAM: 512 MB DDR3
Flash: 256 MB NAND, 32 MB NOR
WiFi: QCA9983 2.4 GHz, QCA9984 5 GHz
Switch: QCA8337
Ethernet: 5x 10/100/1000 Mbit/s
USB: 1x USB 3.0 Type-A
Buttons: WPS, Reset
Power: 12 VDC, 2.5 A
Ethernet ports:
1x WAN: connected to eth2
4x LAN: connected via the switch to eth0 and eth1
(eth0 is disabled in OEM firmware)
MAC addresses (OEM and OpenWrt):
fw_env @ 0x00 d4:ab:82:??:??:?a LAN (eth1)
fw_env @ 0x06 d4:ab:82:??:??:?b WAN (eth2)
fw_env @ 0x0c d4:ab:82:??:??:?c WLAN 2.4 GHz (ath1)
fw_env @ 0x12 d4:ab:82:??:??:?d WLAN 5 GHz (ath0)
fw_env @ 0x18 d4:ab:82:??:??:?e OEM usage unknown (eth0 in OpenWrt)
OID d4:ab:82 is registered to:
ARRIS Group, Inc., 6450 Sequence Drive, San Diego CA 92121, US
More info:
https://openwrt.org/inbox/toh/arris/tr4400_v2
IMPORTANT:
This port requires moving the 'fw_env' partition prior to first boot to
consolidate 70% of the usable space in flash into a contiguous partition.
'fw_env' contains factory-programmed MAC addresses, SSIDs, and passwords.
Its contents must be copied to 'rootfs_1' prior to booting via initramfs.
Note that the stock 'fw_env' partition will be wiped during sysupgrade.
A writable 'stock_fw_env' partition pointing to the old, stock location
is included in the port to help rolling back this change if desired.
Installation:
- Requires serial access and a TFTP server.
- Fully boot stock, press ENTER, type in:
mtd erase /dev/mtd21
dd if=/dev/mtd22 bs=128K count=1 | mtd write - /dev/mtd21
umount /config && ubidetach -m 23 && mtd erase /dev/mtd23
- Reboot and interrupt U-Boot by pressing a key, type in:
set mtdids 'nand0=nand0'
set mtdparts 'mtdparts=nand0:155M@0x6500000(mtd_ubi)'
set bootcmd 'ubi part mtd_ubi && ubi read 0x44000000 kernel && bootm'
env save
- Setup TFTP server serving initramfs image as 'recovery.bin', type in:
set ipaddr 192.168.1.1
set serverip 192.168.1.2
tftpboot recovery.bin && bootm
- Use sysupgrade to install squashfs image.
This port is based on work done by AmadeusGhost <amadeus@jmu.edu.cn>.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
[add 5.15 changes for 0069-arm-boot-add-dts-files.patch]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit f8b0010dfb)
The ZyXEL GS1900-16 is a 16 port gigabit switch similar to other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-16
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB Macronix MX25L12835F
* RAM: 128 MiB DDR2 SDRAM Nanya NT5TU128M8HE
* Ethernet: 16x 10/100/1000 Mbps
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
16 ethernet port link/activity LEDs (green, SoC controlled)
* Buttons: 1 "RESET" button on front panel
* Power 120-240V AC C13
* UART: 1 serial header (J12) with populated standard pin connector on
the right back of the PCB.
Pinout (front to back):
+ Pin 1 - VCC marked with white dot
+ Pin 2 - RX
+ Pin 3 - TX
+ PIn 4 - GND
Serial connection parameters: 115200 8N1.
Installation
------------
OEM upgrade method:
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware
* Select the HTTP radio button
* Select the Active radio button
* Use the browse button to locate the
realtek-generic-zyxel_gs1900-16-initramfs-kernel.bin
file amd select open so File Path is update with filename.
* Select the Apply button. Screen will display "Prepare
for firmware upgrade ...".
*Wait until screen shows "Do you really want to reboot?"
then select the OK button
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/realtek-generic-zyxel_gs1900-16-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-16 is a dual-partition device, you want to keep the OEM
firmware on the backup partition for the time being. OpenWrt can only boot
from the first partition anyway (hardcoded in the DTS). To make sure we are
manipulating the first partition, issue the following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-16-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-16-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
Signed-off-by: Raylynn Knight <rayknight@me.com>
[removed duplicate patch title, align RAM specification]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 580723e86a)
SoC: Atheros AR7161
RAM: DDR 128 MiB (hynix h5dU5162ETR-E3C)
Flash: SPI-NOR 8 MiB (mx25l6406em2i-12g)
WLAN: 2.4/5 GHz
2.4 GHz: Atheros AR9220
5 GHz: Atheros AR9223
Ethernet: 4x 10/100/1000 Mbps (Atheros AR8021)
LEDs/Keys: 2/2 (Internet + System LED, Mesh button + Reset pin)
UART: RJ45 9600,8N1
Power: 12 VDC, 1.0 A
Installation instruction:
0. Make sure you have latest original firmware (3.7.11.4)
1. Connect to the Serial Port with a Serial Cable RJ45 to DB9/RS232
(9600,8N1)
screen /dev/ttyUSB0 9600,cs8,-parenb,-cstopb,-hupcl,-crtscts,clocal
2. Configure your IP-Address to 192.168.1.42
3. When device boots hit spacebar
3. Configure the device for tftpboot
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.42
saveenv
4. Reset the device
reset
5. Hit again the spacebar
6. Now load the image via tftp:
tftpboot 0x81000000 INITRAMFS.bin
7. Boot the image:
bootm 0x81000000
8. Copy the squashfs-image to the device.
9. Do a sysupgrade.
https://openwrt.org/toh/netgear/wndap360
The device should be converted from kmod-owl-loader to nvmem-cells in the
future. Nvmem cells were not working. Maybe ATH9K_PCI_NO_EEPROM is missing.
That is why this commit is still using kmod-owl-loader. In the future
the device tree may look like this:
&ath9k0 {
nvmem-cells = <&macaddr_art_120c>, <&cal_art_1000>;
nvmem-cell-names = "mac-address", "calibration";
};
&ath9k1 {
nvmem-cells = <&macaddr_art_520c>, <&cal_art_5000>;
nvmem-cell-names = "mac-address", "calibration";
};
&art {
...
cal_art_1000: cal@1000 {
reg = <0x1000 0xeb8>;
};
cal_art_5000: cal@5000 {
reg = <0x5000 0xeb8>;
};
};
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit 88527294cd)
This commit adds support for the TP-Link Deco M4R (it can also be M4,
TP-Link uses both names) v1 and v2. It is similar hardware-wise to the
Archer C6 v2. Software-wise it is very different. V2 has a bit different
layout from V1 but the chips are the same and the OEM firmware is the same
for both versions.
Specifications:
SoC: QCA9563-AL3A
RAM: Zentel A3R1GE40JBF
Wireless 2.4GHz: QCA9563-AL3A (main SoC)
Wireless 5GHz: QCA9886
Ethernet Switch: QCA8337N-AL3C
Flash: 16 MB SPI NOR
Flashing:
The device's bootloader only accepts images that are signed using
TP-Link's RSA key, therefore this way of flashing is not possible. The
device has a web GUI that should be accessible after setting up the device
using the app (it requires the app to set it up first because the web GUI
asks for the TP-Link account password) but for unknown reasons, the web
GUI also refuses custom images.
There is a debug firmware image that has been shared on the device's
OpenWrt forum thread that has telnet unlocked, which the bootloader will
accept because it is signed. It can be used to transfer an OpenWrt image
file over to the device and then be used with mtd to flash the device.
Pre-requisites:
- Debug firmware.
- A way of transferring the file to the router, you can use an FTP server
as an example.
- Set a static IP of 192.168.0.2/255.255.255.0 on your computer.
- OpenWrt image.
Installation:
- Unplug your router and turn it upside down. Using a long and thin object
like a SIM unlock tool, press and hold the reset button on the router and
replug it. Keep holding it until the LED flashes yellow.
- Open 192.168.0.1. You should see the bootloader recovery's webpage.
Choose the debug firmware that you downloaded and flash it. Wait until the
router reboots (at this stage you can remove the static IP).
- Open a terminal window and connect to the router via telnet (the primary
router should have a 192.168.0.1 IP address, secondary routers are
different).
- Transfer the file over to the router, you can use curl to download it
from the internet (use the insecure flag and make sure your source accepts
insecure downloads) or from an FTP server.
- The router's default mtd partition scheme has kernel and rootfs
separated. We can use dd to split the OpenWrt image file and flash it with
mtd:
dd if=openwrt.bin of=kernel.bin skip=0 count=8192 bs=256
dd if=openwrt.bin of=rootfs.bin skip=8192 bs=256
- Once the images are ready, you have to flash the device using mtd
(make sure to flash the correct partitions or you may be left with a
hard bricked router):
mtd write kernel.bin kernel
mtd write rootfs.bin rootfs
- Flashing is done, reboot the device now.
Signed-off-by: Foica David <superh552@gmail.com>
(cherry picked from commit 063e9047cc)
this adds the mediatek,led_source dts binding for
Asus RT-AC1200 devices' dtsi, for correct switch LED
behavior.
The dts-binding is introduced in commit:
65dc9e0980
Without this, we only have constantly very fast
blinking LEDs, which don't react on any traffic or
LAN events at all.
Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
(cherry picked from commit 771ea6f2e3)
Specifications:
SoC: MediaTek MT7621
RAM: 256 MB
Flash: 32 MB
WiFi: MediaTek MT7915E
Switch: 1 WAN, 4 LAN (Gigabit)
Ports: 1 USB 3.0
Buttons: Reset, WPS
LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB
Power: DC 12V 1A tip positive
Installation:
Download and flash the manufacturer's built OpenWRT image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWRT image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings. The force upgrade may need to be checked
due to differences in router naming conventions.
Recovery:
Loads only signed manufacture firmware due to bootloader RSA verification
serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
connect to any lan ethernet port
power on the device while holding the reset button
wait at least 8 seconds before releasing reset button for image to
download
Signed-off-by: Alessio Prescenzo <alessioprescenzo@gmail.com>
[ensure unique wireless MAC, fix GPIO pingroup]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 4a8eaa5c7c)
The SERCOMM NA502s is a smart home gateway manufactured by SERCOMM and sold
under different brands (among others, A1 Telekom Austria SmartHome Premium
Gateway). It has multi-protocol radio support in addition to LAN and WiFi.
Note: BLE and audio are currently unsupported.
Specifications
--------------
- MT7621ST 880MHz, Single-Core, Dual-Thread
- MT7603EN 2.4GHz WiFi
- MT7662EN 5GHz WiFi + BLE
- 128MiB NAND
- 256MiB DDR3 RAM
- SD3503 ZWave Controller
- EM357 Zigbee Coordinator
- Telit UMTS module
- Rechargeable battery
- speaker and microphone
MAC address assignment
----------------------
LAN MAC is read from the config partition, WiFi 2.4GHz is LAN+2 and matches
the OEM firmware. WiFi 5GHz with LAN+1 is an educated guess since the
OEM firmware does not enable 5GHz WiFi.
Installation
------------
Attach serial console, then boot the initramfs image via TFTP.
Once inside OpenWrt, run sysupgrade -n with the sysupgrade file.
Attention: The device has a dual-firmware design. We overwrite kernel2,
since kernel1 contains an automatic recovery image.
If you get NAND ECC errors and are stuck with bad eraseblocks, try to
erase the mtd partition first with
mtd unlock ubi
mtd erase ubi
This should only be needed once.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
(cherry picked from commit 9ee6ac00c4)
The Wavlink WL-WN533A8 is an AC3000 router with 5 gigabit ethernet ports
and one USB 3.0 port.
It's also known as Wavlink QUANTUM T8.
Hardware
--------
SoC: Mediatek MT7621A
RAM: 128MB (Nanya NT5CB64M16GP-EK)
FLASH: 16MB NOR (GigaDevice GD25Q127CSIG3)
ETH:
- 5x 10/100/1000 Mbps Ethernet (4x LAN + 1x WAN)
WIFI:
- 1x MT7615DN (2x 2x2:2) 2.4GHz and 5GHz DBDC
- 1x MT7615NE (4x4:4) 5GHz
- 8 external antennas
BTN:
- 1x Reset button
- 1x WPS button
- 1x Turbo button
- 1x Touchlink button
- 1x ON/OFF switch
LEDS:
- 1x Red led (system status)
- 1x Blue led (system status)
- 7x Blue leds (wifi led + 5 ethernet ports + power)
USB:
- 1x USB 3.0 port
UART:
- 57600-8-N-1
J4
Everything works correctly.
Installation
------------
Flash the initramfs image in the OEM firmware interface
(http://192.168.10.1/update.shtml).
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.
(Procedure tested on fw M33A8.V5030.190716 and M33A8.V5030.201204)
Restore OEM Firmware
--------------------
Flash the firmware update available online directly from LUCI.
You can download it from:
https://www.wavlink.com/en_us/firmware/details/f2d247ecba.html
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.
Notes
-----
1) Router mac addresses:
LAN XX:XX:XX:XX:XX:63 (factory @ 0xe006)
WAN XX:XX:XX:XX:XX:64 (factory @ 0xe000)
WIFI 2G/5G XX:XX:XX:XX:XX:65 (factory @ 0x04)
WIFI 5G XX:XX:XX:XX:XX:66 (factory @ 0x8004)
LABEL XX:XX:XX:XX:XX:65
In OEM firmware the DBDC wifi interfaces have these mac addresses:
2G) 82:XX:XX:XX:XX:65
5G) 80:XX:XX:XX:XX:65
While in OpenWrt the addresses are:
2G) 80:XX:XX:XX:XX:65
5G) 02:XX:XX:XX:XX:65
2) radio0 will show as 2G/5G interface but only 2G is really usable.
3) There is just one wifi led for all wifi interfaces.
It currently shows only the radio0 GHz wifi activity.
4) My unit was shipped with M33A8.V5030.190716 firmware which contains
the http://192.168.10.1/webcmd.shtml page. Entering "telnetd" in
the input box it will start the telnet daemon. Now you can access
the telnet console on port 2323 with these credentials:
username: admin2860
password: admin
5) The M33A8.V5030.201204 firmware version, doesn't contain anymore the
webcmd.shtml page. If your router is shipped with a previous firmware
version and you want to back it up, you can follow the back up
procedure of the WS-WN583A6.
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
(cherry picked from commit 32e6942d72)
Most of the definitions for WN531A6 will be shared with WN533A8 in a
future commit, so put them in a shared DTSI.
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
(cherry picked from commit 57b6dcd826)
TP-Link RE650 v2 is largely similar to v1 that
is already supported by OpenWrt. Notable differences
is differnt SPI Flash - 8 MB instead of 16 MB
(from cFeon instead of Winbond) and a different
configuration of PCIE connections to wifi chips.
Otherwise it's largely the same product as v1
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 8 MB - cFeon QH64A-104HIP
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART pinout - GND, RX, TX, labeled in the middle of the PCB,
requires soldering because they're not through holes.
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re650-v2-squashfs-factory.bin
from the RE650 web interface.
TFTP recovery to stock firmware:
I didn't try recovering back to the stock firmware, however,
if there is such process for other RExxx devices, it seems like
it could be similar here.
Signed-off-by: Marcin Gordziejewski <openwrt@flicksfix.com>
(cherry picked from commit 39799974a3)
There are two versions which are identical apart from the enclosure:
YunCore AX820: indoor ceiling mount AP with integrated antennas
YunCore HWAP-AX820: outdoor enclosure with external (N) connectors
Hardware specs:
SoC: MediaTek MT7621DAT
Flash: 16 MiB SPI NOR
RAM: 128MiB (DDR3, integrated)
WiFi: MT7905DAN+MT7975DN 2.4/5GHz 2T2R 802.11ax
Ethernet: 10/100/1000 Mbps x2 (WAN/PoE+LAN)
LED: Status (green)
Button: Reset
Power: 802.11af/at PoE; DC 12V,1A
Antennas: AX820(indoor): 4dBi internal; HWAP-AX820(outdoor): external
Flash instructions:
The "OpenWRT support" version of the AX820 comes with a LEDE-based
firmware with proprietary MTK drivers and a luci webinterface and
ssh accessible under 192.168.1.1 on LAN; user root, no password.
The sysupgrade.bin can be flashed using luci or sysupgrade via ssh,
you will have to force the upgrade due to a different factory name.
Remember: Do *not* preserve factory configuration!
MAC addresses as used by OEM firmware:
use address source
2g 44:D1:FA:*:0b Factory 0x0004 (label)
5g 46:D1:FA:*:0b LAA of 2g
lan 44:D1:FA:*:0c Factory 0xe000
wan 44:D1:FA:*:0d Factory 0xe000 + 1
The wan MAC can also be found in 0xe006 but is not used by OEM dtb.
Due to different MAC handling in mt76 the LAA derived from lan is used
for 2g to prevent duplicate MACs when creating multiple interfaces.
Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
(cherry picked from commit 4891b86538)
Includes image support for new TP-Link devices:
ddc3e00e314d tplink-safeloader: add TP-Link EAP265 HD support
ceea1a7fe56e tplink-safeloader: add TP-Link Deco M4R v1 and v2 support
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 0f207ade12)
This backports a patch from Linux 5.10.116 to fix a compile problem
introduced in 5.10.114.
drivers/usb/phy/phy-generic.c could not find
devm_regulator_get_exclusive().
Fixes: 8592df67f4 ("kernel: bump 5.10 to 5.10.114")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 7400adae8d)
Some revisions of the FRITZ!7530 use a Toshiba NAND with 8 bit ECC in
contrast to the Macronix NAND with 4 bit ECC. This removes the hardcoded
ECC strength and step size as set in qcom-ipq4019.dtsi, thus relying on the
kernel NAND detection routines to correclty set up the ECC parameters.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
(cherry picked from commit f167f4a9a4)
The Toshiba TC58NVG0S3HTA00 is detected with 64 byte OOB while the flash
has 128 byte OOB. This adds a static NAND ID entry to correct this.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
(cherry picked from commit 0bc794a668)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
From Andreas Böhler:
"Some revisions of the FRITZ!7530 use a Toshiba NAND with 8 bit ECC
in contrast to the Macronix NAND with 4 bit ECC.".
Uboot needs to know this in order to have a chance to load from
the NAND.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 057bac2e1f)
ZTE MF286A and MF286R feature a "power switch override" GPIO in stock
firmware as means to prevent power interruption during firmware update,
especially when used with internal battery.
To ensure that this GPIO is
properly driven as in stock firmware, configure it with userspace GPIO
switch.
It was observed that on some units, the modem would not be
restarted together with the board itself on reboot, this should help
with that as well.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit 1fabeeb799)
On GL-AR300M Series GPIO17 described as I2C SDA in Device Tree.
Because of GPIO_OUT_FUNCTION4 register was not initialized on start,
GPIO17 was uncontrollable, it always in high state. According to QCA9531
documentation, default setting of GPIO17 is SYS_RST_L. In order to make
GPIO17 controllable, it should write value 0x00 on bits [15:8] of
GPIO_OUT_FUNCTION4 register, located at 0x1804003C address.
Signed-off-by: Ptilopsis Leucotis <PtilopsisLeucotis@yandex.com>
(cherry picked from commit 57efdd6a2d)
Do not reset the RTL930x SerDes on link changes, instead set up
the SDS with internal PHYs for the SFP+ ports only.
This fixes the 8 1GBit ports on the Zyxel XGS1250 which
do not work without this patch.
A complete SerDes reset was performed on all SerDes links. For copper
1Gbit ports, this is commonly a single XGMII link to an RTL8218D. There
is however no support for setting up the XGMII link on RTL9300/RTL9310,
thereby wiping the (RX/TX) setup done by u-boot and breaking the 1GBit
ports. No SerDes reset should be done for these links.
The handling of SGMII/HiSGMII, 1000BX or 10GR links is actually entirely
different. All these modes need to be suitably RX calibrated and the
pre- main and post- amplifiers set up properly for TX.
The 10GBit SFP+ fiber links are recalibrated instead of reset, which
e.g. is necessary when someone pulls a module out and puts another in.
This makes swapping out 10GBit fiber modules possible. 1GBit modules are
not yet supported, nor any modules with an internal phy.
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
[rewrite commit message based on discussion]
Link: http://lists.infradead.org/pipermail/openwrt-devel/2022-May/038623.html
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit d1b824650f)
This fixes a bug where frames sent to the switch itself were
flooded to all ports unless the MAC address of the CPU-port
was learned otherwise.
Tested-by: Wenli Looi <wlooi@ucalgary.ca>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
[fix code formatting]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 98bb26f9f7)
This fixes a well known "LZMA ERROR 1" error, reported previously on
numerous of similar devices.
Fixes: #9824
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
(cherry picked from commit 064e7e57b4)
There are many ways to add external RTC to Raspberry Pi boards. Let's
include support for this for the whole target and while at it, sort
features alphabetically.
Fixes: #9594
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
(cherry picked from commit ff09905a46)
This series also contains other improvement for hardware flow offload support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 0f029b3d2b)
Remove restrictions on source and destination addresses, which aren't
specified on RFC8415, and for some reason in openwrt are configured
to allow both link-local and ULA addresses.
As cleared out in issue #5066 there are some ISPs that use Gloabal
Unicast addresses, so fix this rule to allow them.
Fixes: #5066
Signed-off-by: Tiago Gaspar <tiagogaspar8@gmail.com>
[rebase onto firewall3, clarify subject, bump PKG_RELEASE]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit 65258f5d60)
Remove forgotten redundant selinuxenabled call and skip the whole
thing in case $IPKG_INSTROOT is set as labels are anyway applied only
later on in fakeroot when squashfs is created.
Fixes: 6d7272852e ("base-files: add missing $IPKG_INSTROOT to restorecon call")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 7b07c3cff5)
try to clean up some labeling inconsistencies
iwinfo loose ends
ucode loose ends
Makefile: adjust mintesttgt (adds blockmount/blockd)
nftables: reads inherited netifd pipe
ucode: reads inherited netifd pipes
mountroot: fowner
sandbox: writes inherited dropbear pipes
unbound related to /tmp/etc/ssl
unbound loose ends
adds a sslconftmpfile for /tmp/etc/ssl
README: maintain a wish list in the README
iwinfo: netifd forgot write
gptfdisk loose ends
iwinfo: netifd wpad reads/writes inherited netifd fifo files
netifd (mac80211.sh) executes iwinfo
luci: executes wireguard
luci-cgi: audits xtables execute access
rcuhttpd: lists ssl certfile dirs
iwinfo, wifi,nftables usage of ttyd pty if available
urandomseed: seedrng needs cap_sys_admin
iwinfo iwinfo, nftables and some chronyd rules related to ntp nts server
nftables, wifi and adds iwinfo skel
nftables, rpcd, ucode
nftables, ucode and seedrng ucode, fw3/nftables, luci
adds ucode skel and some fw3/nftables related
urandomseed: some seedrng rules
fw3 adds some support for fw4
urandomseed: /etc/seedrng is for seed.credit
hotplugcal: runs ucode which is interpreter like
adds a nftables skeleton and makes xtables optional
agent: allow all agents to write inherited dropbear pipes
urandomseed: this seems to be replaced by seedrng
kmodloader: label /etc/modules.conf kmodloader.conffile
Revert "shelexecfile: remove auditallow rule"
Makefile: sort the modules to process by secilc
Moves back to git.defensec.nl
unbound odhcpd (ip) reads net proc
tcp dump
shelexecfile: remove auditallow rule
rrd.cil: fixes indent
Target rddtool from cgi-io instead of runnit it without transition
rrd.cil related
rrd, rpcd, cgiio clean ups related to luci-app-statistics
Rules for rrd files and luci-statistics
unboundcontrol ordering
Several missing permissions
blockmount, dnsmasq, hotplugcall, rpcd, unbound
adds mctp_socket (linux 5.15)
ip: forgot tc-tiny type transition to go along with the fc spec
ip: adds a fc spec for tc-tiny (called by sqm)
adds ttyACM fc spec and various assorted loose ends
.gitattributes: do not export the github workflows
workflow use selinux 3.3
project moved back to https://git.defensec.nl/selinux-policy.git
Signed-off-by: Dominick Grift <dominick.grift@defensec.nl>
(cherry picked from commit 4379457098)
Update to overlooked v2 version of Dominick Grift's patch.
Fixes: 5109bd164c ("base-files: address sed in-place without SELinux awareness")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 6d7272852e)
After the switch to pre-calibration, ath10k would fail to initialize
the PCIE Wi-Fi on the GL-B200 as follows:
ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
ath10k_pci 0000:01:00.0: qca9888 hw2.0 target 0x01000000 chip_id 0x00000000 sub 0000:0000
[...]
ath10k_pci 0000:01:00.0: failed to fetch board data for bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=GL-B2200 from ath10k/QCA9888/hw2.0/board-2.bin
ath10k_pci 0000:01:00.0: failed to fetch board-2.bin or board.bin from ath10k/QCA9888/hw2.0
ath10k_pci 0000:01:00.0: failed to fetch board file: -12
ath10k_pci 0000:01:00.0: could not probe fw (-12)
Repackage the BDF file after renaming relevant fields and files to
allow for the Wi-Fi interface to start again.
Fixes: 80d34d9d59 ("ipq40xx: document pcie wifi chip on the GL.Inet GL-B2200")
CC: Christian Lamparter <chunkeey@gmail.com>
CC: Robert Marko <robimarko@gmail.com>
Reviewed-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
(cherry picked from commit e3f9af4fb6)
Add USB power control in DTS for GL.iNet models:
- AR300M;
- AR300M-Ext;
- AR300M16;
- AR300M16-Ext.
Signed-off-by: PtilopsisLeucotis <PtilopsisLeucotis@yandex.com>
(cherry picked from commit 6e9c814022)
In commit 7e614820a8 ("mpc85xx: add support for Extreme Networks
WS-AP3825i"), we borrowed a recipe convention from apm821xx for device
tree blob padding. Unfortunately, in the apm821xx target, the image
recipes name the device tree blob differently, meaning that in
mpc85xx, the padded dtb is never consumed.
Change the definition of `Build/dtb` so that it outputs the padded dtb
to the correct location for it to be consumed.
Also, rename the recipe to `Build/pad-dtb`, so it is clear we
are building and padding the device tree blob.
This change fixes Github issue #9779 [1].
[1]: https://github.com/openwrt/openwrt/issues/9779
Fixes: 7e614820a8 ("mpc85xx: add support for Extreme Networks WS-AP3825i")
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
(cherry picked from commit 1d06277407)
targetclean should not remove BUILD_LOG
Fixes: db34b93331 (add a version that can be bumped to force toolchain/target rebuild)
Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
(cherry picked from commit aeaa816cd2)
If logfacility is a path to a file it needs to be r/w mounted in the
sandbox as well for dnsmasq to work.
Reported-by: @iointerrupt
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 2b5fa44f60)
These don't have switches that could be configured using swconfig.
Signed-off-by: Martin Weinelt <hexa@darmstadt.ccc.de>
(cherry picked from commit 089eb02abc)
When adding support to the router's built-in modem, this required
package was omitted, because it was already enabled in the image
configuration in use for testing, and this went unnoticed.
In result, the modem still isn't fully supported in official images.
As it is the primary WAN interface, add the missing package.
Fixes: e02fb42c53 ("comgt: support ZTE MF286R modem")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit 8a1003c598)
The 2.4GHz interface doesn't come up properly with the log showing:
mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)
As seen on other MT7621 boards this is caused by a missing reset GPIO.
The MT7621 dtsi set GPIO 19 as PCIe reset GPIO, which on this board
reset the 5GHz interface on port 0. Add GPIO 8 to the PCIe reset GPIO
list to also reset the 2.4GHz interface on port 1.
Signed-off-by: Alban Bedel <albeu@free.fr>
(cherry picked from commit f953a1a4bf)
Add configuration to use uboot-envtools with the Extreme Networks
WS-AP3825i.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit fb7ff6b027)
The bootloader does seem to not correctly patch in the MAC address for
eth0 / eth1 in some cases. While the root cause is not known, manually
applying the MAC-Address in preinit does not hurt.
Reported-by: Tom Herbers <freifunk@tomherbers.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit c6d52515e0)
The WS-AP3825i uses Atheros PHYs which according to the datasheet
require the reset to be asserted for at least 1 ms.
This fixes broken eth1 upon soft-reboot. eth0 is no affected, as the
ifup / ifdown cycle in preinit prevents this issue from happening when
the system is ready.
Reported-by: Tom Herbers <freifunk@tomherbers.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 8b3c313515)
e14b099 syntax: implement support for ES6 template literals
111cf06 vm: stop executing bytecode on return of nested calls
33f1e0b treewide: move json-c compat shims into internal header file
e0e9431 vm: move unhandled exception reporting out of `uc_vm_execute_chunk()`
2b59140 vm: fix callframe double free on unhanded exceptions
7d7e950 main: abort when failing to load a preload library
1032a67 lib: let `json()` accept input objects implementing `read()` method
5ee68d5 fs: implement `fs.readfile()` and `fs.writefile()`
df6b861 ci: debian: change path before attempting to invoke Git operations
dfaf05a ci: debian: automatically update changelog from Git tag
34f3c45 ci: fix YAML syntax of Debian workflow
e956bcf fs: fix off-by-one in fs.dirname() function
6fc4b6c .gitignore: fix overmatching patterns, blacklist cram .venv
7c2e082 build: remove legacy json-c check
77942af build: add polyfills for older libjson-c versions
0b4aaa3 CI: build Debian package
f404285 debian: Add package definition
a37f654 types: fix escape sequence encoding of high byte values in JSON strings
aae5312 Update README.md
8134e25 build: fix symlink install target
87c7296 treewide: replace some leftover "utpl" occurrences, update .gitignore
7d27ad5 build: only stage ucc symlink if compile support is enabled
171402f lib: add date and time related functions
8b5dc60 lib: provide API function to obtain stdlib function implementations
eb0d2f1 main: turn ucode into multicall executable
28ee7e1 uloop: add support for tasks
753dea9 CI: build on macOS
668c5c0 lib: add argument position support (`%m$`) to `sprintf()` and `printf()`
ab46fdf treewide: remove legacy json-c include directives
b8f49b1 tests: 21_regex_literals: generalize syntax error test case
fd2e5e7 tests: 16_sort: fix logic flaw exposed on OS X
2c71bf2 tests: run_tests.sh: pass dummy value to `-T` flag
55c4a90 lib: disallow zero padding for %s formats
0d05cb5 tests: run_tests.sh: use greadlink if available
271e520 resolv: make OS X compatible
d13c320 fs: avoid Linux specific sys/sysmacros.h include on OS X
33397a3 uloop: use execvp() on OS X
bafdc8f lib: add naive sigtimedwait() stub for OS X
ada1585 build: consolidate CMakeLists.txt and cover OS X deviations
befbb69 include: add OS X compatible endian.h header
49838a8 include: rename include guards to avoid clashes with system headers
91f65de nl80211: add missing attributes and correct some attribute flags
b4a1fd5 lib: adjust require(), render() and include() raw mode semantics
4618807 main: rework CLI frontend
73dcd78 lib: fix potential integer underflow on empty render output
c402551 vm: fix crash on object literals with non-string computed properties
efe8a02 syntax: support add new operators
078d686 ubus: add event support
6c66c83 ubus: refactor error and argument handling
1cb04f9 ubus: add object publishing, notify and subscribe support
0e85974 uloop: clear errno before integer conversion attempts
05bd7ed types: treat resource type prototypes as GC roots
a2a26ca lib: introduce uloop binding
6b6d01f vm: release this context on exception in managed method call
1af23a9 tests: fix proto() testcase
4ce69a8 fs: implement access(), mkstemp(), file.flush() and proc.flush()
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(backported from commits cef3e6a69c,
0400774a10 and
c59704334c)
Remove '0x' prefix from pstore node in dts, just like it was done
for the device tree used by Linux on MT7622.
This change is done in preparation to update U-Boot to 2022.04.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 810b48e793)
Adresses of device tree nodes are typically noted without the '0x'
prefix. While having the '0x' prefix doesn't hurt when using Linux,
more recent versions of U-Boot will add a duplicate ramoops node as a
simple string compare is used to check if the node is already present.
Remove the '0x' prefix to avoid the kernel warning resulting from
U-Boot adding a dupplicate pstore/ramoops node.
See also https://lists.denx.de/pipermail/u-boot/2022-April/481810.html
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit fc245338d6)
MPLS feature symbols are normally only set when kmod-mpls is enabled, but the
CONFIG_MPLS symbol they depend on could also have been selected by openvswitch
instead
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit 92add80414)
Both legacy iptables and nftables require nf-log modules for rule logging,
so move them into a separate package both firewall implementations can
depend on.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit bea01fa57f)
OrayBox X3A is a 2.4/5GHz dual band AC router, based on MediaTek MT7621.
Specification:
* SoC: MT7621
* RAM: DDR3 128 MiB
* Flash: 16 MiB NOR (XM25Q128)
* Wi-Fi: (single chip hosting both 2.4G and 5G)
* 2.4GHz: MT7615
* 5GHz: MT7615
* Ethernet: 3x 1000Mbps
* Switch: MT7530
* LED:
* Ethernet LEDs: On the back of the router, hardware-controlled.
* Status LEDs: One "pixel-like" RGB LED in the front of the router,
which is actually made up of 3 individual LEDs (with
dedicated GPIO pins) with the color of Red, Green,
and Blue.
The OEM firmware only lights up one color at a time to
indicate status, but that's very boring, and the colors
actually look great when combined, so I've improvised a
little and made them indicate netdev activities.
My test results:
GPIO 13/14/15
000 white (actually more like bright green or cyan
because the brightness of the green LED is
higher than red and blue)
001 bright purple
010 bright green
011 red
100 bright cyan
101 blue
110 green
111 off
Flash Layout:
0x0000000-0x0030000 : "u-boot"
0x0030000-0x0040000 : "u-boot-env"
0x0040000-0x0050000 : "factory"
0x0050000-0x0f50000 : "firmware"
/*0x0f50000 to 0x0fe0000 is undefined, same as OEM firmware*/
0x0fe0000-0x0ff0000 : "bdinfo"
0x0ff0000-0x1000000 : "reserve"
MAC address:
MAC Source Description Fix
A0:CX:XX:BX:XX:0D BDINFO_9 LAN(LABEL) DTS
A0:CX:XX:BX:XX:0E BDINFO_9 + 1 WAN DTS
A2:CX:XX:BX:XX:0F FACTORY_4 WIFI2G DTS
A2:CX:XX:CX:XX:0F SETBIT 7 (FACTORY_4 + 0x100000) WIFI5G HOTPLUG
A6:CX:XX:BX:XX:0F N/A WIFI2G_CLIENT N/A
A6:DX:XX:BX:XX:0F N/A WIFI5G_CLIENT N/A
Stock dmesg:
https://pastebin.com/2t2jwLdf
Stock Dumps:
https://pastebin.com/LDLxSWX3
Installation via SSH (does not void your warranty):
1. -----UNLOCK SSH-----
1.1 Set computer IP to DHCP mode, load 'http://10.168.1.1/cgi-bin/luci' in
your browser. Password is 'admin'.
1.2 Click the "备份且导出" (backup and export) button, and download the
config file.
1.3 Open the downloaded file with 7zip, navigate to '/etc/config/'.
1.4 Edit the file './system'. Change the '0' into '1' under
"config sys 'ssh'".
1.5 Save the file.
1.6 Upload the file by clicking the "导入且恢复" (import and recover)
button. The router will automatically reboot.
2. -----FLASH THE OPENWRT FIRMWARE-----
2.1 Use any scp tool to upload the 'sysupgrade' firmware to the '/tmp/'
folder to your router. It should be root@10.168.1.1 and the password
is 'admin'.
2.2 SSH into the router, also root@10.168.1.1 and the password is 'admin'.
2.3 **IMPORTANT** Type command 'dd if=/dev/mtd3 of=/tmp/firmware.bin', to
backup the stock firmware. Since the OEM does not provide firmware
download on their website, this is the only way to get it.
2.3 **ALSO IMPORTANT** Use any scp tool to download your backed-up stock
firmware from '/tmp/' to your local drive. Then you'd better use a hex
reading tool to have a rough look at it to make sure nothing is
corrupt. Or u can just back up again and cross check the MD5.
2.4 Type command 'mtd write /tmp/XXX.bin firmware', and it should flash
the firmware.
2.5 Verify that nothing went wrong. If you're confident, type 'reboot' and
reboot the router.
Revert to stock firmware:
1. load stock firmware using mtd (make sure u have a backup).
Signed-off-by: Ray Wang <raywang777@foxmail.com>
(cherry picked from commit 9a750aae62)
The ZyXEL GS1900-24HP v1 is a 24 port PoE switch with two SFP ports,
similar to the other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-24HP v1
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB
* RAM: Winbond W9751G8KB-25 64 MiB DDR2 SDRAM
* Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps
* LEDs:
* 1 PWR LED (green, not configurable)
* 1 SYS LED (green, configurable)
* 24 ethernet port link/activity LEDs (green, SoC controlled)
* 24 ethernet port PoE status LEDs
* 2 SFP status/activity LEDs (green, SoC controlled)
* Buttons:
* 1 "RESET" button on front panel (soft reset)
* 1 button ('SW1') behind right hex grate (hardwired power-off)
* PoE:
* Management MCU: ST Micro ST32F100 Microcontroller
* 6 BCM59111 PSE chips
* 170W power budget
* Power: 120-240V AC C13
* UART: Internal populated 10-pin header ('J5') providing RS232;
connected to SoC UART through a TI or SIPEX 3232C for voltage
level shifting.
* 'J5' RS232 Pinout (dot as pin 1):
2) SoC RXD
3) GND
10) SoC TXD
Serial connection parameters: 115200 8N1.
Installation
------------
OEM upgrade method:
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware > Management
* If "Active Image" has the first option selected, OpenWrt will need to be
flashed to the "Active" partition. If the second option is selected,
OpenWrt will need to be flashed to the "Backup" partition.
* Navigate to Maintenance > Firmware > Upload
* Upload the openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-initramfs-kernel.bin
file by your preferred method to the previously determined partition.
When prompted, select to boot from the newly flashed image, and reboot
the switch.
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-squashfs-sysupgrade.bin
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs
image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-24HP v1 is a dual-partition device, you want to keep the
OEM firmware on the backup partition for the time being. OpenWrt can
only be installed in the first partition anyway (hardcoded in the
DTS). To ensure we are set to boot from the first partition, issue the
following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x81f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-squashfs-sysupgrade.bin
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
[Add info on PoE hardware to commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit a5ac8ad0ba)
The Sophos AP100, AP100C, AP55, and AP55C are dual-band 802.11ac access
points based on the Qualcomm QCA9558 SoC. They share PCB designs with
several devices that already have partial or full support, most notably the
Devolo DVL1750i/e.
The AP100 and AP100C are hardware-identical to the AP55 and AP55C, however
the 55 models' ART does not contain calibration data for their third chain
despite it being present on the PCB.
Specifications common to all models:
- Qualcomm QCA9558 SoC @ 720 MHz (MIPS 74Kc Big-endian processor)
- 128 MB RAM
- 16 MB SPI flash
- 1x 10/100/1000 Mbps Ethernet port, 802.3af PoE-in
- Green and Red status LEDs sharing a single external light-pipe
- Reset button on PCB[1]
- Piezo beeper on PCB[2]
- Serial UART header on PCB
- Alternate power supply via 5.5x2.1mm DC jack @ 12 VDC
Unique to AP100 and AP100C:
- 3T3R 2.4GHz 802.11b/g/n via SoC WMAC
- 3T3R 5.8GHz 802.11a/n/ac via QCA9880 (PCI Express)
AP55 and AP55C:
- 2T2R 2.4GHz 802.11b/g/n via SoC WMAC
- 2T2R 5.8GHz 802.11a/n/ac via QCA9880 (PCI Express)
AP100 and AP55:
- External RJ45 serial console port[3]
- USB 2.0 Type A port, power controlled via GPIO 11
Flashing instructions:
This firmware can be flashed either via a compatible Sophos SG or XG
firewall appliance, which does not require disassembling the device, or via
the U-Boot console available on the internal UART header.
To flash via XG appliance:
- Register on Sophos' website for a no-cost Home Use XG firewall license
- Download and install the XG software on a compatible PC or virtual
machine, complete initial appliance setup, and enable SSH console access
- Connect the target AP device to the XG appliance's LAN interface
- Approve the AP from the XG Web UI and wait until it shows as Active
(this can take 3-5 minutes)
- Connect to the XG appliance over SSH and access the Advanced Console
(Menu option 5, then menu option 3)
- Run `sudo awetool` and select the menu option to connect to an AP via
SSH. When prompted to enable SSH on the target AP, select Yes.
- Wait 2-3 minutes, then select the AP from the awetool menu again. This
will connect you to a root shell on the target AP.
- Copy the firmware to /tmp/openwrt.bin on the target AP via SCP/TFTP/etc
- Run `mtd -r write /tmp/openwrt.bin astaro_image`
- When complete, the access point will reboot to OpenWRT.
To flash via U-Boot serial console:
- Configure a TFTP server on your PC, and set IP address 192.168.99.8 with
netmask 255.255.255.0
- Copy the firmware .bin to the TFTP server and rename to 'uImage_AP100C'
- Open the target AP's enclosure and locate the 4-pin 3.3V UART header [4]
- Connect the AP ethernet to your PC's ethernet port
- Connect a terminal to the UART at 115200 8/N/1 as usual
- Power on the AP and press a key to cancel autoboot when prompted
- Run the following commands at the U-Boot console:
- `tftpboot`
- `cp.b $fileaddr 0x9f070000 $filesize`
- `boot`
- The access point will boot to OpenWRT.
MAC addresses as verified by OEM firmware:
use address source
LAN label config 0x201a (label)
2g label + 1 art 0x1002 (also found at config 0x2004)
5g label + 9 art 0x5006
Increments confirmed across three AP55C, two AP55, and one AP100C.
These changes have been tested to function on both current master and
21.02.0 without any obvious issues.
[1] Button is present but does not alter state of any GPIO on SoC
[2] Buzzer and driver circuitry is present on PCB but is not connected to
any GPIO. Shorting an unpopulated resistor next to the driver circuitry
should connect the buzzer to GPIO 4, but this is unconfirmed.
[3] This external RJ45 serial port is disabled in the OEM firmware, but
works in OpenWRT without additional configuration, at least on my
three test units.
[4] On AP100/AP55 models the UART header is accessible after removing
the device's top cover. On AP100C/AP55C models, the PCB must be removed
for access; three screws secure it to the case.
Pin 1 is marked on the silkscreen. Pins from 1-4 are 3.3V, GND, TX, RX
Signed-off-by: Andrew Powers-Holmes <andrew@omnom.net>
(cherry picked from commit 6f1efb2898)
This patch adds support for the MikroTik RouterBOARD 962UiGS-5HacT2HnT (hAP ac)
Specifications:
- SoC: QCA9558
- RAM: 128 MB
- Flash: 16 MB SPI
- 2.4GHz WLAN: 3x3:3 802.11n on SoC
- 5GHz WLAN: 3x3:3 802.11ac on QCA9880 connected via PCIe
- Switch: 5x 1000/100/10 on QCA8337 connected via RGMII
- SFP cage: connected via SGMII (tested with genuine & generic GLC-T)
- USB: 1x type A, GPIO power switch
- PoE: Passive input on Ether1, GPIO switched passthrough to Ether5
- Reset button
- "SFP" LED connected to SoC
- Ethernet LEDs connected to QCA8337 switch
- Green WLAN LED connected to QCA9880
Not working:
- Red WLAN LED
Installation:
TFTP boot initramfs image and then perform sysupgrade. Follow common
MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
(cherry picked from commit c2140e32ce)
Hardware specifications:
SoC: MT7628DAN MIPS_24KEc@580MHz 2.4G-n 2x2
WiFi: MT7613BEN 5G-ac 160MHz 2x2
Switch: 4x100M built-in SoC
Flash: 16MB W25Q128JVSQ SPI-NOR
DRAM: 64MB built-in SoC
MAC addresses as verified by OEM firmware:
use address source
Lan/Wan/2G *:60 factory 0x4 (label)
5G *:64 factory 0x8000
Serial console: 57600,8n1
Installation:
Asus windows recovery tool:
install the Asus firmware restoration utility
unplug the router, hold the reset button while powering it on
release when the power LED flashes slowly
specify a static IP on your computer:
IP address: 192.168.1.75
Subnet mask 255.255.255.0
start the Asus firmware restoration utility, specify the factory image
and press upload
do NOT power off the device after OpenWrt has booted until the LED flashing
after flashing OpenWrt, there will be first no 5GHz Wifi available probably,
wait until blinking finishes and do a reboot
TFTP Recovery method:
set computer to a static ip, 192.168.1.75
connect computer to the LAN 1 port of the router
hold the reset button while powering on the router for a few seconds
send firmware image using a tftp client; i.e from linux:
$ tftp
tftp> binary
tftp> connect 192.168.1.1
tftp> put factory.bin
tftp> quit
do NOT power off the device after OpenWrt has booted until the LED flashing
after flashing OpenWrt, there will be first no 5GHz Wifi available probably,
wait until blinking finishes and do a reboot
Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
(cherry picked from commit a4bf562aa7)
This device is from now-defunct BOLT! ISP in Indonesia.
The original firmware is based on mediatek SDK running linux 2.6 or 3.x in later revision.
Specifications:
- SoC: MediaTek MT7621
- Flash: 32 MiB NOR SPI
- RAM: 128 MiB DDR3
- Ethernet: 2x 10/100/1000 Mbps (switched, LAN + WAN)
- WIFI0: MT7603E 2.4GHz 802.11b/g/n
- WIFI1: MT7612E 5GHz 802.11ac
- Antennas: 2x internal, non-detachable
- LEDs: Programmable LEDs: 5 blue LEDs (wlan, tel, sig1-3) and 2 red LEDs (wlan and sig1)
Non-programmable "Power" LED
- Buttons: Reset and WPS
Instalation:
Install from TFTP
Set your PC IP to 10.10.10.3 and gateway to 10.10.10.123
Press "1" when turning on the router, and type the initramfs file name
You also need to solder pin header or cable to J4 or neighboring test points (T19-T21)
Pinouts from top to bottom: GND, TX, RX, VCC (3.3v)
Baudrate: 57600n8
There's also an additional gigabit transformer and RTL8211FD managed by the LTE module on the backside of the PCB.
Signed-off-by: Abdul Aziz Amar <abdulaziz.amar@gmail.com>
(cherry picked from commit 78c3534645)
The Wavlink WL-WN531A3 is an AC1200 router with 5 fast ethernet ports
and one USB 2.0 port.
It's also known as Wavlink QUANTUM D4.
Hardware
--------
SoC: Mediatek MT7628AN
RAM: 64MB
FLASH: 8MB NOR (GigaDevice GD25Q64CSIG3)
ETH:
- 5x 10/100 Mbps Ethernet (4x LAN + 1x WAN)
WIFI:
- 2.4GHz: 1x (integrated in SOC) (2x2:2)
- 5GHz: 1x MT7612E (2x2:2)
- 4 external antennas
BTN:
- 1x Reset button
- 1x WPS button
- 1x Turbo button
- 1x Touchlink button
- 1x ON/OFF switch
LEDS:
- 1x Red led (system status)
- 1x Blue led (system status)
- 7x Blue leds (wifi led + 5 ethernet ports + power)
USB:
- 1x USB 2.0 port
UART:
- 57600-8-N-1
J1
O VCC +3,3V (near lan ports)
o RX
o TX
o GND
Everything works correctly.
Currently there is no firmware update available. Because of this, in
order to restore the OEM firmware, you must firstly dump the OEM
firmware from your router before you flash the OpenWrt image.
Backup the OEM Firmware
-----------------------
The following steps are to be intended for users having little to none
experience in linux. Obviously there are many ways to backup the OEM
firmware, but probably this is the easiest way for this router.
Procedure tested on M31A3.V4300.200420 firmware version.
1) Go to http://192.168.10.1/webcmd.shtml
2) Type the following line in the "Command" input box and then press enter:
mkdir /etc_ro/lighttpd/www/dev; cp /dev/mtd0ro /etc_ro/lighttpd/www/dev/mtd0ro; ls -la /etc_ro/lighttpd/www/dev/mtd0ro
3) After few seconds in the textarea should appear this output:
-rw-r--r-- 1 0 0 8388608 /etc_ro/lighttpd/www/dev/mtd0ro
If your output doesn't match mine, stop reading and ask for
help in the forum.
4) Open in another tab http://192.168.10.1/dev/mtd0ro to download the
content of the whole NOR. If the file size is 0 byte, stop reading
and ask for help in the forum.
5) Come back to the http://192.168.10.1/webcmd.shtml webpage and type:
rm /etc_ro/lighttpd/www/dev/mtd0ro; for i in 1 2 3 4 ; do cp /dev/mtd${i}ro /etc_ro/lighttpd/www/dev/mtd${i}ro; done; ls -la /etc_ro/lighttpd/www/dev/
6) After few seconds, in the textarea should appear this output:
-rw-r--r-- 1 0 0 196608 mtd1ro
-rw-r--r-- 1 0 0 65536 mtd2ro
-rw-r--r-- 1 0 0 65536 mtd3ro
-rw-r--r-- 1 0 0 8060928 mtd4ro
drwxr-xr-x 7 0 0 0 ..
drwxr-xr-x 2 0 0 0 .
If your output doesn't match mine, stop reading and ask for
help in the forum.
7) Open the following links to download the partitions of the OEM FW:
http://192.168.10.1/dev/mtd1rohttp://192.168.10.1/dev/mtd2rohttp://192.168.10.1/dev/mtd3rohttp://192.168.10.1/dev/mtd4ro
If one (or more) of these files are 0 byte, stop reading and ask
for help in the forum.
8) Store these downloaded files in a safe place.
9) Reboot your router to remove any temporary file in ram.
Installation
------------
Flash the initramfs image in the OEM firmware interface
(http://192.168.10.1/update.shtml).
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.
Restore OEM Firmware
--------------------
Flash the "mtd4ro" file you previously backed-up directly from LUCI.
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.
Notes
-----
1) Router mac addresses:
LAN XX:XX:XX:XX:XX:9B (factory @ 0x28)
WAN XX:XX:XX:XX:XX:9C (factory @ 0x2e)
WIFI 2G XX:XX:XX:XX:XX:9D (factory @ 0x04)
WIFI 5G XX:XX:XX:XX:XX:9E (factory @ 0x8004)
LABEL XX:XX:XX:XX:XX:9D
2) There is just one wifi led for both wifi interfaces.
It currently shows only the 2.4 GHz wifi activity.
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
(cherry picked from commit bb505d82ad)
There are various reports on Github and in the forum that this commit
causes multiple problems.
This reverts commit ee6ba216d8.
Fixes: #9420
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit 3e0daca644)
The MikroTik RouterBOARD wAP-2nd (sold as wAP) is a small
2.4 GHz 802.11b/g/n PoE-capable AP.
Specifications:
- SoC: Qualcomm Atheros QCA9533
- Flash: 16 MB (SPI)
- RAM: 64 MB
- Ethernet: 1x 10/100 Mbps (PoE in)
- WiFi: AR9531 2T2R 2.4 GHz (SoC)
- 3x green LEDs (1x lan, 1x wlan, 1x user)
See https://mikrotik.com/product/RBwAP2nD for more info.
Flashing:
TFTP boot initramfs image and then perform sysupgrade. Follow common
MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.
Note: following 781d4bfb39
The network setup avoids using the integrated switch and connects the
single Ethernet port directly. This way, link speed (10/100 Mbps) is
properly reported by eth0.
Signed-off-by: David Musil <0x444d@protonmail.com>
(cherry picked from commit e20de22442)
Move the GPIO extender to the SoC node. Otherwise, the legacy PowerPC
init code will not populate the BUS and thus never probe spi-gpio.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit f0c09d0305)
This patch was accidentally backported from master for kernel 5.15 too.
Remove the version for kernel 5.15 and keep the version for kernel 5.10.
Fixes: 9ab337dfbc ("kernel: backport pgalloc memory leak fix")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Python seems to fail to link to libreadline properly because of this.
Not a fatal error but an error nontheless.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(cherry picked from commit b363f74886)
FRITZ!Box 7360 V2 and FRITZ!Box 7360 SL both use GPIOs 37 (for &phy0)
and GPIO 44 (for &phy1) to control the PHY's reset lines. FRITZ!Box 7362
SL however uses GPIO 45 (for &phy0) and GPIO 44 (for &phy1). Move the
GPIO reset definitions to each individual board .dts and while at it,
fix the GPIOs for the FRITZ!Box 7362 SL.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
(cherry picked from commit 56cd49bdc8)
The modem is based on Marvell PXA1826 and uses ACM+RNDIS interface to
establish connection with custom commands specific to ZTE modems.
Two variants of modems were discovered, some identifying themselves
as "ZTE", and others as plain "Marvell", the chipset manufacturer.
The modem itself runs a fork of OpenWrt inside, which root shell can be
accessed via ADB interface.
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit e02fb42c53)
Some modems expose ttyACM as their control ports, which have the
"device" symlink pointing one level down in sysfs tree. Try to find
network interfaces for them as well, this is commonly used for modems
exposing ACM + RNDIS or ACM + ECM interface combinations.
Co-developed-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit ed7957810c)
Some modems expose multiple network interfaces on the same USB device,
causing the connection setup script to fail, because glob matching in
the detection phase causes 'ls' to output more than one interface name
plus their base directories in sysfs. Avoid that by listing the
directories explicitly and then selecting first available interface.
This is the case for some variants of ZTE MF286R built-in modem, which
exposes both RNDIS and CDC-ECM network interfaces, causing the
connection setup to fail.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit b2940bb8b2)
Add ifname property to UCI, which can be used to override the
autodetected interface name in case the detection fails due to having
none or more than one interface exposed by the modem, which is not
explicitly linked to TTY port. This is needed on certain variants of ZTE
MF286R built-in modem, which exposes both RNDIS and CDC-ECM interfaces
on the modem, on which the automatic detection may select the wrong
network interface.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit a67629bbe2)
This is required to support built-in modem of ZTE MF286R, in addition to
other external modems, such as MF831, MF910, MF920, which refuse to
reconfigure their remote MAC address, even if "locally administered" bit
is set, leading to dropped traffic towards the host. Add a workaround
for that issue already present in cdc_ether to rndis_host driver as
well.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit c99013e242)
Fix wrong CPU OPP for ipq8062. Revision of the SoC added an
extra 25mV for every pvs. Also fix the voltage min/max value
that were wrong.
Reviewed-by: Robert Marko robimarko@gmail.com
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
(cherry picked from commit 3f0d87fd69)
The existing device tree has incorrect definitions for usb3_0 and usb3_1
and the blocks they depend upon: their addresses and interrupts are
swapped. However, their clocks and resets are not. The result is that
the USB blocks are non-functional if only one of them is enabled.
This fix backports the definitions from mainline Linux 5.15 to
OpenWrt's 5.10 dtsi additions. See the relevant mainline code here:
https://github.com/torvalds/linux/blob/v5.17/arch/arm/boot/dts/qcom-ipq8064.dtsi#L1062-L1148
This fix does not break existing ports. But some ports may have enabled
both USB blocks even thought their board only implements one, because
enabling a single USB block would not have worked before this fix.
This means that revisiting all ports of ipq806x devices that implement
a single USB port is advised. This work must be done by maintainers that
can determine which USB block corresponds to the implemented port on
their hardware.
Note that this fix swaps the names of the hardware ports. This is
unfortunate, but will happen anyway when switching to kernel 5.15. Thus,
it is best to do this ASAP, before users get to depend on port names.
It is strongly recommended that this fix is backported to 22.03 before
its release. This will minimize the number of users affected by the port
name swap.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
(cherry picked from commit 284f2c2ae0)
These workarrounds are incomplete and non-functional, and thus not needed.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
(cherry picked from commit 3a4d972d43)
Make it clear, that for `make kernel_{menu,old}config` it's possible to
use only following values for CONFIG_TARGET variable:
* env
* target
* subtarget
* subtarget_target
This should prevent misuse like `make kernel_menuconfig
CONFIG_TARGET=bcm2710` etc.
Keep support for obsolete `platform` and `subtarget_platform` targets
with deprecation notice so this compat stuff could be removed in the
future.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Piotr Dymacz <pepe2k@gmail.com>
(cherry picked from commit 68e672f32d)
Notify external ubus subscribers of received link-measurement reports.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit f6445cfa1a)
Add a ubus method to request link-measurements from connected STAs.
In addition to the STAs address, the used and maximum transmit power can
be provided by the external process for the link-measurement. If they
are not provided, 0 is used as the default value.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 965aa33a18)
Allow external processes to enable advertisement of link-measurement RRM
capability.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 2ca5c3da04)
As the LED controller is working now, we can make good use of the LEDs
now.
- Drop the model-name prefix
- Rename eth0 / eth1 LEDs to LAN1 / LAN2, as they are labeled as such
on the casing
- Enable wired LEDs in userspace
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 9024f1e466)
Image metadata and signature is of no use for images which are included
inside other artifacts (like an SD-card image). Strip them off before
using images in artifacts or stashing them for the ImageBuilder as the
contained signature breaks reproducibility.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 7a256d97d9)
Improvements since the 4.0.38 release are:
- Rename strtoi to strosi (string to signed int). The strtoi
function on BSD does something else (returns an intmax, not
an int)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 08ebc3881d)
mtools recursive copy (mcopy -s ...) is using READDIR(3) to iterate
over the directory entries, hence they end up in the FAT filesystem in
traversal order which breaks reproducibility (rather than being added
to the FAT filesystem in a reproducible order). Implement recursive
copy in gen_image_generic.sh in Shell code instead, as in that way we
can force files to be copied in reproducible order.
Fixes: aece8f5ae8 ("scripts/gen_image_generic.sh: generate reproducible EFI filesystem")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 4d289ae7e6)
Checking whether /sbin/udhcpc is a symbolic link breaks using the
DHCP proto handler inside procd-ujail where bind-mounts are used for
the resolved link. Check whether /sbin/udhcpc is executable instead
to allow using the proto handler for DHCP-provisioned containers.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit c5f113c43f)
Make sure sysupgrade on NAND also works in case of UBI volumes having
index >9. While at it, also make sure UBI device is detected and abort
in case it isn't. Use Shell built-in shorthand ':' instead of 'true'.
Fixes#9708
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 0dbca1b2ba)
Generate FAT filesystem for EFI boot in a reproducible way:
* use '--invariant' option of mkfs.fat
* set timestamps of all files to SOURCE_DATE_EPOCH
* make sure files are ordered locale-independent
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit aece8f5ae8)
Set fixed timestamp for kernel other files in /boot filesystem.
This should help making x86 *combined* images reproducible.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 068ea2cde0)
Use ARMv8 Crypto Extensions for AES, ghash and sha256.
This results in a 16 times speed gain in speed for aes-128-ctr, 17x in
aes-128-gcm, and 9 times in sha256.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit c9c2b01b84)
Specification:
- QCA9533 (650 MHz), 64 or 128MB RAM, 16MB SPI NOR
- 2x 10/100 Mbps Ethernet, with 802.3at PoE support (WAN)
- 2T2R 802.11b/g/n 2.4GHz
Flash instructions:
If your device comes with generic QSDK based firmware, you can login
over telnet (login: root, empty password, default IP: 192.168.188.253),
issue first (important!) 'fw_setenv' command and then perform regular
upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download
image to the device, SSH server is not available):
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin
In case your device runs firmware with YunCore custom GUI, you can use
U-Boot recovery mode:
1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with
'tftp' image renamed to 'upgrade.bin'
2. Power the device with reset button pressed and release it after 5-7
seconds, recovery mode should start downloading image from server
(unfortunately, there is no visible indication that recovery got
enabled - in case of problems check TFTP server logs)
Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
(cherry picked from commit a05dcb0724)
Specification:
- QCA9563 (775MHz), 128MB RAM, 16MB SPI NOR
- 2T2R 802.11b/g/n 2.4GHz
- 2T2R 802.11n/ac 5GHz
- 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port)
LED for 5 GHz WLAN is currently not supported as it is connected directly
to the QCA9882 radio chip.
Flash instructions:
If your device comes with generic QSDK based firmware, you can login
over telnet (login: root, empty password, default IP: 192.168.188.253),
issue first (important!) 'fw_setenv' command and then perform regular
upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download
image to the device, SSH server is not available):
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin
In case your device runs firmware with YunCore custom GUI, you can use
U-Boot recovery mode:
1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with
'tftp' image renamed to 'upgrade.bin'
2. Power the device with reset button pressed and release it after 5-7
seconds, recovery mode should start downloading image from server
(unfortunately, there is no visible indication that recovery got
enabled - in case of problems check TFTP server logs)
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
(cherry picked from commit c91df224f5)
Changes:
new features:
- qsort_r function (POSIX-future)
- pthread_getname_np extension function
- hard float on SPE FPU for powerpc-sf
- SEEK_DATA and SEEK_HOLE exposed in unistd.h (Linux extensions)
compatibility:
- free now preserves errno (POSIX-future requirement)
- setjmp is declared explicitly with returns_twice for non-GCC compilers
- macro version of isascii is no longer defined for C++
- dynamic linker now tolerates zero-length LOAD segments
- epoll_[p]wait is now a cancellation point
- pwd/grp functions no longer fail on systems without AF_UNIX support
- POSIX TZ parsing is stricter to allow more names to fallback to files
- NULL is now defined as nullptr when used in C++11 or later
- gettext now accepts null pointer as argument
bugs fixed:
- old regression in wcwidth of Hangul combining (vowel/final) letters
- duplocale used wrong malloc when malloc was replaced (1.2.2 regression)
- fmaf rounded wrong on archs without FE_TOWARDZERO (all softfloat archs)
- popen didn't honor requirement not to leak other popen pipe fds to child
- aligned_alloc and variants crashed on allocation failure
- dl_iterate_phdr reported incorrect module TLS pointers
- mishandling of some inputs in acoshf and expm1f and functions using them
- potentially wrong-sign zero in cproj functions at infinity
- multiple bugs in legacy function cuserid
- minor posix_spawn file actions API conformance issues
- pthread_setname_np fd leak
- out-of-bound read in zoneinfo handling with distant-past times
- out-of-tree builds lacked generated debug cfi for x86 asm
arch-specific bugs fixed:
- powerpc (32-bit) struct shmid_ds layout was wrong for some fields
- time64 struct layout was wrong in sound ioctl fallback (32-bit archs)
In addition it contains the following improvements:
* protect stack canary from leak via read-as-string by zeroing second byte
* fix excessively slow TLS performance on some mips models
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
Tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
(cherry picked from commit 685ae2687b)
The correct readid method is SPINAND_READID_METHOD_OPCODE_ADDR.
Signed-off-by: Felix Matouschek <felix@matouschek.org>
(cherry picked from commit 3711aee56d)
This updates mac80211 to version 5.15.33-1 which is based on kernel
5.15.33.
The removed patches were applied upstream.
This new release contains many fixes which were merged into the upstream
Linux kernel.
This also contains the following new drivers which are needed for ath11k:
* net/qrtr/
* drivers/bus/mhi/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 3aa96efa24)
Fixes two high-severity vulnerabilities:
- CVE-2022-25640: A TLS v1.3 server who requires mutual authentication
can be bypassed. If a malicious client does not send the
certificate_verify message a client can connect without presenting a
certificate even if the server requires one.
- CVE-2022-25638: A TLS v1.3 client attempting to authenticate a TLS
v1.3 server can have its certificate heck bypassed. If the sig_algo in
the certificate_verify message is different than the certificate
message checking may be bypassed.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit e89f3e85eb)
Export SOURCE_DATE_EPOCH to environment so filesystem and image
creation tools will make use of it.
Fixes reproducibility of images generated with the ImageBuilder.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 5cf5dce05a)
As anyway only the default is called now we can as well also just remove
the override for Build/Configure.
Fixes: e2cffbb805 ("arm-trusted-firmware-mediatek: update to 2021-03-10")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit dffad93d3e)
ARM Trusted Firmware builds do not depend on any target libraries as
they are bare-metal builds. However, the compiler aborts due to
-Werror=missing-include-dirs if the include dir doesn't exists and this
can happen when building with parallelisation as that makes it likely
for arm-trusted-firmware-* to be build very early before any of the
libraries which would implicitely create the directory.
Fix this by making sure the include dir exists before building.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 738d44f5ea)
RT-AC2200 is the same device with a different name. The OEM firmwares have the same MD5.
Signed-off-by: Ray Wang <raywang777@foxmail.com>
(cherry picked from commit 3204906569)
These devices only have 6MiB available for firmware, which is not
enough for recent release images, so move these to the tiny target.
Note for users sysupgrading from the previous ath79-generic snapshot
images:
The tiny target kernel has a 4Kb flash erase block size instead
of the generic target's 64kb. This means the JFFS2 overlay partition
containing settings must be reformatted with the new block size or else
there will be data corruption.
To do this, backup your settings before upgrading, then during the
sysupgrade, de-select "Keep Settings". On the CLI, use "sysupgrade -n".
If you forget to do this and your system becomes unstable after
upgrading, you can do this to format the partition and recover:
* Reboot
* Press RESET when Power LED blinks during boot to enter Failsafe mode
* SSH to 192.168.1.1
* Run "firstboot" and reboot
Signed-off-by: Joe Mullally <jwmullally@gmail.com>
Tested-by: Robert Högberg <robert.hogberg@gmail.com>
(cherry picked from commit 44e1e5d153)
Changes:
Duncan Roe (5):
nlmsg: Fix a missing doxygen section trailer
build: doc: "make" builds & installs a full set of man pages
build: doc: get rid of the need for manual updating of Makefile
build: If doxygen is not available, be sure to report "doxygen: no" to ./configure
src: doc: Fix messed-up Netlink message batch diagram
Fernando Fernandez Mancera (1):
src: fix doxygen function documentation
Florian Westphal (1):
libmnl: zero attribute padding
Guillaume Nault (1):
callback: mark cb_ctl_array 'const' in mnl_cb_run2()
Kylie McClain (1):
examples: nfct-daemon: Fix test building on musl libc
Laura Garcia Liebana (4):
examples: add arp cache dump example
examples: fix neigh max attributes
examples: fix print line format
examples: reduce LOCs during neigh attributes validation
Pablo Neira Ayuso (3):
doxygen: remove EXPORT_SYMBOL from the output
include: add MNL_SOCKET_DUMP_SIZE definition
build: libmnl 1.0.5 release
Petr Vorel (1):
examples: Add rtnl-addr-add.c
Stephen Hemminger (1):
examples: rtnl-addr-dump: fix typo
igo95862 (1):
doxygen: Fixed link to the git source tree on the website.
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit c3b7389339)
Changes:
c63f193 bump version to 1.0.2
3cffa84 libnfnetlink: Check getsockname() return code
90ba679 include: Silence gcc warning in linux_list.h
bb4f6c8 Make it clear that this library is deprecated
e46569c Minimally resurrect doxygen documentation
5087de4 libnfnetlink: hide private symbols
62ca426 autogen: don't convert __u16 to u_int16_t
efa1d8e src: Use stdint types everywhere
7a1a07c include: Sync with kernel headers
7633f0c libnfnetlink: initialize attribute padding to resolve valgrind warnings
94b68f3 configure: uclinux is also linux
617fe82 src: get source code license header in sync with current licensing terms
97a3960 build: resolve automake-1.12 warnings
Removed the patch 100-missing_include.patch, libnfnetlink compiles fine
with musl without this patch.
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit aecf088b37)
bh_event_add_var can be called by multiple threads concurrently,
so it shall not use a static char buffer
Signed-off-by: Andrey Erokhin <a.erokhin@inango-systems.com>
(cherry picked from commit 1e991e09b7)
Override python to use the one in host instead of hostpkg. There's no
need to use the latter.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(cherry picked from commit 19f3fcc884)
The host-build of libselinux requires libsepol/host.
Add the libsepol/host to HOST_BUILD_DEPENDS to allow build on hosts
which don't have libsepol installed.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 0d3850dc5a)
Problem exist when dnsmasq is exclusively bind to particular interface.
After reconfiguring or restarting this interface, its index changes, but
dnsmasq uses the old one. When this problem occurs, dnsmasq does not
listen on the correct interface so DHCP does not work, and clients do not
get an IP address. Procd netdev param can be added to restart dnsmasq when
the interface index is changed.
Signed-off-by: Valentyn Datsko <valikk.d@gmail.com>
[combined into a single &&-connected statement]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 76f55e3c3f)
Fixes compilation under musl based distros like Alpine Linux.
Also add pcre/host as a build dependency as it's needed.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(cherry picked from commit abb2683de3)
The sama7 sub target does not have USB support, the feature should not
be activated there. OpenWrt can automatically detect if the target
supports USB by using the scripts/target-metadata.pl script. With the
automatic detection USB support will only get activated on subtargest
which actually support USB like sam9x and sama5.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit f6d566301e)
Remove the configuration options which are building modules for the sub
target configuration.
These kernel modules are not packaged. Kernel options should only be
build as a module when they are selected by a kmod package and not by
setting them to =m in the target kernel configuration.
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 5a84a8764d)
Set LC_ALL=C environment variable when calling 'sort' as the sort
order otherwise depends on the locale set.
Fixes: 56ce110b73 ("scripts: make sure conffiles are sorted")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 1d77dca3b3)
Make sure the timestamp of the root directory of the initramfs is set
to SOURCE_DATE_EPOCH as well.
Fixes: 29d7461d11 ("kernel: set options to make external initramfs reproducible")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 54bcf586b0)
Introduce `sha256_unsigned` which is a checksum of the image _before_ a
signature is attached. This is helpful to compare image reproducibility.
Since the `.sha256sum` file is located in the $(KDIR) folder, switch
$(BIN_DIR) with $(KDIR) to simplify the code. The value of $(BIN_DIR)
itself is not stored inside the resulting JSON file, so it can be
replaced.
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit 8822a8d850)
Make sure xz uses at least 2 threads so compression always runs in
multi-threaded mode as the resulting file in single-threaded mode
differs.
Fixes: 29d7461d11 ("kernel: set options to make external initramfs reproducible")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit fc6a83e63b)
Drop the -processors argument from the mksquashfs4 call, so it will use
all available processors. This dramatically reduces the time to create
squashfs filesystems.
The times below are observed when building an image for my main router,
the WatchGuard Firebox M300 (qoriq target):
Before:
real 4m45,973s
After:
real 0m23,497s
With this commit `mksquashfs` may use more cores than defined via `-j`.
This is the same behaviour as for archive creation of ImageBuilder, SDK
or toolchain. There is no trivial way to limit `mksquashfs` CPU core
usage to the amount of "free" make jobs since two running `mksquashfs`
instances would each run with the total allowed number (-j) of threads.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
[extended reasoning in commit message]
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit df2ae8826c)
It may happen that conffiles are in different order on different builds.
Make sure they have the same order by sorting them.
FIX: #9612
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit 56ce110b73)
A Python script containing an unreproducible path is copied by default.
Remove it before generating the package.
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit 950bd40a27)
The PKG_LICENSE field was missing.
While at it, normalize the Makefile a bit.
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit 839b1ff1fc)
The WatchGuard Firebox M200 and M300 use a Marvell 88e1543 PHY for the
first 3 ethernet ports. This PHY is supported by the Marvell Alaska PHY
driver, so enable it.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit d7eba8059b)
Previously commit openwrt/packages@3abb7cb ("lvm2: Added script and updated Makefile[...]")
couldn't actually work and allow rootfs_data to be stored on a LVM2 as
the necessary kernel modules had not been loaded at this point.
Fix this by loading device-mapper modules early at boot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 82f9ad6ab2)
The first argument for snprintf is the buffer and the 2. one is the
size. Fix the order. This broke the lock application.
Fixes: 9d2b26d5a7 ("busybox: fix busybox lock applet pidstr buffer overflow")
Reported-by: Hartmut Birr <e9hack@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit d80336e1a9)
Kernel setting `/proc/sys/kernel/pid_max` can be set up to 4194304 (7
digits) which will cause buffer overflow in busbox lock patch, this
often happens when running in a rootfs container environment.
This commit enlarges `pidstr` to 12 bytes to ensure a sufficient buffer
for pid number and an additional char '\n'.
Signed-off-by: Qichao Zhang <njuzhangqichao@gmail.com>
(cherry picked from commit 34567750db)
the cache directory should be autom4te.cache in all $(PKG_AUTOMAKE_PATHS)
rather than $(PKG_BUILD_DIR)/autom4te.cache only
Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
(cherry picked from commit 044ca149f3)
Getting rid of shared libraries for hostpkg avoids having to use rpath
hacks to find the library. It also fixes compilation with host glib2
binaries.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(cherry picked from commit f8571749a7)
Avoids having to add rpath to the various packages using it. Also add
PIC to fix compilation as static libraries do not use PIC by default.
Fixes: 1fb099341e ("musl-fts: add host build")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(cherry picked from commit 8a75ed4ba0)
# CONFIG_PSTORE_COMPRESS_DEFAULT="deflate"
this can lead to confusion. Thankfully, in the KConfig
world this setting is still interpreted as disabled.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit de4879c1ae)
This model, also know as "1&1 HomeServer", shares the same features as 7530.
The vendor firmware has artificial software limitations: only 2 of the 4
LAN-Ports are GBit, and the USB-Host is only v2.0.
With OpenWrt, USB is already working at v3.0.
Signed-off-by: Andre Heider <a.heider@gmail.com>
(updated commit message to reflect current state)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit cb6f4be137)
Some configure scripts look for msgfmt and gmsgfmt. As we don't install
the latter, configure might pick up one from staging_dir/hostpkg, and
the other from the host:
checking for msgfmt... /home/stijn/Development/OpenWrt/openwrt/staging_dir/hostpkg/bin/msgfmt
checking for gmsgfmt... /usr/bin/gmsgfmt
This could potentially lead to hard to debug undefined behaviour.
Install a symlink in the host install phase to avoid this.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit 636cb00ecc)
v2022.01 has a regression that broke eMMC usage on most if not all Armada
SoC-s, thus breaking boards like uDPU which use eMMC for storage.
Fix it by backporting a recent upstream patch.
Fixes: 782d4c8306 ("uboot-mvebu: update to version 2022.01")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit a703830806)
The memory leak is fixed by the kernel patches backported in the
previous commit.
This reverts commit 1fa8780056.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit f6cda9f06b)
Backport a fix for the massive memory leak observed in Octeon after
switching to kernel 5.10.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit 9283359bd5)
There is a hard to reproduce, even harder to track down memory leak in
Octeon since kernel 5.10. Mark octeon source-only until it is plugged.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit 1fa8780056)
When upgrading a TP-Link Archer C5 v1 from ar71xx to ath79,
the 5ghz radio stops working because the device path changed.
Same has been done for the Archer C7 before:
commit e19506f206 ("ath79: migrate Archer C7 5GHz radio device paths")
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
(cherry picked from commit c6eb63d48f)
The label has the MAC address of eth0, not the WLAN PHY address. We can
merge the definition back into ar7241_ubnt_unifi.dtsi, as both DTS
derived from it use the same interface for their label MAC addresses
after all.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit aee9ccf5c1)
The tc package does not exits any more, it was split into tc-tiny,
tc-full and tc-bpf. Include tc-bpf by default into realtek images.
This increases the compressed image size by about 232KBytes.
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 34fb36e165)
The realtek target is not a router, but basic device, see DEVICE_TYPE.
The basic device type does not come with firewall by default, see
include/target.mk for details. The realtek target extended
DEFAULT_PACKAGES manually with firewall.
This changes the defaults to take firewall4 and nftables instead of
firewall and iptables. This also adds the additional package
kmod-nft-offload.
The only difference to the router type is the missing ppp,
ppp-mod-pppoe, dnsmasq and odhcpd-ipv6only package.
This increases the compressed image size by about 422KBytes.
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 469030659c)
Do not include the dnsmasq and odhcpd-ipv6only package by default any
more. These services are not needed on a switch. If someone needs this
it is still possible to use opkg or image builder to add them.
This decreases the compressed image size by about 165KBytes.
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 2acebbdcaa)
removes usb-port remains as neither the WAC510 nor the WAC505
come with a USB port. Update the LED properties to phase out
labels and introduce generic node-names as well as adding
the color, function and function-enumerator properties.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 026fda10a5)
This commit replaces patch number 0703 with the upstream accepted
version. This patch requires backporting an additional patch to
avoid conflicts.
The only significant change is the lower maximum MTU. Packets with
lengths over 2400 may be dropped.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
(cherry picked from commit b4970dab6b)
Evaluating the return value of 'json_load' didn't work in the
intended way resulting in PIN status no longer being read on modems
where --get-pin-status doesn't fail.
Fix this by trying --get-pin-status first and checking if pin1_status
field exists in JSON, and if it doesn't try again with
--uim-get-sim-state.
Fixes: #9501
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit ee7cb5e885)
This commit builds on previous efforts to add support
for Sophos devices.
* Add support for Sophos XG 85 with/without wireless
* Add support for Sophos XG 86 with/without wireless
Tested on Sophos XG 85w rev1 and XG 86 rev 1
Signed-off-by: Raylynn Knight <rayknight@me.com>
(cherry picked from commit c7bcbcd492)
Run cpio as well as compressors in such ways that they are generating
reproducible output.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 29d7461d11)
In commit ab143647ef ("kernel: generic: improve FIT partition parser")
part_bits was bumped to 2 in order to allow up to 3 additional FIT
sub-images mapped into sub-partitions.
This change has to be reflected also in our local patch
420-mtd-set-rootfs-to-be-root-dev.patch
which still assumed part_bits==1 for mtdblock devices in case of
CONFIG_FIT_PARTITION=y.
Fixes: #9557
Fixes: ab143647ef ("kernel: generic: improve FIT partition parser")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 13960fb0e0)
* only map filesystems configured in 'loadables'
* allow mapping more than one filesystem (e.g. customization/branding
or localization in addition to rootfs)
* small cleaning here and there
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit ab143647ef)
If the selected boot configuration is stored by U-Boot in '/chosen'
node as 'bootconf' attribute, use that configuration to resolve the
block device used as rootfs. Fall back to use the default configuration
in case 'bootconf' is not present.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 503f3b9f0e)
Store selected boot configuration in '/chosen' node in device tree, so
it can be accessed by Linux (and used for fine-tuning the FIT partition
parser).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit dfc3ea6810)
Shuttle KD20 has NAND flash with 0x20000 (128KiB) erase blocks.
Correctly set that in uboot-envtools as well to allow writing to the
bootloader environment using fw_setenv.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit fa67639513)
In commit 2d03f27f0f ("openwrt-keyring: make opkg use 22.03 usign
key") I've accidentally removed the `endef` keyword, so fix it by adding
it back.
Fixes: 2d03f27f0f ("openwrt-keyring: make opkg use 22.03 usign key")
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
at91/sama7 fails to build due to:
| Asymmetric (public-key cryptographic) key type (ASYMMETRIC_KEY_TYPE) [Y/?] y
| Asymmetric public-key crypto algorithm subtype (ASYMMETRIC_PUBLIC_KEY_SUBTYPE) [Y/?] y
| Asymmetric TPM backed private key subtype (ASYMMETRIC_TPM_KEY_SUBTYPE) [N/m/?] (NEW)
|Error in reading or end of file.
please note that asym_tpm (module) has been removed in 5.17:
<https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=d3cff4a9>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 6387715093)
Modified the radio frequency hardware part of e2600ac c1/c2,
need to cooperate with the modified board.bin file, the device
can work normally.
Signed-off-by: 张 鹏 <sd20@qxwlan.com>
(cherry picked from commit bdc786e82c)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Tel(co Electronics) X1 Pro is preventing ipq40xx generic
from building due to the KERNEL_SIZE.
Whenever bigger kernels are possible, if lzma is supported
is unknown.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 4ce52de450)
The OCEDO Raccoon had significant packet-loss with cables longer than 50
meter. Disabling EEE restores normal operation.
Also change the ethernet config to reduce loss on sub-1G links.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 4551bfd91f)
Required to allow sysupgrades from OpenWrt 19.07.
Closes#7071
Fixes: 98fbf2edc0 ("ath79: move TPLINK_HWID/_HWREV to parent for tplink-safeloader")
Tested-by: J. Burfeind <git@aiyionpri.me>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit 8ba71f1f6f)
When using external targets there is a symlink being created for the
target under target/linux which then becomes dangling under Image
Builder. Fix it by dereferencing the possible symlink.
Tested on IB with external target, ipq40xx and mvebu.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 621f39d1f4)
While it hasn't always been clear whether the "AP" is part of the model
name on the Ubiquiti website, we include it for all other pre-AC
variants (AP Pro and the AP Outdoor+). Add it to the original UniFi AP
as well for consistency.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit dc23df8a8c)
The label has the MAC address of eth0, not the WLAN PHY address.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit 2a02b70499)
uDPU provides a FIT based initramfs, but currently gets stuck after U-boot
starts the kernel at "Starting kernel..".
It is due to the load address being too low, so increase it in order to get
the initramfs booting again.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit 80f21e5336)
uDPU has 2 LM75 compatible temperature sensors, so include the driver for
them by default in order to utilize them.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit a8b2d35903)
Remove "a" character from the first line of patch
738-v5.14-01-net-dsa-qca8k-fix-an-endian-bug-in-qca8k-get-ethtool.patch
Otherwise `git am` fails to apply this patch which is annoying when
trying to do some development / rebasing.
Signed-off-by: Marek Behún <kabel@kernel.org>
(cherry picked from commit f811c33b19)
a20-olinuxino-lime2 is currently having hard time with link detection of
certain 1000Mbit partners due to usage of generic PHY driver, probably
due to following missing workaround introduced in upstream in commit
3aed3e2a143c ("net: phy: micrel: add Asym Pause workaround"):
The Micrel KSZ9031 PHY may fail to establish a link when the Asymmetric
Pause capability is set. This issue is described in a Silicon Errata
(DS80000691D or DS80000692D), which advises to always disable the
capability. This patch implements the workaround by defining a KSZ9031
specific get_feature callback to force the Asymmetric Pause capability
bit to be cleared.
This fixes issues where the link would not come up at boot time, or when
the Asym Pause bit was set later on.
As a20-olinuxino-lime2 has Micrel KSZ9031RNXCC-TR Gigabit PHY since
revision H, so we need to use Micrel PHY driver on those devices.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit ffa1088f63)
Tavis has just reported, that he was recently trying to track down a
reproducible crash in a compressor. Believe it or not, it really was a
bug in zlib-1.2.11 when compressing (not decompressing!) certain inputs.
Tavis has reported it upstream, but it turns out the issue has been
public since 2018, but the patch never made it into a release. As far as
he knows, nobody ever assigned it a CVE.
Suggested-by: Tavis Ormandy <taviso@gmail.com>
References: https://www.openwall.com/lists/oss-security/2022/03/24/1
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit b3aa2909a7)
391a9fbd5ace dns: fix parsing vlan encapsulated protocol
6aeeddbc91ad interface: extend dns filters to cover vlan tagged traffic as well
1ab53d4ca601 bpf: return TC_ACT_UNSPEC to allow other filters to proceed
ca21e729af23 interface: switch to using clsact for filters
5d158f6b3c15 interface: run ingress bpf filter on main device ingress instead of ifb egress
bdfcb11847ce interface: fix duplicated dns filter line
b97405aa632a Revert "ubus: remove dnsmasq subscriber"
8fbaf39dbc95 interface: rework adding/removing filters, do not delete clsact
d7ba5804eae4 interface: replace open-coded ifb-dns string with QOSIFY_DNS_IFNAME
91cf440db9e2 loader: fix use of deprecated functions
57c7817f91c2 qosify: fix dscp values of ubus-added dns host entries
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry-picked from commit af434e0da2)
As the upcoming release will be based on Linux 5.10 only, remove all
kernel configuration as well as patches for Linux 5.4.
There were no targets still actively using Linux 5.4.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 3a14580411)
Also known as the "Xiaomi Router AX3200" in western markets,
but only the AX6S is widely installation-capable at this time.
SoC: MediaTek MT7622B
RAM: DDR3 256 MiB (ESMT M15T2G16128A)
Flash: SPI-NAND 128 MiB (ESMT F50L1G41LB or Gigadevice GD5F1GQ5xExxG)
WLAN: 2.4/5 GHz 4T4R
2.4 GHz: MediaTek MT7622B
5 GHz: MediaTek MT7915E
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531B
LEDs/Keys: 2/2 (Internet + System LED, Mesh button + Reset pin)
UART: Marked J1 on board VCC RX GND TX, beginning from "1". 3.3v, 115200n8
Power: 12 VDC, 1.5 A
Notes:
U-Boot passes through the ethaddr from uboot-env partition,
but also has been known to reset it to a generic mac address
hardcoded in the bootloader.
However, bdata is also populated with the ethernet mac addresses,
but is also typically never written to. Thus this is used instead.
Installation:
1. Flash stock Xiaomi "closed beta" image labelled
'miwifi_rb03_firmware_stable_1.2.7_closedbeta.bin'.
(MD5: 5eedf1632ac97bb5a6bb072c08603ed7)
2. Calculate telnet password from serial number and login
3. Execute commands to prepare device
nvram set ssh_en=1
nvram set uart_en=1
nvram set boot_wait=on
nvram set flag_boot_success=1
nvram set flag_try_sys1_failed=0
nvram set flag_try_sys2_failed=0
nvram commit
4. Download and flash image
On computer:
python -m http.server
On router:
cd /tmp
wget http://<IP>:8000/factory.bin
mtd -r write factory.bin firmware
Device should reboot at this point.
Reverting to stock:
Stock Xiaomi recovery tftp that accepts their signed images,
with default ips of 192.168.31.1 + 192.168.31.100.
Stock image should be renamed to tftp server ip in hex (Eg. C0A81F64.img)
Triggered by holding reset pin on powerup.
A simple implementation of this would be via dnsmasq's
dhcp-boot option or using the vendor's (Windows only)
recovery tool available on their website.
Signed-off-by: Richard Huynh <voxlympha@gmail.com>
(cherry picked from commit 9f9477b275)
Some units of the Xiaomi Redmi Router AX6S/Xiaomi Router AX3200 contain this part.
Signed-off-by: Richard Huynh <voxlympha@gmail.com>
(cherry picked from commit 4177de10df)
The maintainer-tools.git script still defaults to `http` while
eveyrthing moved over to `https`. This commit switches VERSION_REPO
again back to encrypted connections.
Signed-off-by: Paul Spooren <mail@aparcar.org>
about:The OpenWrt project relies on volunteers. While we appreciate feature requests, we might lack the manpower to handle them. Ideally, you get familiar with the codebase and attempt to contribute the feature yourself. We recommend to post in the forum, as this is the most likely place to receive feedback on feature requests.
- name:OpenWrt community
url:https://openwrt.org/contact
about:Consider reaching out to our community to get help. OpenWrt is a complex software project with many pitfalls; there is a good chance someone can help you solve your issue in no time.
- name:OpenWrt documentation
url:https://openwrt.org/docs/start
about:The OpenWrt documentation contains a lot of valuable information.
If your device is supported, please follow the **Info** link to see install
instructions or consult the support resources listed below.
##
An advanced user may require additional or specific package. (Toolchain, SDK, ...) For everything else than simple firmware download, try the wiki download page:
* [OpenWrt Wiki Download](https://openwrt.org/downloads)
## Development
To build your own firmware you need a GNU/Linux, BSD or macOS system (case
To build your own firmware you need a GNU/Linux, BSD or MacOSX system (case
sensitive filesystem required). Cygwin is unsupported because of the lack of a
echo"$(if $(CONFIG_TARGET_INITRAMFS_FORCE),CONFIG_INITRAMFS_FORCE=y,# CONFIG_INITRAMFS_FORCE is not set)">>$(LINUX_DIR)/.config
else
echo"# CONFIG_INITRAMFS_FORCE is not set">>$(LINUX_DIR)/.config
endif
echo"$(if $(CONFIG_TARGET_INITRAMFS_COMPRESSION_NONE),CONFIG_INITRAMFS_COMPRESSION_NONE=y,# CONFIG_INITRAMFS_COMPRESSION_NONE is not set)">>$(LINUX_DIR)/.config
echo-e"$(if $(CONFIG_TARGET_INITRAMFS_COMPRESSION_GZIP),CONFIG_INITRAMFS_COMPRESSION_GZIP=y\nCONFIG_RD_GZIP=y,# CONFIG_INITRAMFS_COMPRESSION_GZIP is not set\n# CONFIG_RD_GZIP is not set)">>$(LINUX_DIR)/.config
echo-e"$(if $(CONFIG_TARGET_INITRAMFS_COMPRESSION_BZIP2),CONFIG_INITRAMFS_COMPRESSION_BZIP2=y\nCONFIG_RD_BZIP2=y,# CONFIG_INITRAMFS_COMPRESSION_BZIP2 is not set\n# CONFIG_RD_BZIP2 is not set)">>$(LINUX_DIR)/.config
echo-e"$(if $(CONFIG_TARGET_INITRAMFS_COMPRESSION_LZMA),CONFIG_INITRAMFS_COMPRESSION_LZMA=y\nCONFIG_RD_LZMA=y,# CONFIG_INITRAMFS_COMPRESSION_LZMA is not set\n# CONFIG_RD_LZMA is not set)">>$(LINUX_DIR)/.config
echo-e"$(if $(CONFIG_TARGET_INITRAMFS_COMPRESSION_LZO),CONFIG_INITRAMFS_COMPRESSION_LZO=y\nCONFIG_RD_LZO=y,# CONFIG_INITRAMFS_COMPRESSION_LZO is not set\n# CONFIG_RD_LZO is not set)">>$(LINUX_DIR)/.config
echo-e"$(if $(CONFIG_TARGET_INITRAMFS_COMPRESSION_XZ),CONFIG_INITRAMFS_COMPRESSION_XZ=y\nCONFIG_RD_XZ=y,# CONFIG_INITRAMFS_COMPRESSION_XZ is not set\n# CONFIG_RD_XZ is not set)">>$(LINUX_DIR)/.config
echo-e"$(if $(CONFIG_TARGET_INITRAMFS_COMPRESSION_LZ4),CONFIG_INITRAMFS_COMPRESSION_LZ4=y\nCONFIG_RD_LZ4=y,# CONFIG_INITRAMFS_COMPRESSION_LZ4 is not set\n# CONFIG_RD_LZ4 is not set)">>$(LINUX_DIR)/.config
echo-e"$(if $(CONFIG_TARGET_INITRAMFS_COMPRESSION_ZSTD),CONFIG_INITRAMFS_COMPRESSION_ZSTD=y\nCONFIG_RD_ZSTD=y,# CONFIG_INITRAMFS_COMPRESSION_ZSTD is not set\n# CONFIG_RD_ZSTD is not set)">>$(LINUX_DIR)/.config
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
