This reverts commit 3442ec5d57.
The device behaviour is reportedly erratic so let's not take chances and
leave this out for now.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Tested with 18.06.0-rc2/ar71xx/generic/tl-wdr4300-v1, image & list
This PR is based on the work of @fewckert[1] with slight improvements.
Add function `manifest` to show the manifest of the produced image,
before actually building it. The manifest contains an orderd list of
package name and version.
This is usefull to check package dependencies but also determine a
unique and reproducible image name before building the package. The
sysupgrade server[2] builds images on request with individual package
selection. To distignish between created images which contain differnt
packages, the EXTRA_IMAGE_NAME is set to a shortend hash of the
manifest's content. So far the image was renamed afterwards as the
manifests content was unknown, however this corrupts the signed
sha256sums. This patch allows a clean solution as to dtermine the
manifest in advance and set the EXTRA_IMAGE_NAME accordingly.
[1]: https://github.com/lede-project/source/pull/1591
[2]: https://github.com/aparcar/attendedsysupgrade-server
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry-picked from commit 869b0d11db)
Qxwlan E750G v8 is based on Qualcomm QCA9344.
Specification:
- 560/450/225 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4G GHz (AR9344)
- 2x 10/100 Mbps Ethernet (PoE support)
- 2x 10/100/1000 Mbps Ethernet
- 7x LED (6 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-48 V)
- UART (J23) and LEDs (J2) headers on PCB
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "sysupgrade" image
and click the upgrade button.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
(cherry picked from commit 53a4502013)
Qxwlan E750A v4 is based on Qualcomm QCA9344.
Specification:
- 560/450/225 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 5G GHz (AR9344)
- 2x 10/100 Mbps Ethernet (one port with PoE support)
- 1x miniPCIe slot (USB 2.0 bus only)
- 7x LED (6 driven by GPIO)
- 1x button (reset)
- 1x DC jack for main power input (9-48 V)
- UART (J23) and LEDs (J2) headers on PCB
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "sysupgrade" image
and click the upgrade button.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
(cherry picked from commit ac03d51a3f)
Qxwlan E558 v2 is based on Qualcomm QCA9558 + AR8327.
Specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 8/16 MB of FLASH (SPI NOR)
- 2T2R 2.4 GHz (QCA9558)
- 3x 10/100/1000 Mbps Ethernet (one port with PoE support)
- 4x miniPCIe slot (USB 2.0 bus only)
- 1x microSIM slot
- 5x LED (4 driven by GPIO)
- 1x button (reset)
- 1x 3-pos switch
- 1x DC jack for main power input (9-48 V)
- UART (JP5) and LEDs (J8) headers on PCB
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "sysupgrade" image
and click the upgrade button.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
(cherry picked from commit b74f63f81d)
@vahid-dan reported a issue with extracting the rpi images with
Gnome's Archive Manager:
"Ubuntu Archive Manager cannot extract the file and it just
throws a general error message: "An error occurred while
extracting files".
<https://forum.lede-project.org/t/corrupted-pre-built-v18-06-0-rc2-image-for-rpi>
@blogic told me to split the single sdcard.img.gz for the RPi
into a sysupgrade and a factory image for all brcm2708 targets.
The factory images will have no metadata attached, this way
these utilities that can't deal with the attached metadata will
not fail for no reason.
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 7516a96011)
When attempting to use any of the functions in network.sh while netifd is
not started yet, the ubus interface dump query will fail with "Not found",
yielding an empty response.
Subsequently, jsonfilter is invoked with an empty string instead of a valid
JSON document, causing it to emit a second "unexpected end of data" error.
This caused the dnsmasq init script to log the following errors during
early boot on some systems:
procd: /etc/rc.d/S19dnsmasq: Command failed: Not found.
procd: /etc/rc.d/S19dnsmasq: Failed to parse json data: unexpected end of data.
Fix the issue by allowing the ubus query to fail with "Not found" but still
logging other failures, and by passing an empty JSON object to jsonfilter
if the interface status cache is empty.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Update to new iwinfo version.
Adds support for channel survey.
Adds ubus support.
Etc.
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit 296ae7ab89)
e59f925 hardware: add device ids for QCA9984, 88W8887 and 88W8964 radios
2a82f87 nl80211: back out early when receiving FAIL-BUSY reply
77c32f0 nl80211: fix code calculating average signal and rate
Signed-off-by: John Crispin <john@phrozen.org>
(cherry picked from commit 20b76c0a5b)
e15c63a375 introduced code that was trying
to register GPIO 1 as both an LED and a button. The OEM source makes it
clear that LED1 is not wired to the SoC GPIOs. GPIO 1 is the reset button.
Furthermore the (green) power led default state should also be defined,
(matching OEM source), and it should be used by diag.sh since it's
currently the only software-controllable LED.
This patch fixes these issues and renames the corresponding #defines for
clarity
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
(cherry picked from commit e99f760235)
On brcm47xx boards, the model ID is the combination of the "boardtype" nvram
variable and an optional supplemental "boardnum" variable while the human
readable model name is usually exposed in the "machine" field of the
/proc/cpuinfo file.
Move the extraction of the board nvram variables and model name string into
the 01_sysinfo file and rework the 01_detect board configuration script to
solely use the prepared sysinfo values without performing own detection
logic.
As a consequence, we can drop the ucidef_set_board_id() and
ucidef_set_model_name() invocations in favor to the generic behaviour
which copies the /tmp/sysinfo/{board_name,model} values into the board.json
"id" and "name" fields respectively.
Since "01_detect" only contains network configuration logic after this
change, move it to "01_network" and rename the contained "detect_by_xxx"
functions to "configure_by_xxx" instead, to avoid potential confusion.
Fixes FS#1576
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit d7d10f2c1e)
That upstream commit caused instability in flash reads. It was reported
but there isn't any proper fix as for now.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 0417b08b06)
Refresh patches
Upstream commits since last bump:
3b6eb19 Log DNSSEC trust anchors at startup.
f3e5787 Trivial comment change.
c851c69 Log failure to confirm an address in DHCPv6.
a3bd7e7 Fix missing fatal errors when parsing some command-line/config options.
ab5ceaf Document the --help option in the french manual
1f2f69d Fix recurrent minor spelling mistake in french manual
f361b39 Fix some mistakes in french translation of the manual
eb1fe15 When replacing cache entries, preserve CNAMES which target them.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
(cherry picked from commit 1e93ef8498)
As dnsmasq is started earlier than netifd usage of network.sh functions
at boottime will fail; therefore don't call at boottime the functions
which construct the dhcp pool/relay info.
As interface triggers are installed the dhcp pool/relay info will be
constructed when the interface gets reported as up by netifd.
At the same time also register interface triggers based on DHCP relay
config.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
(cherry picked from commit 2336b942b3)
Refresh patches and backport upstream to current HEAD:
a997ca0 Fix sometimes missing DNSSEC RRs when DNSSEC validation not enabled.
51e4eee Fix address-dependent domains for IPv6.
05ff659 Fix stupid infinite loop introduced by preceding commit.
db0f488 Handle some corner cases in RA contructed interfaces with addresses changing interface.
7dcca6c Warn about the impact of cache-size on performance.
090856c Allow zone transfer in authoritative mode whenever auth-peer is specified.
cc5cc8f Sane error message when pcap file header is wrong.
c488b68 Handle standard and contructed dhcp-ranges on the same interface.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
(cherry picked from commit fbf475403b)
This fixes kernel hang when booting on BCM4718A1 (& probably BCM4717A1).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 4c1aa64b4d)
The most important is probably regression fix in handling platform
NVRAM. That bug stopped hardware from being properly calibrated breaking
e.g. 5 GHz for Netgear R8000.
Other than that it triggers memory dumps when experiencing firmware
problems which is important for debugging purposes.
Fixes: 2811c97803 ("mac80211: backport brcmfmac firmware & clm_blob loading rework")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit b26214adb5)
40e0931 libubus: pass an empty UBUS_ATTR_DATA block if msg is NULL on invoke
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit 7316515891)
Reduces .ipk size on MIPS from 41.6k to 41.1k
Changes:
30463d0 zones: add interface/subnet bound LOG rules
0e77bf2 options: treat time strings as UTC times
d2bbeb7 firewall3: make reject types selectable by user
aa8846b ubus: avoid dumping interface state with NULL message
Cherry picked and squashed from commits:
a3f2451fba firewall: update to latest git HEAD
433d71e73e fw3: update to latest git HEAD
ef96d1e34a firewall: compile with LTO enabled
1e83f775a3 firewall3: update to latest git HEAD
3ee2c76ae0 firewall: update to latest git HEAD
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
884be45 libubus: check for non-NULL data before running callbacks
Signed-off-by: John Crispin <john@phrozen.org>
(cherry picked from commit a5c3bbaf56)
This watchdog script tries to re-resolve hostnames for inactive WireGuard peers.
Use it for peers with a frequently changing dynamic IP.
persistent_keepalive must be set, recommended value is 25 seconds.
Run this script from cron every minute:
echo '* * * * * /usr/bin/wireguard_watchdog' >> /etc/crontabs/root
Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
[bump the package release]
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
(cherry picked from commit 20c4819c7b)
80b41cd version: bump snapshot
fe5f0f6 recieve: disable NAPI busy polling
e863f40 device: destroy workqueue before freeing queue
81a2e7e wg-quick: allow link local default gateway
95951af receive: use gro call instead of plain call
d9501f1 receive: account for zero or negative budget
e80799b tools: only error on wg show if all interfaces failk
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
[Added commit log to commit description]
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
(cherry picked from commit 57b808ec88)
* device: print daddr not saddr in missing peer error
* receive: style
Debug messages now make sense again.
* wg-quick: android: support excluding applications
Android now supports excluding certain apps (uids) from the tunnel.
* selftest: ratelimiter: improve chance of success via retry
* qemu: bump default kernel version
* qemu: decide debug kernel based on KERNEL_VERSION
Some improvements to our testing infrastructure.
* receive: use NAPI on the receive path
This is a big change that should both improve preemption latency (by not
disabling it unconditionally) and vastly improve rx performance on most
systems by using NAPI. The main purpose of this snapshot is to test out this
technique.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
(cherry picked from commit 4630159294)
This partly reverts ca32373c95 which lets
profiles that suppress packages to alter the package selection for all
devices of the target when building with CONFIG_TARGET_PER_DEVICE_ROOTFS.
In particular, this caused the brcm47xx Edimax PS-1208MFG profile to
disable mtd, dropbear, firewall and other essential packages for all
brcm47xx/generic builds.
To solve this problem, prevent profiles from mangling the global
DEFAULT_PACKAGES selection and restrict the supression of negated
packages to the local PACKAGE variable list only.
Fixes ca32373c95 ("target.mk: let profile remove from DEFAULT_PACKAGES")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit 69ea512c62)
The WDR4900v1 uses the P1040 SoC, so the device tree pulls in the
definition for the related P1010 SoC. However, the P1040 lacks the
CAAM/SEC4 hardware crypto accelerator which the P1010 device tree
defines. If left defined, this causes the CAAM drivers (if present) to
attempt to use the non-existent device, making various crypto-related
operations (e.g. macsec and ipsec) fail.
This commit overrides the incorrect dt node definition in the included
file.
See also:
- https://bugs.openwrt.org/index.php?do=details&task_id=1262
- https://community.nxp.com/thread/338432#comment-474107
Signed-off-by: Tim Small <tim@seoss.co.uk>
(cherry picked from commit e97aaf483c)
iproute2's tc was updated to support the recently upstreamed cake qdisc.
Backport this canonical support from upstream into iproute2 v4.16
There is no kernel kmod/userspace tc ABI change in this release from the
previous package bump, so everyone can breath a sigh of relief.
This is largely a code style change, the exception to prove the rule:
option 'autorate_ingress' has been changed to 'autorate-ingress' to fit
in with upstream option naming expectations.
No openwrt package (e.g. sqm-scripts) has knowledge of
'autorate_ingress' thus only users who made their own scripts or used
it within the 'dangerous configuration' options of sqm-scripts will be
affected.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
The original vendor's driver programmed the dma controller's
AHB HPROT values to enable bufferable, privileged mode. This
along with the "same priorty for both channels" fixes the
freezes according to @takimata, @And.short, that have been
reported on the forum by @ticerex.
Furtheremore, @takimata reported that the patch also improved
the performance of the HDDs considerably:
|<https://forum.lede-project.org/t/wd-mybook-live-duo-two-disks/16195/55>
|It seems your patch unleashed the full power of the SATA port.
|Where I was previously hitting a really hard limit at around
|82 MB/s for reading and 27 MB/s for writing, I am now getting this:
|
|root@OpenWrt:/mnt# time dd if=/dev/zero of=tempfile bs=1M count=1024
|1024+0 records in
|1024+0 records out
|real 0m 13.65s
|user 0m 0.01s
|sys 0m 11.89s
|
|root@OpenWrt:/mnt# time dd if=tempfile of=/dev/null bs=1M count=1024
|1024+0 records in
|1024+0 records out
|real 0m 8.41s
|user 0m 0.01s
|sys 0m 4.70s
|
|This means: 121 MB/s reading and 75 MB/s writing!
|
|[...]
|
|The drive is a WD Green WD10EARX taken from an older MBL Single.
|I repeated the test a few times with even larger files to rule out
|any caching, I'm still seeing the same great performance. OpenWrt is
|now completely on par with the original MBL firmware's performance.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Restarting service sysctl echos multiple errors like:
sysctl: -e: No such file or directory
After the first filename, all remaining arguments are treated
as files.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
procd needs processes to stay in foreground to remain under its gaze and
control. Failure to do so means service stop commands fail to actually
stop the process (procd doesn't think it's running 'cos the process has
exited already as part of its forking routing)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
(cherry picked from commit 9d5a246930)
Drop the parallel-unsafe custom Build/dtb macro and use the .dtb artifacts
produced by the generic image build code.
Also remove unused .dtb references in the mt7623 subtarget.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(backported from commit 8194f9ef4a)
First of all lengths should be compared after checking all blocks for
being good/bad. It's because requested length may differ from a final
one if there were some bad blocks.
Secondly it makes sense to also compare crc32 since we already have a
new one calculated.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 82498a7f7a)
Reading MTD data with (p)read doesn't return any error when accessing
bad block. As the result, with current code, CRC32 covers "data" stored
in bad blocks.
That behavior doesn't match CFE's one (bootloader simply skips bad
blocks) and may result in:
1) Invalid CRC32
2) CFE refusing to boot firmware with a following error:
Boot program checksum is invalid
Fix that problem by checking every block before reading its content.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 0f54489f75)
Bump to the latest cake recipe.
This backports tc class support to kernel 4.9 and other than conditional
kernel compilation pre-processor macros represents the cake that has
gone upstream into kernel 4.19. Loud cheer!
Fun may be had by changing cake tin classification for packets on
ingress. e.g.
tc filter add dev ifb4eth0 parent 800b: protocol ip u32 match \
ip dport 6981 0xffff action skbedit priority 800b:1
Where 800b: represents the filter handle for the ifb obtained by 'tc
qdisc' and the 1 from 800b:1 represents the cake tin number. So the
above example puts all incoming packets destined for port 6981 into the
BULK (lowest priority) tin.
f39ab9a Obey tin_order for tc filter classifiers
1e2473f Clean up after latest backport.
82531d0 Reorder includes to fix out of tree compilation
52cbc00 Code style cleanup
6cdb496 Fix argument order for NL_SET_ERR_MSG_ATTR()
cab17b6 Remove duplicate call to qdisc_watchdog_init()
71c7991 Merge branch 'backport-classful'
32aa7fb Fix compilation on Linux 4.9
9f8fe7a Fix compilation on Linux 4.14
ceab7a3 Rework filter classification
aad5436 Fixed version of class stats
be1c549 Add cake-specific class stats
483399d Use tin_order for class dumps
80dc129 Add class dumping
0c8e6c1 Fix dropping when using filters
c220493 Add the minimum class ops
5ed54d2 Start implementing tc filter/class support
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
(cherry picked from commit c729c43b39)
The previous callback code was fragile, dependent on some UCI callback
bugs and side-effects now fixed in master commit 73d8a6ab.
Update scripts to use callbacks where appropriate and necessary, while
using normal UCI config parsing for all else. This results in smaller,
simpler, more robust code. Use callbacks in generate.sh to only process
'interface' defaults and the varying entries for 'reclassify', 'default'
and 'classify' sections. Also switch qos-stat to use non-callback UCI
handling.
The current changes work independently of 73d8a6ab (i.e. both before and
after), and are consistent with UCI config parsing documentation.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
There are several long-standing issues present in the UCI shell API as
documented in https://wiki.openwrt.org/doc/devel/config-scripting. They
relate both to high-level, user-defined callback functions used to
process UCI config files, and also to low-level functions used within
scripts generally.
The related problems have been encountered now and in the past, e.g.
https://forum.openwrt.org/viewtopic.php?id=54295, and include:
a) UCI parsing option() function and user-defined option_cb() callbacks
being erroneously called during processing of "list" config file entries;
b) normal usage of the low-level config_set() unexpectedy calling any
defined option_cb() if present; and
c) handling of the list_cb() not respecting the NO_CALLBACK variable.
Root causes include a function stack "inversion", where the low-level
config_set() function incorrectly calls the high-level option() function,
intended only for processing the "option" keyword of UCI config files.
This change addresses the inversion and other issues, making the option
handling code more consistent and smaller, and simplifying developers'
usage of UCI callbacks.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
Starting with 4.14, the "amcc,dwc-otg" needs to be used
in order to get the usb-otg to work.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 12b80f1cab)
Fix broken DHCPv6 servers which provide the server unicast option but
do not reply on DHCPv6 renew messages directed to the IPv6 address
contained in the server unicast option which results in broken IPv6
connectivity.
67ae6a7 odhcp6c: add option to ignore Server Unicast option
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This commit adds the get_status_led method to diag.sh, which sets the
boot-led as status-led for scripts using this method to get a
status-led.
This method is used platform-independent in downstream project gluon to
set the LED used to indicate the config-mode.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 4fc005197a)
On Debian, busybox does have a time applet, but it does not support the -f
flag. Catch this in prereq check to give users to proper error message.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit b123921a92)
An incorrect variable name was referenced in KERNEL_FILE_DEPENDS, leading
to the omission of the backport-* patch dirs in the generation of the
prepared stamp name.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit 36fa1bbf6f)
Backport hot off the press upstream netlink patch. Fixes stats display
from CAKE qdisc on MIPS allowing us to bump CAKE to latest version.
The gen_stats facility will add a header for the toplevel nlattr of type
TCA_STATS2 that contains all stats added by qdisc callbacks. A reference
to this header is stored in the gnet_dump struct, and when all the
per-qdisc callbacks have finished adding their stats, the length of the
containing header will be adjusted to the right value.
However, on architectures that need padding (i.e., that don't set
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS), the padding nlattr is added
before the stats, which means that the stored pointer will point to the
padding, and so when the header is fixed up, the result is just a very
big padding nlattr. Because most qdiscs also supply the legacy TCA_STATS
struct, this problem has been mostly invisible, but we exposed it with
the netlink attribute-based statistics in CAKE.
Fix the issue by fixing up the stored pointer if it points to a padding
nlattr.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
(cherry picked from commit 3698b34a00)
- remove misaligned custom buffer allocation in the NAND driver
- remove broken bounce buffer implementation for 16-byte align
Let the MTD core take care of both
Fixes messages like these:
[ 102.820541] Data buffer not 16 bytes aligned: 87daf08c
Signed-off-by: Felix Fietkau <nbd@nbd.name>
08719b1 mt76: use a per rx queue page fragment cache
4d2c565 mt76x2: reset HW before probe
f622975 mt76x2: fix CCK protection control frame rate
6780375 mt76x2: add frame protection support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Using the NAPI or netdev frag cache along with other drivers can lead to
32 KiB pages being held for a long time, despite only being used for
very few page fragment.
This can happen if the ethernet driver grabs one or two fragments for rx
ring refill, while other drivers use (and free up) the remaining
fragments. The 32 KiB higher-order page can only be freed once all users
have freed their fragments, which only happens after the rings of all
drivers holding the fragments have wrapped around.
Depending on the traffic patterns, this can waste a lot of memory and
look a lot like a memory leak
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Allow enabling/commenting/disabling each feed individually by using a
tristate config symbol.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit 16035a7dd3)
FEEDS_ENABLED and FEEDS_DISABLED are derived from FEEDS_AVAILABLE, not
FEEDS_INSTALLED.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit 6dac434c00)
Setting CONFIG_FEED_... symbols combined two different effects: Disabling
a feed in the generated opkg distfeeds.conf, and omitting the feed from
PACKAGE_SUBDIRS.
It does not make sense to omit built feeds from PACKAGE_SUBDIRS, as it will
only lead to packages that can be enabled in .config (and that will
consequently be built) not to be found during rootfs creation, breaking
the build. All feeds that packages are emitted to should simply always be
added to PACKAGE_SUBDIRS instead; the CONFIG_FEED_... only configure the
generated distfeeds.conf like this.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit 9af22f1ac9)
The src-dummy method does not actually obtain any feed, but it can be used
to insert addtional entries into the opkg distfeeds.conf. This is useful to
make package feeds available to users without requiring the corresponding
source feeds to be available during build.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit 6bdd5d8459)
The line that produces factory image was accidentally left by me while
testing before inital commit.
I came to the conclusion that flashing from OEM firmware does not work
(seems to share this behavior with other tplinks based on mt7628).
I have not done any further analysis, as I was unable to open the
case and attach a serial port (too much glue). Maybe i will try once
more.
So the way to do initial flashing (or un-bricking) is to use the
tftp-recover image. It is possible to revert to OEM firmware with tftp
recovery; in this case the first 512 bytes the image file need to be
cut off.
Signed-off-by: Peter Lundkvist <peter.lundkvist@gmail.com>
[add explaination provided via mail as commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Refreshed all patches
Reworked patches to match upstream:
335-v4.16-netfilter-nf_tables-add-single-table-list-for-all-fa.patch
Compile-tested on: cns3xxx, imx6, x86_64
Runtime-tested on: cns3xxx, imx6, x86_64
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Enables support for Dynack feature.
When a remote station is far away, we need to compensate for the distance
by allowing more time for an ACK to arrive back before issueing a retransmission.
Currently, it needs to be set fixed to indicate the maximum distance the remote
station will ever be.
While this mostly works for static antennae, it introduces 2 issues:
- If the actual distance is less, speed is reduced due to a lot of wates wait-time
- If the distance becomes greater, retries start to occur and comms can get lost.
Allowing to set it dynamically using dynack ensures the best possible tradeoff
between speed vs distance.
This feature is currently only supported in ath9k.
it is also disabled by default.
Enabling it can be done in 2 ways:
- issue cmd: iw phy0 set distance auto
- sending the NL80211_ATTR_WIPHY_DYN_ACK flag to mac80211 driver using netlink
Disabling it can be done by providing a valid fixed value.
To give an idea of a practical example:
In my usecase, we have mesh wifi device installed on ships/platforms.
Currently, the coverage class is set at 12000m fixed.
When a vessel moved closer (ex. 1500m), the measured link capacity was a lot
lower compared to setting the coverage class fixed to 1500m
Dynack completely solved this, nearly providing double the bandwidth at closer range
compared to the fixed setting of 12000m being used.
Also when a vessel sailed to a distance greater than the fixed setting,
communication was lost as the ACK's never arrived within the max allowed timeframe.
Actual distance: 6010m
iperf 60s run avg
Fixed 12150m: 31 Mbit/s
Dynack: 58 Mbit/s
Fixed 6300m: 51 Mbit/s
Dynack: 59 Mbit/s
Fixed 3000m: 13 Mbit/s (lots of retries)
Dynack: 58 Mbit/s
Actual distance: 1504m
iperf 60s run avg
Fixed 12150m: 31 Mbit/s
Dynack: 86 Mbit/s
Fixed 6300m: 55 Mbit/s
Dynack: 87 Mbit/s
Fixed 3000m: 67 Mbit/s
Dynack: 87 Mbit/s
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Partition name is picked by a parser_trx_data_part_name(). It has to
get correct partition offset (taking care of bad blocks) to work
properly.
This fixes UBI support for devices that have kernel flashed on partition
with a bad block.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 7ddba08d87)
Most of the implementations behind cfg80211_get_station will not initialize
sinfo to zero before manipulating it. For example, the member "filled",
which indicates the filled in parts of this struct, is often only modified
by enabling certain bits in the bitfield while keeping the remaining bits
in their original state. A caller without a preinitialized sinfo.filled can
then no longer decide which parts of sinfo were filled in by
cfg80211_get_station (or actually the underlying implementations).
cfg80211_get_station must therefore take care that sinfo is initialized to
zero. Otherwise, the caller may tries to read information which was not
filled in and which must therefore also be considered uninitialized. In
batadv_v_elp_get_throughput's case, an invalid "random" expected throughput
may be stored for this neighbor and thus the B.A.T.M.A.N V algorithm may
switch to non-optimal neighbors for certain destinations.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
(cherry picked from commit 87493dac11)
Board Data File (BDF) is loaded upon driver boot-up procedure. The right
board data file is identified on QCA4019 using bus, bmi-chip-id and
bmi-board-id.
The problem, however, can occur when the (default) board data file cannot
fulfill the vendor requirements and it is necessary to use a different
board data file.
This problem was solved for SMBIOS by adding a special SMBIOS type 0xF8.
Something similar has to be provided for systems without SMBIOS but with
device trees. No solution was specified by QCA and therefore a new one has
to be found for ath10k.
The device tree requires addition strings to define the variant name
wifi@a000000 {
status = "okay";
qcom,ath10k-calibration-variant = "RT-AC58U";
};
wifi@a800000 {
status = "okay";
qcom,ath10k-calibration-variant = "RT-AC58U";
};
This would create the boarddata identifiers for the board-2.bin search
* bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=RT-AC58U
* bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=RT-AC58U
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
(cherry picked from commit 1c01e02575)
dfd9827 version: bump snapshot
88729f0 wg-quick: android: prevent outgoing handshake packets from being dropped
1bb9daf compat: more robust ktime backport
68441fb global: use fast boottime instead of normal boottime
d0bd6dc global: use ktime boottime instead of jiffies
18822b8 tools: fix misspelling of strchrnul in comment
0f8718b manpages: eliminate whitespace at the end of the line
590c410 global: fix a few typos
bb76804 simd: add missing header
7e88174 poly1305: give linker the correct constant data section size
fd8dfd3 main: test poly1305 before chacha20poly1305
c754c59 receive: don't toggle bh
Compile-tested-for: ath79 Archer C7 v2
Run-tested-on: ath79 Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
(cherry picked from commit 3ce11588f6)
Fixes a potential infinite loop bug when in unlimited (ie not using
built in shaper) mode.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
(cherry picked from commit 4bd4ece9ea)
This bumps to the latest & possibly greatest cake, sadly it's still
inedible but from an SQM point of view quite tasty :-)
Main tweaks since previous bump, improved ack_filter, some extra stats,
support for 64bit netlink parameters (higher rates/byte counters)
0520a6c Fix NAT option handling
8da93e1 Make sure we always call qdisc_watchdog_init() in cake_init()
f65daf6 Fix mismatched parenthesis
51d4ab3 Change flag handling to be safe even when mixing with non-eligible ACKs
f2ea091 ack_filter: protect DCTCP with stricter filtering of ECE marks
28b4560 ACK filter: Handle wrapping sequence numbers and DSACKs
73f62d9 Use the right PAD attribute for options
5969c14 Use 32 for tin backlog
e289f31 Move all the u64 netlink attributes together
36180a0 Check ACK seqno before parsing SACKs
91bbc01 Merge branch 'mine' into cobalt
58c55ec Rework SACK check to compare the ranges of two SACKs
9a5d593 ack_filter: Add proper handling of SACKs
eca95d4 ack_filter: short-circuit TCP flag check
d50a246 compat: backport some ktime functions
7b7ad11 compat: define tcpopt_fastopen for pre-4.1 kernels
ca54cdb Fix ktime compare
9d7dcc0 ack filter: Parse TCP options and only drop safe ones
b119882 Return EOPNOTSUPP on NAT option if conntrack is not available
842d7f0 Don't try to pad stats with tin_stats padding
bd46dc2 Use 64-bit divide helper
8e41bf0 Make sure we never drop SACKs when filtering ACKs
66e5d60 Avoid comparing ktime_t to scalar values
7fab017 Actually commit the ktime_t changes
fca6d13 Switch to ktime_t and get rid of cobalt.h
6f7e5af Can't use do_div with 64-bit divisors
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
(cherry picked from commit abeae38dbb)
Bump iproute2/tc support of cake.
Add support for cake's change to u64 attribute passing for certain
attributes (rate & byte counts)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
(cherry picked from commit a2165f936e)
Netgear R7800 switch LAN ports are numbered backwards in LuCI,
i.e. numbering is not corresponding to the actual physical port labels,
patch fixes that.
Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com>
[merged with existing board using the same config]
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
To keep the status of a LED connected to the stp during boot, the get
callback is required. If the callback is missing and the LED default
state is set to keep in the devicetree, the gpio led driver errors out
during load.
Fixes: FS#1620
Signed-off-by: Mathias Kresin <dev@kresin.me>
Move SCAN_DEPS to scan.mk to eliminate redundancy with scripts/feeds
Add image/*.mk to SCAN_DEPS for targets to pick up newly added devices
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In some cases, recent builds fail to boot from flash with at least some
MT7621 based devices. The error message is:
"LZMA ERROR 1 - must RESET board to recover"
Booting the same kernel via TFTP works for some reason.
Through testing I figured out that limiting the LZMA dictionary size
seems to prevent these errors
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move to i2c pins pinmux node to the pinctrl node.
Fixes: a0685deec4 ("ramips: Add i2c support for mt7620n")
Signed-off-by: Andrey Jr. Melnikov <temnota.am@gmail.com>
[fix commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Remove the "firmware" partition definition from the DTS of R7800
to fix sysupgrade.
Commit 4645a6d3 defined CONFIG_MTD_SPLIT_UIMAGE_FW=y for ipq806x
and that causes mtd to misbehave as additional kernel and ubi
partitions are detected from inside the "firmware" partition.
[ 1.111324] 0x000001480000-0x000001880000 : "kernel"
[ 1.121005] 0x000001880000-0x000007900000 : "ubi"
[ 1.283912] 0x000007900000-0x000008000000 : "reserve"
[ 1.296407] 0x000001480000-0x000007900000 : "firmware"
[ 1.468043] no rootfs found after FIT image in "firmware"
[ 2.426860] 2 uimage-fw partitions found on MTD device firmware
[ 2.426931] 0x000001480000-0x000001880000 : "kernel"
[ 2.440420] 0x000001880000-0x000007900000 : "ubi"
Both kernel and ubi are already defined in DTS, so this duplication
leads into errors in sysupgrade:
Writing from <stdin> to kernel ...
ubiattach: error!: strtoul: unable to parse the number '6 mtd10'
ubiattach: error!: bad MTD device number: "6 mtd10"
The partition is defined to same area as kernel+ubi, and is not
needed for sysupgrade anymore. Remove it to fix things.
Only tested for the R7800 but all of them should behave equal.
Fixes: FS#1617
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
[squashed commits, add "tested on" note]
Signed-off-by: Mathias Kresin <dev@kresin.me>
Increase the available flash memory size in Netgear R7800
by taking into the use the unused "netgear" partition
that is located after the firmware partition.
Available flash space for kernel+rootfs+overlay increases
by 68 MB from 32 MB to 100 MB.
In a typical build, overlay space increases from 15 to 85,
increasing the package installation possibilities greatly.
Reverting to the OEM firmware is still possible, as the OEM
firmware contains logic to initialise the "netgear" partition
if its contents do not match expectations. In OEM firmware,
"netgear" contains 6 UBI sub-partitions that are defined in
/etc/netgear.cfg and initialisation is done by /etc/preinit
Tested with Openwrt master r7093-4fdc6ca31b and OEM V1.0.2.52
Reference to forum discussion in Netgear R7800 exploration thread:
https://forum.lede-project.org/t/netgear-r7800-exploration-ipq8065-qca9984/285/1118
(messages 1118-1158)
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
WN-GX300GR has 5x RJ45 ports (port 0-4), and these ports are
orderd on the device as follows:
4 3 2 1 0
1-4: lan
0: wan
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
With current uboot default configuration the bootloader will
fail to start the OpenWrt firmware with the following error:
-----
unexpected character 'b' at the end of partition
Error initializing mtdparts!
incorrect device type in ubi
Partition ubi not found!
Error, no UBI device/partition selected!
Wrong Image Format for bootm command
Error occured, error code = 112
-----
If the uboot configuration is examined with printenv
I can see that mdtparts line (on a nsa310) is wrong:
-----
mtdparts=mtdparts=orion_nand:0x0c0000(uboot),
0x80000(uboot_env),0x7ec0000(ubi)bootargs_root=
----
The "bootargs_root=" that was appended to it should not be there.
Fix the issue by adding a \0 line terminator at the end of affected lines,
mimicking what is also done by uboot upstream.
This issue was detected and confirmed on a nsa310, nsa325 and
a pogoplug v4, but it's not hardware-specific, so apply the same fix
to other devices as well.
Note that the issue is with the uboot's integrated boot configuration,
which is not used unless the uboot configuration in flash is unavailable
(erased or corrupted), which happens only on first time installation,
or if the user deletes the uboot configuration when upgrading uboot.
People just upgrading from an older uboot without erasing their previous
uboot configuration stored in flash would not have noticed this issue.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
After a very enlightening but unfortunately far too short exchange with Jes
we mutually agreed to drop the patches. They are unfortunately not ready
yet.
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: John Crispin <john@phrozen.org>
(cherry picked from commit 66c5696cdf)
Differing from all other archs supported by musl, MIPS defines SO_PEERSEC
to 30 instead of 31.
Patch has also been submitted upstream.
Reported-by: Andrey Jr. Mlenikov <temnota.am@gmail.com>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit 4b50854a60)
This PR adds support for a popular low-cost 2.4GHz N based AP
Specifications:
- SoC: Qualcomm Atheros QCA9533 (650MHz)
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 2.4GHz N based built into SoC 2x2
- Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Notes:
TP-Link does not use bootstrap registers so without this patch reference
clock detects as 40MHz while it is actually 25MHz.
This is due to messed up bootstrap resistor configuration on the PCB.
Provided GPL code just forces 25MHz reference clock.
That causes booting with completely wrong clocks, for example, CPU tries
to boot at 1040MHz while the stock is 650MHz.
So this PR depends on PR #672 to remove 40MHz reference clock.
Thanks to Sven Eckelmann <sven@narfation.org> for properly patching that.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 5c5bf8b865)
Add support for detecting TP-Link Pharos v2 boards.
They use different format in product-info partition than v1 boards.
Code was written mostly by Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 2524febf79)
It was described by Arend as:
> This series is intended for 4.17 and includes following:
>
> * rework bus layer attach code.
> * remove duplicate variable declaration.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 0da9303e5b)
This fixes missing rootfs on above device:
[ 2.652292] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
(...)
[ 2.687909] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
Fixes: 05cb6aa69f ("bcm53xx: replace linux,part-probe with a proper partitions subnode")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit e53d0da775)
This reverts commit 97b1765a45.
The tree is in an inconsistent state and we need to complete some rebranding.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This reverts commit 55df39e684.
The tree is in an inconsistent state and we need to complete some rebranding.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
this makes sure that offloading support is properly included for v4.14 targets.
Signed-off-by: John Crispin <john@phrozen.org>
(cherry picked from commit ebe1216c7c)
When the 160mhz width is selected the ath10k firmware crash. This fix this problem.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
(cherry picked from commit 134e832814)
Includes specific support for PH8(1e2d-0053) / ELS61(1e2d-005b) modules.
Note for ELS61, the serial driver changes from serial option(ttyUSB) to usb-cdc (ttyACM).
Two additional fixes in this commit resolve issues with ttyACM devices: -
* wwan.sh - sys-fs has a subdirectory indirection (*/tty/ttyACMx) which was not handled properly
* wwan.usb - dependent scripts were not included, so this never actually called proto_set_available for example (and relied on inadvertent call for ttyUSB case)
Signed-off-by: David Thornley <david.thornley@touchstargroup.com>
(cherry picked from commit cb262b0939)
Replace 204-udhcpc_no_msg_dontroute patch by the upstream busybox fix
which removes the code which requires the server ID to be on local
network
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Both version of the vg3503j have the LAN1 labelled port connected to
switch port 4 and the LAN2 labelled port connected to switch port 2.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Specification:
- SoC: MediaTek MT7620A
- Flash: 8 MB
- RAM: 64 MB
- Ethernet: 4 FE ports and 1 GE port (RTL8211F on port 5)
- Wireless radio: MT7620 for 2.4G and MT7612E for 5G, both equipped with external PA.
- UART: 1 x UART on PCB - 57600 8N1
Flash instruction:
The U-boot is based on Ralink SDK so we can flash the firmware using UART:
1. Configure PC with a static IP address and setup an TFTP server.
2. Put the firmware into the tftp directory.
3. Connect the UART line as described on the PCB.
4. Power up the device and press 2, follow the instruction to
set device and tftp server IP address and input the firmware
file name. U-boot will then load the firmware and write it into
the flash.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
072fdac mt76x2: mac: consider multicast/broadcast frames in ewma rssi estimation
f450659 mt76x2: improve gain adjustment in noisy environments
1d4ca10 mt76x2: track rssi for gain adjustment per station
Signed-off-by: Felix Fietkau <nbd@nbd.name>
TP-Link Archer C7 v5 is a dual-band AC1750 router, based on Qualcomm/Atheros
QCA9563+QCA9880.
Specification:
- 750/400/250 MHz (CPU/DDR/AHB
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 10x LED, 2x button
- UART header on PCB
Flash instruction:
1. Upload lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin via Web interface
Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin
and rename it to ArcherC7v5_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
Signed-off-by: Arvid E. Picciani <aep@exys.org>
(cherry picked from commit bf39d5594b)
This commit adds support for the AVM Fritz!WLAN Repeater 450E
SOC: Qualcomm QCA9556 (Scorpion) 560MHz MIPS74Kc
RAM: 64MB Zentel A3R12E40CBF DDR2
FLASH: 16MiB Winbond W25Q128 SPI NOR
WLAN1: QCA9556 2.4 GHz 802.11b/g/n 3x3
INPUT: WPS button
LED: Power, WiFi, LAN, RSSI indicator
Serial: Header Next to Black metal shield
Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4GHz WiFi (correct MAC)
- Installation via EVA bootloader
- OpenWRT sysupgrade
- Buttons
- Most LEDs
Not working:
- 2 RSSI LEDs
AVM used for RSSI{0,1} two of the Ethernet PHYs LEDs which they
control over MDIO. Our driver doesn't expose these LEDs as GPIOs.
While it is possible to implement this feature, it would require an
additional kernel patch for a minor functionality.
Installation via EVA:
In the first seconds after Power is connected, the bootloader will
listen for FTP connections on 192.168.178.1. Firmware can be uploaded
like following:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1
Note that this procedure might take up to two minutes.
You need to powercycle the Device afterwards to boot OpenWRT.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit b4bf43c667)
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 128 MB Nanya NT5CC64M16GP-DI
FLASH: 16 MiB Macronix MX25L12845EMI-12G
ETH: Qualcomm QCA8072
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT: WPS, Mode-toggle-switch
LED: Power, WLAN 2.4GHz, WLAN 5GHz, LAN, WPS
(LAN not controllable by software)
(WLAN each green / red)
SERIAL: Header next to eth-phy.
VCC, TX, GND, RX (Square hole is VCC)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet (Correct MAC-address)
- 2.4 GHz WiFi (Correct MAC-address)
- 5 GHz WiFi (Correct MAC-address)
- Factory installation from tftp
- OpenWRT sysupgrade
- LEDs
- WPS Button
Not Working:
- Mode-toggle-switch
Install via TFTP:
Connect to the devices serial. Hit Enter-Key in bootloader to stop
autobooting. Command `tftpboot` will pull an initramfs image named
`C0A86302.img` from a tftp server at `192.168.99.08/24`.
After successfull transfer, boot the image with `bootm`.
To persistently write the firmware, flash an openwrt sysupgrade image
from inside the initramfs, for example transfer
via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device
with `sysupgrade -n /tmp/<sysupgrade>`.
append-cmdline patch taken from chunkeeys work on the NBG6617.
Signed-off-by: Magnus Frühling <skorpy@frankfurt.ccc.de>
Co-authored-by: David Bauer <mail@david-bauer.net>
Co-authored-by: Christian Lamparter <chunkeey@googlemail.com>
(cherry picked from commit 4b280ad91a)
This commit adds support for the OCEDO Koala
SOC: Qualcomm QCA9558 (Scorpion)
RAM: 128MB
FLASH: 16MiB
WLAN1: QCA9558 2.4 GHz 802.11bgn 3x3
WLAN2: QCA9880 5 GHz 802.11nac 3x3
INPUT: RESET button
LED: Power, LAN, WiFi 2.4, WiFi 5, SYS
Serial: Header Next to Black metal shield
Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi
- 5 GHz WiFi
- TFTP boot from ramdisk image
- Installation via ramdisk image
- OpenWRT sysupgrade
- Buttons
- LEDs
Installation seems to be possible only through booting an OpenWRT
ramdisk image.
Hold down the reset button while powering on the device. It will load a
ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8.
Note: depending on the present software, the device might also try to
pull a file called 'koala-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.
Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.
Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with
> fw_setenv bootcmd run bootcmd_1
Afterwards you can reboot the device.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit e36f8b3f39)
The QCA9556 only has a SGMII interface. However the speed on the
ethernet link is set for the non-existant xMII interface.
This commit fixes this behavior.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit abb4ab076f)
This commit adds support for the Mikrotik RouterBOARD RBM33g.
=Hardware=
The RBM33g is a mt7621 based device featuring three gigabit ports, 2
miniPCIe slots with sim card sockets, 1 M.2 slot, 1 USB 3.0 port and a male
onboard RS-232 serial port. Additionally there are a lot of accessible
GPIO ports and additional buses like i2c, mdio, spi and uart.
==Switch==
The three Ethernet ports are all connected to the internal switch of the
mt7621 SoC:
port 0: Ethernet Port next to barrel jack with PoE printed on it
port 1: Innermost Ethernet Port on opposite side of RS-232 port
port 2: Outermost Ethernet Port on opposite side of RS-232 port
port 6: CPU
==Flash==
The device has two spi flash chips. The first flash chips is rather small
(512 kB), connected to CS0 by default and contains only the RouterBOOT
bootloader and some factory information (e.g. mac address).
The second chip has a size of 16 MB, is by default connected to CS1 and
contains the firmware image.
==PCIe==
The board features three PCIe-enabled slots. Two of them are miniPCIe
slots (PCIe0, PCIe1) and one is a M.2 (Key M) slot (PCIe2).
Each of the miniPCIe slots is connected to a dedicated mini SIM socket
on the back of the board.
Power to all three PCIe-enabled slots is controlled via GPIOs on the
mt7621 SoC:
PCIe0: GPIO9
PCIe1: GPIO10
PCIe2: GPIO11
==USB==
The board has one external USB 3.0 port at the rear. Additionally PCIe
port 0 has a permanently enabled USB interface. PCIe slot 1 shares its
USB interface with the rear USB port. Thus only either the rear USB port
or the USB interface of PCIe slot 1 can be active at the same time. The
jumper next to the rear USB port controls which one is active:
open: USB on PCIe 1 is active
closed: USB on rear USB port is active
==Power==
The board can accept both, passive PoE and external power via a 2.1 mm
barrel jack. The input voltage range is 11-32 V.
=Installation=
==Prerequisites==
A USB -> RS-232 Adapter and a null modem cable are required for
installation.
To install an OpenWRT image to the device two components must be built:
1. A openwrt initramfs image
2. A openwrt sysupgrade image
===initramfs & sysupgrade image===
Select target devices "Mikrotik RBM33G" in
openwrt menuconfig and build the images. This will create the images
"openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" and
"openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" in the output
directory.
==Installing==
**Make sure to back up your RouterOS license in case you do ever want to
go back to RouterOS using "/system license output" and back up the created
license file.**
Serial settings: 115200 8N1
The installation is a two-step process. First the
"openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" must be booted
via tftp:
1. Set up a dhcp server that points the bootfile to tftp server serving
the "openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin"
initramfs image
2. Connect to WAN port (left side, next to sys-LED and power indicator)
3. Connect to serial port of board
4. Power on board and enter RouterBOOT setup menu
5. Set boot device to "boot over ethernet"
6. Set boot protocol to "dhcp protocol" (can be omitted if DHCP server
allows dynamic bootp)
6. Save config
7. Wait for board to boot via Ethernet
On the serial port you should now be presented with the OpenWRT boot log.
The next steps will install OpenWRT persistently.
1. Copy "openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" to the device
using scp.
2. Write openwrt to flash using "sysupgrade
openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin"
Once the flashing completes reboot the router and let it boot from flash.
It should boot straight to OpenWRT.
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
0bc4230 version: bump snapshot
ed04799 poly1305: add missing string.h header
cbd4e34 compat: use stabler lkml links
caa718c ratelimiter: do not allow concurrent init and uninit
894ddae ratelimiter: mitigate reference underflow
0a8a62c receive: drop handshake packets if rng is not initialized
cad9e52 noise: wait for crng before taking locks
83c0690 netlink: maintain static_identity lock over entire private key update
0913f1c noise: take locks for ss precomputation
073f31a qemu: bump default kernel
bec4c48 wg-quick: android: don't forget to free compiled regexes
7ce2ef3 wg-quick: android: disable roaming to v6 networks when v4 is specified
9132be4 dns-hatchet: apply resolv.conf's selinux context to new resolv.conf
41a5747 simd: no need to restore fpu state when no preemption
6d7f0b0 simd: encapsulate fpu amortization into nice functions
f8b57d5 queueing: re-enable preemption periodically to lower latency
b7b193f queueing: remove useless spinlocks on sc
5bb62fe tools: getentropy requires 10.12
4e9f120 chacha20poly1305: use slow crypto on -rt kernels on arm too
Compiled-for: ar71xx, lantiq
Run-tested-on: ar71xx Archer C7 v2 & lantiq HH5a
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Commit ecd954d530 installs specific interface triggers which rewrites the dnsmasq config
file and restarts dnsmasq if the network interface becomes active for which a trigger
has been installed.
In case no dhcp sections are specified or ignore is set to 1 dnsmasq will not be started
at startup which breaks DNS resolving.
Fix this by ditching the BOOT check in start_service and always start dnsmasq at startup.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
ELECOM WRC-1167GHBK2-S is a 2.4/5 GHz band 11ac router, based on
MediaTek MT7621A.
Specification:
- MT7621A (2-Cores, 4-Threads)
- 128 MB of RAM (DDR3)
- 16 MB of Flash (SPI)
- 2T2R 2.4/5 GHz
- MediaTek MT7615D
- 5x 10/100/1000 Mbps Ethernet
- 6x LEDs, 2x keys
- UART header on PCB
- Vcc, GND, TX, RX from ethernet port side
- baudrate: 57600 bps
Flash instruction using factory image:
1. Rename the factory image to "wrc-1167ghbk2-s_v0.00.bin"
2. Connect the computer to the LAN port of WRC-1167GHBK2-S
3. Connect power cable to WRC-1167GHBK2-S and turn on it
4. Access to "http://192.168.2.1/details.html" and open firmware
update page ("手動更新（アップデート）")
5. Select the factory image and click apply ("適用") button
6. Wait ~150 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
I-O DATA WN-GX300GR is a 2.4 GHz band 11n router, based on MediaTek
MT7621S.
Specification:
- MT7621S (1-Core, 2-Threads)
- 64 MB of RAM
- 8 MB of Flash (SPI)
- 2T2R 2.4 GHz
- 5x 10/100/1000 Mbps Ethernet
- 2x LEDs, 4x keys (2x buttons, 1x slide switch)
- UART header on PCB
- Vcc, GND, TX, RX from ethernet port side
- baudrate: 115200 bps (U-Boot, OpenWrt)
Flash instruction using initramfs image:
1. Connect serial cable to UART header
2. Rename OpenWrt initramfs image for WN-GX300GR to "uImageWN-GX300GR"
and place it in the TFTP directory
3. Set the IP address of the computer to 192.168.99.8, connect to the
LAN port of WN-GX300GR, and start the TFTP server on the computer
4. Connect power cable to WN-GX300GR and turn on the router
5. Press "1" key on the serial console to interrupt boot process on
U-Boot, press Enter key 3 times and start firmware download via TFTP
6. WN-GX300GR downloads initramfs image and boot with it
7. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with sysupgrade image for WN-GX300GR
8. Wait ~150 seconds to complete flasing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
NEC Aterm WG2600HP is a 2.4/5 GHz band 11ac router, based on Qualcomm
IPQ8064.
Specification:
- IPQ8064 (384 - 1,400 MHz)
- 512 MB of RAM
- 32 MB of Flash (SPI)
- 4T4R 2.4/5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 12x LEDs, 4x keys
- 1x USB 3.0 Type-A
- UART header on PCB
- RX, TX, NC, GND, Vcc from power connector side
- baudrate: 115200 bps
Flash instruction using initramfs image:
1. Connect serial cable to UART header
2. Connect power cable and turn on the router
3. When the "Press the [f] key and hit [enter] to enter failsafe mode"
message is displayed on the console, press the "f" key and Enter key
sequentially to enter the failsafe mode
4. create fw_env.config file with following contents on failsafe mode:
/dev/mtd9 0x0 0x10000 0x10000
5. Execute following commands to add and change the environment
variables of U-Boot
fw_setenv ipaddr "192.168.0.1"
fw_setenv serverip "192.168.0.2"
fw_setenv autostart "yes"
fw_setenv bootcmd "tftpboot 0x44000000 wg2600hp-initramfs.bin;
bootipq"
6. Set the IP address of the computer to 192.168.0.2, connect to the LAN
port of WG2600HP, and start the TFTP server on the computer
7. Rename OpenWrt initramfs image for WG2600HP to
"wg2600hp-initramfs.bin" and place it in the TFTP directory
8. Remove power cable from WG2600HP, reconnect it and restart WG2600HP
9. WG2600HP downloads initramfs image from TFTP server on the computer,
loads it and boot with initramfs image
10. On the initramfs image, execute "mtd erase firmware" to erase stock
firmware and execute sysupgrade with the sysupgrade image
11. Wait ~180 seconds to complete flashing
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Add wpad-mini if wireless drivers are included. Drop the mt76 package if
both of the provided drivers are included with their own packages.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Be compatible with ISPs which don't support the destination option header containing
the tunnel encapsulation limit as reported in FS#1501.
Setting the uci parameter encaplimit to ignore; allows to disable the insertion
of the destination option header in the ds-lite packets.
Otherwise the tunnel encapsulation limit value can be set to a value from 0 till 255
by setting the encaplimit uci parameter accordingly.
If no encaplimit value is specified the default value is 4 as before.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Be compatible with ISPs which don't support the destination option header containing
the tunnel encapsulation limit as reported in FS#1501 for dynamic created ds-lite/map
interfaces.
Setting the uci parameter encaplimit_dslite/map to ignore; allows to disable the insertion
of the destination option header for the dynamic created ds-lite/map interface.
Otherwise the tunnel encapsulation limit value can be set to a value from 0 till 255
by setting the encaplimit_dslite/map uci parameter accordingly.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Be compatible with ISPs which don't support the destination option header containing
the tunnel encapsulation limit as reported in FS#1501.
Setting the uci parameter encaplimit to ignore; allows to disable the insertion
of the destination option header in the map-e packets.
Otherwise the tunnel encapsulation limit value can be set to a value from 0 till 255
by setting the encaplimit uci parameter accordingly.
If no encaplimit value is specified the default value is 4 as before.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Since the beginning there's been an issue with initializing the Atheros
based MiniPCIe wireless cards. Here's an example of kerenel log:
OF: PCI: host bridge /soc/pcie@d0070000 ranges:
OF: PCI: MEM 0xe8000000..0xe8ffffff -> 0xe8000000
OF: PCI: IO 0xe9000000..0xe900ffff -> 0xe9000000
advk-pcie d0070000.pcie: link up
advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [bus 00-ff]
pci_bus 0000:00: root bus resource [mem0xe8000000-0xe8ffffff]
pci_bus 0000:00: root bus resource [io 0x0000-0xffff](bus address[0xe9000000-0xe900ffff])
pci 0000:00:00.0: BAR 0: assigned [mem0xe8000000-0xe801ffff 64bit]
pci 0000:00:00.0: BAR 6: assigned [mem0xe8020000-0xe802ffff pref]
[...]
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x3c
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x44
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4
ath9k 0000:00:00.0: enabling device (0000 -> 0002)
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x3c
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0xc
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x40
ath9k 0000:00:00.0: request_irq failed
advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4
ath9k: probe of 0000:00:00.0 failed with error -22
The same happens for ath5k cards, while ath10k card didn't appear at
all (not detected):
OF: PCI: host bridge /soc/pcie@d0070000 ranges:
OF: PCI: MEM 0xe8000000..0xe8ffffff -> 0xe8000000
OF: PCI: IO 0xe9000000..0xe900ffff -> 0xe9000000
advk-pcie d0070000.pcie: link never came up
advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [bus 00-ff]
pci_bus 0000:00: root bus resource [mem0xe8000000-0xe8ffffff]
pci_bus 0000:00: root bus resource [io 0x0000-0xffff](bus address[0xe9000000-0xe900ffff])
advk-pcie d0070000.pcie: config read/write timed out
Following the issue on esppressobin.net forum [1] the workaround seems
to be limiting the speed of PCIe bridge to 1st generation. This fixed
the initialisation of all tested Atheros wireless cards.
The change shouldn't affect the performance for wireless cards,
it could reduce the performance of storage controller cards but since
OpenWrt focuses on wireless connectivity, fixing compatibility with
wireless cards should be a priority.
For the record, the iwlwifi and mt76 cards were not affected by this
issue.
1. http://espressobin.net/forums/topic/which-pcie-wlan-cards-are-supported
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
(cherry picked from commit 772258044b)
Busybox time supports the GNU time '-f' syntax used by the build time
logging implemented in ff6e62b288, however the prerequisite check added
only works with GNU time installed as `time` or `gtime`.
As busybox is a multicall binary, the name of the symlink setup by
SetupHostCommand also must be changed from `gtime` to `time` to fix the
value of argv[0]. This causes a number of shells (including bash) to use
their builtin impelementation of time, so the sole invocation has been
changed to use `env time` to use the value found on the $PATH.
Signed-off-by: Andy Boyett <agb@agb.io>
(cherry picked from commit 591780615b)
commit 138c763 ("build: add --force option to gzip in Build/gzip")
added the --force flag to the gzip invocation.
Under environments with busybox gzip (e.g Alpine Linux), this fails
as busybox only recognizes "-f".
Signed-off-by: Mathew McBride <matt@traverse.com.au>
(cherry picked from commit fba168f574)
Backport a hot off the press upstream kernel ATM fix:
Preserve value of skb->truesize when accounting to vcc
"There's a hack in pskb_expand_head() to avoid adjusting skb->truesize
for certain skbs. Ideally it would cover ATM too. It doesn't. Just
stashing the accounted value and using it in atm_raw_pop() is probably
the easiest way to cope."
The issue was exposed by upstream with:
commit 14afee4b6092fde451ee17604e5f5c89da33e71e
Author: Reshetova, Elena <elena.reshetova@intel.com>
Date: Fri Jun 30 13:08:00 2017 +0300
net: convert sock.sk_wmem_alloc from atomic_t to refcount_t
But an earlier commit left the ticking timebomb:
158f323b9868 ("net: adjust skb->truesize in pskb_expand_head()
Sincerest thanks to Mathias Kresin <dev@kresin.me> for debugging
assistance and to David Woodhouse <dwmw2@infradead.org> for further
guidance, cajoling & patience in interpreting the debug I was giving him
and producing a fix!
Fixes FS#1567
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
(cherry picked from commit d600de3ddd)
Shorten the version string in Netgear factory image header in order
to enable u-boot TFTP recovery flash mode to work again.
Strip 'r7210-14cb05909a' into 'r7210' in the Netgear image header
by removing the hash (anything after "-").
background:
Some Netgear routers have recently been unable to flash Openwrt
factory image with the TFTP recovery flash mode provided by Netgear
u-boot. That is due to over-long Openwrt version string overflowing
into the router type string in u-boot code. Modern git versions
produce 10-digit short hashes for the Openwrt main repo, and that
causes the version string to be too long in the image header,
breaking the image ID verification by the TFTP flash routine.
(Other option could be to force a shorter hash in scripts/getver.sh,
but as the problem only concerns Netgear routers, let's patch just
them.)
More detailed explanations in FS#1583
Tested with WNDR3800
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
(cherry picked from commit dcfe2a461e)
The kernel patch *-mips_module_reloc.patch breaks dynamic ftrace as
dynamic ftrace depends on -mlong-calls.
See http://patchwork.linux-mips.org/patch/675/
Thus we always set -mlong-calls if the kernel is being
compiled with dynamic ftrace support.
Signed-off-by: Vincent Wiemann <webmaster@codefetch.de>
(cherry picked from commit 076d2ea682)
This fixup ip align in essedma driver rx path
see cat /proc/cpu/alignment
which reports alignment-fixups without this fix.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
(cherry picked from commit 8f804f42d5)
Marvell ahci hardware requires a workaround to prevent eSATA failures
on hotplug/reset when used with multi-bay external enclosures.
Errata Ref#226 - SATA Disk HOT swap issue when connected through Port
Multiplier in FIS-based Switching mode.
These patches backport the workaround from 4.17.
Signed-off-by: Jeremiah McConnell <miah@miah.com>
(cherry picked from commit e820455198)
Add procd file listeners to check files in `/etc/crontabs/`.
Also unified a bit the function style.
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit cbf69fb2ad)
zram.ko needs CONFIG_BLK_DEV activated and it is by default for all
other targets in OpenWrt.
This makes zram.ko compile again.
Compile tested only.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 6745af9a0d)
Neon and vfpv4 are mandatory extensions in the ARM64 instruction set
now, do not activate them explicitly. GCC will make use of these
extension now by default.
This makes it possible to share the toolchain with other Cortex A53
SoCs.
Compile tested only.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 10ce015c65)
Some of the Marvell targets have functional SATA port multiplier
support, which is required for multi-bay eSATA enclosures. Enable
kernel support by setting CONFIG_SATA_PMP.
Closes: FS#1232 and FS#547
Signed-off-by: Jeremiah McConnell <miah@miah.com>
(cherry picked from commit 390c4df2c0)
Without this change, ifx_mei_atm_showtime_check() will always return
"showtime" after one call of MEI_InternalXtmSwhowtimeEntrySignal()
was done, even if MEI_InternalXtmSwhowtimeExitSignal() was called
in the meantime.
The ifx_mei_atm_showtime_check() function is used by the ltq-atm and
ltq-ptm driver.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
(cherry picked from commit eee8ab59dc)
The ART partition of the Lima board stores exactly three mac addresses:
* 0x0: eth0
* 0x6: eth1
* 0x1002: wmac
The first two are correctly assigned in the mach file but the latter points
to 0x800. But this position is set to ff:ff:ff:ff:ff:ff. Luckily, the
driver falls back in ath9k_hw_init_macaddr to the EEPROM mac address when
it doesn't find a valid mac address in the platform_data.
Remove this bogus offset to the ART partition to directly load the wmac via
the EEPROM data in the ART partition.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
(cherry picked from commit 4f6320704f)
ipq806x is all dual core processors. ipq807x is quad core. Removes this
from dmesg:
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(cherry picked from commit fff65dbe24)
The mtd tool is built with different configurations depending on the
target. For example, brcm47xx adds the fixtrx subcommand, without which
an image fails when booting the second time.
Mark the mtd package as nonshared to really fix FS#484.
Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
(cherry picked from commit 46d7ced9d1)
Reboot the oxnas target based on Linux 4.14 by rebasing our support on
top of the now-existing upstream kernel support.
This commit brings oxnas support to the level of v4.17 having upstream
drivers for Ethernet, Serial and NAND flash.
Botch up OpenWrt's local drivers for EHCI, SATA and PCIe based on the
new platform code and device-tree.
Re-introduce base-files from old oxnas target which works for now but
needs further clean-up towards generic board support.
Functional issues:
* PCIe won't come up (hence no USB3 on Shuttle KD20)
* I2C bus of Akitio myCloud device is likely not to work (missing
debounce support in new pinctrl driver)
Code-style issues:
* plla/pllb needs further cleanup -- currently their users are writing
into the syscon regmap after acquireling the clk instead of using
defined clk_*_*() functions to setup multipliers and dividors.
* PCIe phy needs its own little driver.
* SATA driver is a monster and should be split into an mfd having
a raidctrl regmap, sata controller, sata ports and sata phy.
Tested on MitraStar STG-212 aka. Medion Akoya MD86xxx and Shuttle KD20.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(squash-picked commit 17511a7ea8 and commit dcc34574ef from master)
TP-Link TL-WR842N v5 are simple N300 router with 5-port FE switch and
non-detachable antennas. Its very similar to TP-Link TL-MR3420 V5.
Specification:
- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- USB 2.0 Port
- UART (J1) header on PCB (115200 8n1)
- 7x LED, 2x button, power input switch
Flash instruction:
The only way to flash OpenWrt image in wr842nv5 is to use
tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "lede-ramips-mt7628-tplink_tl-wr842n-v5-squashfs-tftp-recovery.bin"
to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed for around 6-7 seconds, until
device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
With this change, the LED trigger is independent from the (wireless)
netdev name. The (wireless) netdev name can be easiliy changed in
OpenWrt and would require an update of the netdev trigger settings each
time it is done.
This change is (for now) applied only to MT7628 devices from TP-Link, as
we only had the possibility to test this change against two of those
devices, namely a TL-WR841 v13 and a Archer C50 v3.
Signed-off-by: David Bauer <mail@david-bauer.net>
I found mt7688 watchdog not working. The watchdog registers are identical
for mt7621 and mt7628/mt7688. The first watchdog related register is at
0x10000100, the last one - a 16bit sized - at 0x10000128.
Set the correct register address and size in the dtsi file to get the
watchdog working.
Signed-off-by: lbzhung <gewalalb@gmail.com>
[add commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
73edb22 mt76: discard early received packets if not running yet
0b8d1dd mt76: fix beacon timer drift
20c0766 mt7603: adjust rx hang watchdog for MT7628
664e321 mt7603: add extra PSE hang check signature for MT7628
f24b56f update MT7628 firmware to the latest version
d87e4b0 mt7603: clear PSE reset bit if PSE reset fails
0ef26ef mt76: only stop tx queues on offchannel, not during the entire scan
f399da3 mt76: prevent tx scheduling during channel change
21c1e1e mt76: move ieee80211_hw allocation to common core
730c292 mt76: wait for pending tx to complete before switching channel
fcbb49e mt76x2: use udelay instead of usleep_range in mt76x2_mac_stop
792dbe0 mt7603: do not hold dev->mutex while flushing dev->mac_work
9090f9c mt76x2: fix threshold for gain adjustment
2cbaa57 mt76x2: fix swapped values for RXO-18 in gain control
a39ab70 mt76x2: adjust AGC control register 26 based on gain for VHT80
4936c0c mt76x2: clear false CCA counters after changing gain settings
1528fe7 mt76x2: fix variable gain adjustment range
f3522e1 mt76x2: add a debugfs file to dump agc calibration information
65e161b mt76x2: fix tracking rssi for dynamic gain adjustment
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This was caused by a race condition between offload teardown and
conntrack gc bumping the timeout of offloaded connections
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix condir option processing allowing to use the format
"<directory>[,<file-extension>......]," as documented on the dnsmasq man
page which previously resulted into bogus dir being created.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
On bcm53xx and brcm47xx, commands are passed to default_do_upgrade that
expect the image to be passed on stdin, rather than as an argument.
Fixes: 30f61a34b4 ("base-files: always use staged sysupgrade")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Import a revert-commit from Stanislaw Gruszka which significantly
improves WiFi performance on rt2x00 based hardware.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry-picked from commit f4a639a3d7)
This device has only one ethernet port.
Signed-off-by: Matthias Badaire <mbadaire@gmail.com>
[add the existing eth0 as lan block, shorten commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The AVM package selection partially broke with the addition of the
FRITZ!Box 4020. This commit restores the intended behavior.
Signed-off-by: David Bauer <mail@david-bauer.net>
Some of the ubi-tools in the upstream mtd-utils have been
broken by a bad patch upstream. It causes major breakage
during sysupgrade when the kernel, rootfs, ... volumes
are deleted in the wrong order.
This patch therefore reverts the faulty upstream commit which
fixes the bug.
linux-mtd mailing-list thread:
<http://lists.infradead.org/pipermail/linux-mtd/2018-June/081562.html>
Cc: John Crispin <john@phrozen.org>
Reported-by: L. Wayne Leach <LLeachii@aol.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit daf19649db)
Some devices like the Mikrotik RB912 only have 1 USB port
which is shared between an USB A type port, and the mini PCIe socket.
Toggling a gpio selects the output to which USB is connected.
Since kernel 4.9, gpio base is rounded up to a value of 32.
Commit 65da6f9ca1 ("ar71xx: fix secondary gpio controller base values") accounts correctly for that.
In this commit, rb912 sees it's value changed from AR934X_GPIO_COUNT (23) to 32
This means that the USB toggle gpio number actually also changes from 52 to 61.
But ..
Some of these GPIO numbers are also used in other locations, like the boardfile.
The author forgot to also change them over there.
Switching the USB port to mPCIe now shows my modem is correctly discovered again:
[ 2863.864471] usb 1-1: new high-speed USB device number 4 using ehci-platform
[ 2864.055303] usb 1-1: config 1 has an invalid interface number: 8 but max is 3
[ 2864.062728] usb 1-1: config 1 has no interface number 1
[ 2864.074567] qcserial 1-1:1.0: Qualcomm USB modem converter detected
[ 2864.081474] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB0
[ 2864.111960] qcserial 1-1:1.2: Qualcomm USB modem converter detected
[ 2864.118976] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB1
[ 2864.139808] qcserial 1-1:1.3: Qualcomm USB modem converter detected
[ 2864.146777] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB2
[ 2864.165276] qmi_wwan 1-1:1.8: cdc-wdm0: USB WDM device
[ 2864.171879] qmi_wwan 1-1:1.8 wwan0: register 'qmi_wwan' at usb-ehci-platform-1, WWAN/QMI device, 02:00:44:ed:3b:11
Fixes: 65da6f9ca1 ("ar71xx: fix secondary gpio controller base values")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Cc: Robin Leblon <robin.leblon@ncentric.com>
Cc: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 55b4b1eba0)
This reverts a change made in Sep 2017 [1] which introduced
MSG_DONTROUTE flag to prevent udhcpc from reaching out to servers on a
different subnet. That change violates RFC2131 by forcing fully
configured clients, who got their configurations through an offer
relayed by a DHCP relay, from renewing through a unicast request
directly to the DHCP server, resulting in the client resorting to
boradcasting lease extension requests instead of unicasting them,
further breaking RFC2131.
The problem with MSG_DONTROUTE appears when talking to a properly
configured DHCP server that rejects non-compliant requests. Such server
will reject lease extension attempts sent via broadcast rather than
unicast, as is the case with Finnish ISPs Telia and DNA as well as
Estonian ISP Starman. Once the lease expires without renewal, udhcpc
enters init mode, taking down the interfaces with it, and thus causing
interruption on every lease expiry. On some ISPs (such as the ones
mentioned above) that can be once every 10-20 minutes. The interruptions
appear in the logs as such:
----
udhcpc: sending renew to x.x.x.x
udhcpc: send: Network unreachable
udhcpc: sending renew to 0.0.0.0
udhcpc: sending renew to 0.0.0.0
...
udhcpc: lease lost, entering init state
Interface 'wan' has lost the connection
Interface 'wan' is now down
Network alias 'eth0' link is down
udhcpc: sending select for y.y.y.y
udhcpc: lease of y.y.y.y obtained, lease time 1200
Network alias 'eth0' link is up
Interface 'wan' is now up
----
During lease extension, a fully configured client should be able to
reach out to the server from which it recieved the lease for extension,
regardless in which network it is; that's up to the gateway to find. [2]
This patch ensures that.
[1]
http://lists.busybox.net/pipermail/busybox-cvs/2017-September/037402.html
[2]
https://www.netmanias.com/en/post/techdocs/6000/dhcp-network-protocol/
understanding-dhcp-relay-agents
Signed-off-by: Adi Shammout <adi.shammout@outlook.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
If log_file is specified, make sure its directory exists.
Signed-off-by: Karl Palsson <karlp@etactica.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
The kernel bump wrongly modified the patch
generic/pending-4.14/811-pci_disable_usb_common_quirks.patch.
Sync it from master.
Fixes: 1199a91095 ("kernel: bump 4.14 to 4.14.48 for 18.06")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Refreshed patches. The following patches were upstreamed and have been deleted:
* target/linux/lantiq/patches-4.14/0025-MIPS-lantiq-gphy-Remove-reboot-remove-reset-asserts.patch
* target/linux/generic/pending-4.14/101-clocksource-mips-gic-timer-fix-clocksource-counter-w.patch
* target/linux/generic/pending-4.14/103-MIPS-c-r4k-fix-data-corruption-related-to-cache-coherence.patch
* target/linux/generic/pending-4.14/181-net-usb-add-lte-modem-wistron-neweb-d18q1.patch
Compile-tested: ramips/mt7621, x86/64
Run-tested: ramips/mt7621
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Refreshed patches. The following patches were upstreamed and have been deleted:
* target/linux/ar71xx/patches-4.9/106-01-MIPS-ath79-fix-AR724X_PLL_REG_PCIE_CONFIG-offset.patch
* target/linux/generic/pending-4.9/180-net-phy-at803x-add-support-for-AT8032.patch
* target/linux/generic/pending-4.9/181-net-usb-add-lte-modem-wistron-neweb-d18q1.patch
* target/linux/generic/pending-4.9/182-net-qmi_wwan-add-BroadMobi-BM806U-2020-2033.patch
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
We recently increased the kernel partition size of the CPE/WBS 210/510.
This works fine for new installations of the factory image, but on
sysupgrades, the partition table read by the bootloader is not adjusted.
This limits the maximum size of the kernel loaded by the bootloader to the
old partition size.
While adjusting the partition table would be a cleanest solution, such a
migration would have to happen before an upgrade to a new version with a
newer kernel. This is error-prone and would require a two-step upgrade, as
we mark the partition table partition read-only.
Instead, switch from the lzma-loader with embedded kernel to the
okli-loader, so only the tiny lzma-loader is loaded by the bootloader as
"kernel", and the lzma-loader will then load the rest of the kernel by
itself.
Fixes: e39847ea2f ("ar71xx: increase kernel partition size for CPE/WBS 210/510")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
By making the kernel argv array const, the .data section can always be
omitted from the laoder binary.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
The text section in the ELF loader is aligned to the maximum page size,
which defaults to 64KB. Reduce it to the actual page size to avoid wasting
flash space for this alignment.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Some devices (TP-Link TL-WR1043ND v1) don't boot reliably when the
uncompressed loader is too small. This was workarounded in the loader by
adding 512KB of padding to the .data section of the loader binary.
This approach had two issues:
- The padding was only working when .data was non-empty (otherwise the
section would become NOBITS, omitting it in the binary). .data was only
empty when no CMDLINE was set, leading to further workarounds like
fe594bf90d ("ath79: fix loader-okli, lzma-loader"), and this
workaround was only effective because a missing "const" led to the kernel
argv being stored in .data instead of .rodata
- The padding was not only added to the compressed .gz loader, but also
uncompressed .bin and .elf loaders. The prevented embedding the kernel
cmdline in the loader for non-gz loader types.
To fix both issues, move the creation of the padding from the linker script
to the gzip step.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
There are several long-standing issues present in the UCI shell API as
documented in https://wiki.openwrt.org/doc/devel/config-scripting. They
relate both to high-level, user-defined callback functions used to
process UCI config files, and also to low-level functions used within
scripts generally.
The related problems have been encountered now and in the past, e.g.
https://forum.openwrt.org/viewtopic.php?id=54295, and include:
a) UCI parsing option() function and user-defined option_cb() callbacks
being erroneously called during processing of "list" config file entries;
b) normal usage of the low-level config_set() unexpectedy calling any
defined option_cb() if present; and
c) handling of the list_cb() not respecting the NO_CALLBACK variable.
Root causes include a function stack "inversion", where the low-level
config_set() function incorrectly calls the high-level option() function,
intended only for processing the "option" keyword of UCI config files.
This change addresses the inversion and other issues, making the option
handling code more consistent and smaller, and simplifying developers'
usage of UCI callbacks.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
The console bootarg is being corrupted on boot, causing various issues
including broken sysupgrade.
Utilising the bootargs mangle patch from other targets, hardcode the console
arguments and fetch the rootfs from the bootloader.
Kernel command line: console=ttyS0,115200 root=/dev/mtdblock8
Bootloader command line (ignored): console= root=/dev/mtdblock8
Please cherry pick to 18.06 too
Signed-off-by: Michael Gray <michael.gray@lantisproject.com>
(cherry picked from commit 4fdc6ca31b)
This version bump was made upstream mostly for OpenWRT, and should fix
an issue with a null dst when on the flow offloading path.
While we're at it, Kevin and I are the only people actually taking care
of this package, so trim the maintainer list a bit.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
This is a port of an old commit from mkresin's tree:
09260cdf3e9332978c2a474a58e93a6f2b55f4a8
This has the potential to break sysupgrade but it should be fine as
there is no stable release of LEDE or OpenWrt that support these devices.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(cherry picked from commit 9685f39787)
That commit exposed a bug in the DTS files used by mt7621 where the wrong
reg value for pcie1 (and potentially pcie2) was being used. This was
causing WiFi failures for interfaces in pcie1.
eg. 2.4GHz working but not 5GHz.
As all of these dts entries are already specified in mt7621.dtsi, remove
them.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(cherry picked from commit 02f815d190)
There's nothing connected to i2c on this board, so remove it.
Also edited the gpio group to match the PC2 as they're the same.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(cherry picked from commit 8c818fa1f0)
Switch ports 0..3 are connected to external ports LAN{1..4} in sequence,
switch port 4 is not used, and switch port 5 is connected to the CPU.
The WAN port is attached to the CPU's second network interface; it has no
connection to the internal switch.
Reuse the "Dell TrueMobile 2300" entry, which describes the same mapping.
Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
(cherry picked from commit 7ac238fc98)
The W25N01GV NAND is currently not used in any ipq806x device.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit a436ef992d)
There's no spi-nor in R7800, so disable unequipped interfaces.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit 8c1c1c4874)
These pins seem to be used by hw exclusively, so claiming it in
kernel causes an error in syslog in k4.14+.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit 96cd31655d)
EA8500 has pcie2 slot unequipped.
By EA8500 hw design default pcie2 reset gpio (gpio63) is used to
reset the switch. That's why enabling pcie2 brings the switch into
a working state.
So let's just control the gpio63 without enabling the pcie2 slot.
We have to remove the pcie2_pins node so the gpio63 is not defined
twice. Because pcie2 node has a reference to pcie2_pins we have to
remove it as well.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit 7f694ef3d9)
These nodes are common for all revisions so put it into SoC v1.0
dtsi file.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit 7a4f9c5993)
ipq8065 is ipq8064 v3.0
> socinfo_init: v6, id=280, ver=3.0, raw_id=17, raw_ver=17, hw_plat=0, hw_plat_ver=65536
Include dtsi accordingly and remove the unneeded qcom-ipq8065-v1.0.dtsi
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit e16f9abf6b)
According to OEM bootlog entry mass market devices are ipq8064 SoC
v2.0:
> socinfo_init: v6, id=202, ver=2.0, raw_id=2064, raw_ver=2064, hw_plat=0, hw_plat_ver=65536
I've checked C2600, EA8500 and VR2600v but couldn't find other
boards bootlog. I think it's safe to assume that other boards are
also v2.0. R7500 may be an exception because it was the first
device to hit the market.
So switch to v2.0 dtsi.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit 067036e875)
According to QCA internal numbering there are 3 versions of
ipq8064/5 SoC:
ipq8064 v1.0 - probably ipq8064 evaluation boards only
ipq8064 v2.0 - probably ipq8064 mass market boards only
ipq8064 v3.0 - aka ipq8065, boards based on ipq8065.
Each next revision includes configuration differences from
previous revision and adds something new.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit adbdf78049)
It keeps failing (R7800) with the stack trace below
BUG: scheduling while atomic: kworker/0:1/26/0x00000002
(unwind_backtrace) from [<c02121d0>] (show_stack+0x10/0x14)
(show_stack) from [<c03932e4>] (dump_stack+0x7c/0x9c)
(dump_stack) from [<c0239b90>] (__schedule_bug+0x5c/0x80)
(__schedule_bug) from [<c05b7260>] (__schedule+0x50/0x3f4)
(__schedule) from [<c05b76a8>] (schedule+0xa4/0xd4)
(schedule) from [<c05ba430>] (schedule_hrtimeout_range_clock+0xc8/0x100)
(schedule_hrtimeout_range_clock) from [<c05ba480>]
(schedule_hrtimeout_range+0x18/0x20)
(schedule_hrtimeout_range) from [<c05b9f78>] (usleep_range+0x48/0x50)
(usleep_range) from [<c03f333c>] (__clk_hfpll_enable+0x44/0xd0)
(__clk_hfpll_enable) from [<c03f3474>] (clk_hfpll_set_rate+0xac/0xc4)
(clk_hfpll_set_rate) from [<c03ec390>] (clk_change_rate+0xf4/0x1fc)
(clk_change_rate) from [<c03ec510>] (clk_core_set_rate_nolock+0x78/0x94)
(clk_core_set_rate_nolock) from [<c03ec54c>] (clk_set_rate+0x20/0x30)
(clk_set_rate) from [<c0424168>] (dev_pm_opp_set_rate+0x190/0x26c)
(dev_pm_opp_set_rate) from [<c04a8548>] (set_target+0x40/0x108)
(set_target) from [<c04a4.140>] (__cpufreq_driver_target+0x3f4/0x488)
(__cpufreq_driver_target) from [<c04a7494>] (od_dbs_timer+0xcc/0x154)
(od_dbs_timer) from [<c04a7998>] (dbs_work_handler+0x2c/0x54)
(dbs_work_handler) from [<c02309e8>] (process_one_work+0x1c0/0x2f0)
(process_one_work) from [<c02319a8>] (worker_thread+0x2a4/0x404)
(worker_thread) from [<c0235944>] (kthread+0xd8/0xe8)
(kthread) from [<c020eef0>] (ret_from_fork+0x14/0x24)
Signed-off-by: Marc Benoit <marcb62185@gmail.com>
[slh: rebase for kernel v4.14 as well]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit e40db2907e)
Starting with kernel 4.14 and gcc 7, the kernel doesn't fit into the
2 MB reserved for the kernel partition by the OEM firmware anymore.
This patch increases the kernel partition from 2 MB to 4 MB, at the
expense of the rootfs, for all supported kernels.
WARNING: This breaks sysupgrade! Flashing a firmware containing this
changed partitioning from an older image with 2 MB reserved for the
kernel partion requires the tftp recovery procedure, thereby losing
all settings.
This change follows the functional example of the Netgear r7800, but
has not been runtime tested on a Netgear Nighthawk X4 R7500v2.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit c3af761e47)
Starting with kernel 4.14 and gcc 7, the kernel doesn't fit into the
2 MB reserved for the kernel partition by the OEM firmware anymore.
This patch increases the kernel partition from 2 MB to 4 MB, at the
expense of the rootfs, for all supported kernels.
WARNING: This breaks sysupgrade! Flashing a firmware containing this
changed partitioning from an older image with 2 MB reserved for the
kernel partion requires the tftp recovery procedure, thereby losing
all settings.
This change follows the functional example of the Netgear r7800, but
has not been runtime tested on a Netgear Nighthawk X4 R7500
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
(cherry picked from commit c228bbe616)
Starting with kernel 4.14 and gcc 7, the kernel doesn't fit into the
2 MB reserved for the kernel partition by the OEM firmware anymore.
This patch increases the kernel partition from 2 MB to 4 MB, at the
expense of the rootfs, for all supported kernels.
WARNING: This breaks sysupgrade! Flashing a firmware containing this
changed partitioning from an older image with 2 MB reserved for the
kernel partion requires the tftp recovery procedure, thereby losing
all settings.
This change follows the functional example of the Netgear r7800, but
has not been runtime tested on a Netgear Nighthawk X4 D7800.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: Tathagata Das <tathagata@alumnux.com>
(cherry picked from commit 45b8a7c1a6)
The default image does not fit 2 MB anymore, expand kernel partition
to 3 MB.
Upgrading should work transparently via sysupgrade in both directions.
Another option would be to merge "kernel" and "rootfs" into a single
"firmware" partition using MTD_SPLIT_TPLINK_FW, but just changing the
sizes of the existing partitioning has been deemed safer in the absence
of an actual runtime test on an affected device; the maximum for rootfs
changes from 10.4 MB to 9.4 MB.
This change follows the example for the TP-Link Archer C2600, but has
not been runtime tested on a TP-Link Archer VR2600v.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: Sebastian Quilitz <zeraphim@x-pantion.de>
(cherry picked from commit 0c967d92b3)
The default image does not fit 2 MB anymore, expand os-image partition
to 4 MB.
Upgrading works transparently via sysupgrade in both directions.
Another option would have been to merge "os-image" and "rootfs" into a
single "firmware" partition using MTD_SPLIT_TPLINK_FW, but just
changing the sizes of the existing partitioning has been deemed safer
and actually tested on an affected device; the maximum for rootfs
changes from 27 MB to 25 MB.
Run-tested on TP-Link Archer C2600.
Signed-off-by: Joris de Vries <joris@apptrician.nl>
[slh: extend comments and commit message, rename rootfs]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit b72b36653a)
Starting with kernel 4.14 and gcc 7, the kernel doesn't fit into the
2 MB reserved for the kernel partition by the OEM firmware anymore.
This patch increases the kernel partition from 2 MB to 4 MB, at the
expense of the rootfs, for all supported kernels.
WARNING: This breaks sysupgrade! Flashing a firmware containing this
changed partitioning from an older image with 2 MB reserved for the
kernel partion requires the tftp recovery procedure, thereby losing
all settings.
This patch is based on a corresponding change by Pavel Kubelun
<be.dissent@gmail.com> and has been tested by Michael Yartys
<michael.yartys@protonmail.com>
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit dc50694bd1)
Disable MSM8960, MSM8974 and APQ8084
- since these are different SoC's than IPQ806x
Removed unrequired serial configs
- since ipq806x uses SERIAL_MSM only
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit 7ac6697fe2)
- Rebased the patches for 4.14
- Dropped spi-qup and 0027, 0028, 0029
clk patches since it's already included
in upstream.
Tested on IPQ AP148 Board:
1) NOR boot and NAND boot
2) Tested USB and PCIe interfaces
3) WDOG test
4) cpu frequency scaling
5) ethernet, 2G and 5G WiFi
6) ubi sysupgrade
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
(cherry picked from commit 93dd2f7211)
This commit adds an EVA flashable image for the FRITZ!Box 4040.
The image contains the U-Boot with OpenWRT appended to it. This way we
remove the need to use UART for initial flashing.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 70e6ea319d)
This commit adds an append-uboot command to append U-Boot from the
bin-directory.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 399495a952)
This commit alters the TP-Link Archer C50v3 LED settings to use the phy
trigger instead of the netdev one. This way the WiFi status is displayed
even if the wifi interface name is altered.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit ce91c85e01)
This commit fixes the wrong LED mapping of the Archer C50 v3.
Commit was tested with an EU device.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 35d00d9a41)
PISEN TS-D084 is an wireless router with a battery and integrated power supply based on Atheros AR9331.
Specification:
- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 1T1R 2.4 GHz (AR9331)
- 1x USB 2.0
Flash instruction:
The manufacturer are using exactly the same firmware header as TP-LINK TL-WR703N (including device ID!). Simply upload the factory firmware into WebUI and flashing is done.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
(cherry picked from commit a789c0f491)
THIN_ARCHIVES option is enabled by default in the kernel configuration
and no one target config disables it. So enable it by default and remove
this symbol from target specific configs to keep them light.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit 67a3cdcbb0)
New FUTEX_PI configuration symbol enabled if FUTEX and RT_MUTEX symbols
are enabled. Both of these symbols are enabled by default in the
generic config, so enable FUTEX_PI by default too to keep platform
specific configs minimal.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit bdc2b58c4b)
OVERLAY_FS config symbol selects EXPORTFS since 4.12 kernel, we have
OVERLAY_FS enabled by default, so enable EXPORTFS in the generic config
of 4.14 and remove this option from platform specific configs.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit a08b0d0c31)
DRM_LIB_RANDOM config symbol selected only by DRM_DEBUG_MM_SELFTEST
which is disable by default, so disable DRM_LIB_RANDOM by default too.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit 978543a246)
These options do not used by any supported arch, so disable them by
default to make arch configs a bit more clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit ead26e9db6)
Only one arch (x86_64) enables this option. So disable
ARCH_WANTS_THP_SWAP by default and remove referencies to it from all
configs (except x86_64) to make them clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit f928c338ad)
uClibc-ng 1.0.28 does not provide PF_VSOCK/AF_VSOCK definitions,
which causes iproute2 v4.16.0 compile errors.
In commit 57f2f80383b5 ("bits/socket.h: add missing defines")
necessary defines were included and iproute2 builds fine.
This commit now is part of uClibc-ng 1.0.30.
Lets update uClibc-ng to latest 1.0.30 version.
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: John Crispin <john@phrozen.org>
(cherry picked from commit 83e9262703)
Using a version number of 16 character causes a buffer overflow in the
version number overwriting the first bit of the signature in the
mkdapimg2 tool.
I am not sure if the version number should be null terminated or not.
This patch reduces the size of the version number by removing the number
of private commits from it.
This was the original version number which caused problems:
OpenWrt-r6727+10
Now it uses this version number:
OpenWrt-r6727
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit ae8ff1c65c)
Copy and refresh patches and config from 4.9, no more work is need.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit 3d69857ac1)
Disable CONFIG_EFI_VARS, since it suffers from sysfs limitation (no
support for variable longer than 1024 bytes).
kmod-fs-efivarfs is the replacement of this, which enables mounting
efivarfs file system and doesn't suffer from 1024 bytes limitation.
Signed-off-by: Alif M. Ahmad <alive4ever@live.com>
(cherry picked from commit b0a51dab8c)
Use ft_psk_generate_local=1 by default, as it makes everything else fairly
trivial. All of the r0kh/r1kh and key management stuff goes away and hostapd
fairly much does it all for us.
We do need to provide nas_identifier, which can be derived from the BSSID,
and we need to generate a mobility_domain, for which we default to the first
four chars of the md5sum of the SSID.
The complex manual setup should also still work, but the defaults also
now work easily out of the box. Verified by manually running hostapd
(with the autogenerated config) and watching the debug output:
wlan2: STA ac:37:43:a0:a6:ae WPA: FT authentication already completed - do not start 4-way handshake
This was previous submitted to LEDE in
https://github.com/lede-project/source/pull/1382
[dwmw2: Rewrote commit message]
Signed-off-by: Gospod Nassa <devianca@gmail.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
(cherry picked from commit 3cc56a5534)
Drop package/network/services/wireguard/patches/100-portability.patch
Instead pass 'PLATFORM=linux' to make since we are always building FOR
linux.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
(cherry picked from commit f06def4221)
BOCCO is a communication robot provided by YUKAI Engineering Inc.
SoC: MT7620A
MEM: 256MB
Flash: 8MB
NAND: 512MB (non support)
Include Sound DAC and AMP.
No Wired Ethernet.
Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
(cherry picked from commit d91953cb53)
Wifi button for WNDR3700 dual band routers has been renamed to "rfkill"
and its emitted keycode changed to KEY_RFKILL. This allows OpenWrt/LEDE
to support it 'out of the box' without additional tweaking.
Until this patch, button had been sending BTN_2 keycode which was
ignored by default (no action script present). To get expected behaviour
of switching radios on and off, user had to manually rename/link
'rfkill' script to name 'BTN_2' in /etc/rc.button directory.
This patch follows similar changes for other Netgear ar71xx routers,
for example WNR2000v3. It applies cleanly to both latest trunk and 17.01
branch. Tested on WNDR3700v1.
Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
(cherry picked from commit 45dc530334)
This patch adds a image with squashfs as the root filesystem.
A rootfs_data partition will be generated on the first boot
and placed inside the rootfs partition (just after the squashfs
image).
advantages:
- it is possible to migrate from an existing -ext4
installation and back via sysupgrade.
- existing partition layout will not be lost.
- slightly smaller image size.
- support for attendedsysupgrade
disadvantages:
- needs f2fs + tools as well. This is because fs-tools decides on the
blocksize of the sdcard. So either f2fs or ext4 can get choosen as
the rootfs_data filesystem (depends on the size of the root partition).
- rootfs_data is placed into the rootfs partition. This makes
it difficult for tools that expect a /dev/mmc0pX device.
It also makes it difficult for data recovery tools since they
might not expect to find a embedded partition or will be
confused.
For people with existing build configurations: make sure to include mkf2fs
and f2fsck package into the image... Otherwise the new -squashfs image will
boot of a ram-overlay and won't keep the configurations after a reboot.
Cc: Álvaro Fernández Rojas <noltari@gmail.com>
Cc: Paul Spooren <spooren@informatik.uni-leipzig.de>
Cc: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 707b6c815b)
There is a new APU-model available, APU3. The device is configured in
the same way as the APU1 and APU2, so the same LED/network setup can be
used.
I considered changing the case to pc-engines-apu*, but I chose to follow
the existing pattern and add the full board name.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
(cherry picked from commit 8f9baf5e1a)
This patch backports several patches that went upstream into
Herbert Xu's cryptodev-2.6 tree:
crypto: Use zeroing memory allocator instead of allocator/memset
crypto: crypto4xx - performance optimizations
crypto: crypto4xx - convert to skcipher
crypto: crypto4xx - avoid VLA use
crypto: crypto4xx - add aes-ctr support
crypto: crypto4xx - properly set IV after de- and encrypt
crypto: crypto4xx - extend aead fallback checks
crypto: crypto4xx - put temporary dst sg into request ctx
The older, outstanding patches from 120-wxyz series have been
upstreamed as well and therefore they have been reassigned to
fit into the series.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 16e39624b7)
The swconfig package is part of the DEFAULT_PACKAGES list in
the apm821xx's nand subtarget. It's enabled by default because
the MX60(W) and WNDR4700 need it for their initramfs. However
the package is not necessary for the MR24's sysupgrade image, as
the MR24 does not have a switch.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit e6e51ce87f)
Not sure how it worked before but ethernet is disabled
by default in ipq4019 dtsi.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
(cherry picked from commit 1f42deec8e)
- DGND3700v1: fix port numbers, they're in reverse order
- FaST2704n: there is no WAN port identified as such, only 4 LAN
- AD1018: configure the "FIBRE" port as WAN
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
(cherry picked from commit fbbb977772)
During handshake we are highjack and reset a LED to the configured trigger
afterwards. ltq-xdsl-app need to start after the LED init script, to
ensure that the LED init script doesn't re-highjack the LED we are
currently using for handshake indication.
Drop the comment about the atm dependency. The dependency was fixed quite
some time ago by using hotplug scripts for br2684ctl.
Signed-off-by: Mathias Kresin <dev@kresin.me>
(cherry picked from commit 0678cc850c)
Our pkg-config wrapper relies on the ability to redefine the $prefix and
$exec_prefix variables in order to construct proper search paths relative
to the build environment.
Patch the .pc file template to construct libdir, sharedlibdir and includedir
relative to the ${prefix} variable so that it can be overridden as needed.
This also fixes the libxml2/host build issue raised at
https://github.com/openwrt/packages/issues/6073 - it was caused by libxml2's
configure picking up a wrong host search path through zlib.pc, letting it
include the wrong endian.h, causing spurious member redeclaration errors in
system headers.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit 4da832e201)
Refreshed all patches
Added new ARM64 symbol: ARM64_ERRATUM_1024718
Compile-tested on: ar71xx
Runtime-tested on: ar71xx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This reverts commit c97189e26d
as it has different issues:
-Host file is not written in a directory unique per dnsmasq instance
-odhcpd writes host info into the same directory but still sends a SIGHUP to dnsmasq
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
1.) "addn-hosts" per default point to a file (but it supports directory)
2.) "hostsdir" only support directory with the additional benefit: New or changed files are read automatically.
Signed-off-by: Christian Schoenebeck <christian.schoenebeck@gmail.com>
The uboot-mvebu package incorrectly used the host pkg-config for the tool
build parts, which broke the build on systems lacking pkg-config and only
worked by accident on those that have it installed.
Export the host-build specific environment variables for the uboot build
to redirect pkg-config invocations to our staged host build pkg-config in
buildroot.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit 1289e00fff)
The uboot-mvebu package incorrectly used the host pkg-config for the tool
build parts, which broke the build on systems lacking pkg-config and only
worked by accident on those that have it installed.
Export the host-build specific environment variables for the uboot build
to redirect pkg-config invocations to our staged host build pkg-config in
buildroot.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit 208b984dda)
The uboot-mvebu package incorrectly used the host pkg-config for the tool
build parts, which broke the build on systems lacking pkg-config and only
worked by accident on those that have it installed.
Export the host-build specific environment variables for the uboot build
to redirect pkg-config invocations to our staged host build pkg-config in
buildroot.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit 01c2ce3c7d)
* chacha20poly1305: add mips32 implementation
"The OpenWRT Commit" - this significantly speeds up performance on cheap
plastic MIPS routers, and presumably the remaining MIPS32r2 super computers
out there.
* timers: reinitialize state on init
* timers: round up instead of down in slack_time
* timers: remove slack_time
* timers: clear send_keepalive timer on sending handshake response
* timers: no need to clear keepalive in persistent keepalive
Andrew He and I have helped simplify the timers and remove some old warts,
making the whole system a bit easier to analyze.
* tools: fix errno propagation and messages
Error messages are now more coherent.
* device: remove allowedips before individual peers
This avoids an O(n^2) traversal in favor of an O(n) one. Before systems with
many peers would grind when deleting the interface.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
When CONFIG_AUTOREMOVE is enabled, the build system touches an additional
".autoremove" stamp file in the cleaned build directory.
Since the autoremove stamp file is touched after the compile process
completed, it ends up being the most recent file of the package build
directory, causing the timestamp.pl check of depends.mk to erroneously
declare the ".built" and ".prepared" stamp files as stale, triggering
a forced clean-build submake process.
Fix the problem by using the ".built" stamp file as modification time
reference when touching the ".autoremove" stamp file.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit b287c82bed)
Includes the public usign certificates used by the 18.06.* release builds.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit 6d108c4a1a)
Also let the new openwrt-keyring package provide lede-keyring for backwards
compatibility.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit fd72e67ffe)
Following changes as part of the kernel
upstreaming attempts. And fix a slight fsck up
when calculating overheads for GSO packets.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
b2ecc52 mt76x2: fix avg_rssi estimation
fd58b28 mt76x2: add a polling delay in mt76x2_mac_stop routine
a78673d mt76: fix sending encrypted broadcast packets for secondary interfaces
e87f925 mt76x2: apply coverage class on slot time too
Signed-off-by: Felix Fietkau <nbd@nbd.name>
SUBMAKE=cmd(){$(SILENT)$(MAKE) -s "$$@" < /dev/null ||{echo"make $$*: build failed. Please re-run make with -j1 V=s or V=sc for a higher verbosity level to see what's going on"; false;}} 8>&1 9>&2; cmd
SUBMAKE=cmd(){$(SILENT)$(MAKE) -s $$* < /dev/null ||{echo"make $$*: build failed. Please re-run make with -j1 V=s to see what's going on"; false;}} 8>&1 9>&2; cmd
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
