Nanako/immortalwrt
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity

mediatek: add Imou LC-HX3001 support

Browse Source 
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 9777c5e853)
This commit is contained in:
Tianling Shen
2023-08-10 10:00:47 +08:00
parent f853776af6
commit 63caa6875f
6 changed files with 284 additions and 1 deletions
Download Patch File Download Diff File Expand all files Collapse all files

3
package/boot/uboot-envtools/files/mediatek_filogic
View File

@@ -40,6 +40,9 @@ bananapi,bpi-r3)
glinet,gl-mt3000)
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x80000" "0x20000"
;;
imou,lc-hx3001)
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x80000" "0x80000" "1"
;;
livinet,zr-3020|\
livinet,zr-3020-ubootmod|\
qihoo,360t7-ubootmod)

242
target/linux/mediatek/dts/mt7981b-imou-lc-hx3001.dts Normal file
View File

@@ -0,0 +1,242 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/*
* Copyright (C) 2023 Tianling Shen <cnsztl@immortalwrt.org>
*/
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "mt7981.dtsi"
/ {
model = "Imou LC-HX3001";
compatible = "imou,lc-hx3001", "mediatek,mt7981";
aliases {
led-boot = &power_led;
led-failsafe = &power_led;
led-running = &power_led;
led-upgrade = &power_led;
serial0 = &uart0;
};
chosen {
stdout-path = "serial0:115200n8";
};
memory {
reg = <0 0x40000000 0 0x10000000>;
};
gpio-keys {
compatible = "gpio-keys";
button-reset {
label = "reset";
linux,code = <KEY_RESTART>;
gpios = <&pio 1 GPIO_ACTIVE_LOW>;
};
button-mesh {
label = "mesh";
linux,code = <BTN_9>;
linux,input-type = <EV_SW>;
gpios = <&pio 0 GPIO_ACTIVE_LOW>;
};
};
gpio-leds {
compatible = "gpio-leds";
power_led: led-0 {
label = "green:power";
gpios = <&pio 4 GPIO_ACTIVE_LOW>;
};
led-1 {
label = "green:wlan";
gpios = <&pio 5 GPIO_ACTIVE_LOW>;
};
led-2 {
label = "red:wan";
gpios = <&pio 6 GPIO_ACTIVE_LOW>;
};
led-3 {
label = "green:wan";
gpios = <&pio 7 GPIO_ACTIVE_LOW>;
};
led-4 {
label = "green:lan";
gpios = <&pio 8 GPIO_ACTIVE_LOW>;
};
};
};
&eth {
pinctrl-names = "default";
pinctrl-0 = <&mdio_pins>;
status = "okay";
gmac0: mac@0 {
compatible = "mediatek,eth-mac";
reg = <0>;
phy-mode = "2500base-x";
fixed-link {
speed = <2500>;
full-duplex;
pause;
};
};
gmac1: mac@1 {
compatible = "mediatek,eth-mac";
reg = <1>;
phy-mode = "gmii";
phy-handle = <&int_gbe_phy>;
};
};
&mdio_bus {
switch: switch@0 {
compatible = "mediatek,mt7531";
reg = <31>;
reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>;
interrupt-controller;
#interrupt-cells = <1>;
interrupt-parent = <&pio>;
interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
};
};
&spi0 {
pinctrl-names = "default";
pinctrl-0 = <&spi0_flash_pins>;
status = "okay";
spi_nand: flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "spi-nand";
reg = <0>;
spi-max-frequency = <52000000>;
spi-cal-enable;
spi-cal-mode = "read-data";
spi-cal-datalen = <7>;
spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4E 0x41 0x4E 0x44>;
spi-cal-addrlen = <5>;
spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>;
spi-tx-buswidth = <4>;
spi-rx-buswidth = <4>;
mediatek,nmbm;
mediatek,bmt-max-ratio = <1>;
mediatek,bmt-max-reserved-blocks = <64>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "BL2";
reg = <0x00000 0x100000>;
};
partition@100000 {
label = "u-boot-env";
reg = <0x100000 0x80000>;
};
factory: partition@180000 {
label = "Factory";
reg = <0x180000 0x200000>;
};
partition@380000 {
label = "FIP";
reg = <0x380000 0x200000>;
};
partition@580000 {
label = "ubi";
reg = <0x580000 0x7280000>;
};
};
};
};
&switch {
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
label = "lan1";
};
port@1 {
reg = <1>;
label = "lan2";
};
port@2 {
reg = <2>;
label = "lan3";
};
port@6 {
reg = <6>;
ethernet = <&gmac0>;
phy-mode = "2500base-x";
fixed-link {
speed = <2500>;
full-duplex;
pause;
};
};
};
};
&pio {
spi0_flash_pins: spi0-pins {
mux {
function = "spi";
groups = "spi0", "spi0_wp_hold";
};
conf-pu {
pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
drive-strength = <8>;
bias-pull-up = <103>;
};
conf-pd {
pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
drive-strength = <8>;
bias-pull-down = <103>;
};
};
};
&uart0 {
status = "okay";
};
&watchdog {
status = "okay";
};
&wifi {
status = "okay";
mediatek,mtd-eeprom = <&factory 0x0>;
};

5
target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
View File

@@ -9,6 +9,11 @@ case $board in
cudy,wr3000-v1)
ucidef_set_led_netdev "wan" "wan" "blue:wan" "wan"
;;
imou,lc-hx3001)
ucidef_set_led_netdev "wan" "WAN" "green:wan" "eth1" "link"
ucidef_set_led_netdev "lan" "LAN" "green:lan" "eth0" "link"
ucidef_set_led_netdev "wlan" "WLAN" "green:wlan" "phy1-ap0" "link"
;;
livinet,zr-3020|\
livinet,zr-3020-ubootmod)
ucidef_set_led_netdev "internet" "INTERNET" "blue:internet" "wan"

8
target/linux/mediatek/filogic/base-files/etc/board.d/02_network
View File

@@ -33,7 +33,8 @@ mediatek_setup_interfaces()
glinet,gl-mt3000)
ucidef_set_interfaces_lan_wan eth1 eth0
;;
h3c,magic-nx30-pro)
h3c,magic-nx30-pro|\
imou,lc-hx3001)
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" eth1
;;
mediatek,mt7986a-rfb)
@@ -91,6 +92,11 @@ mediatek_setup_macs()
lan_mac=$(macaddr_add "$wan_mac" 1)
label_mac=$wan_mac
;;
imou,lc-hx3001)
lan_mac=$(mtd_get_mac_ascii u-boot-env mac)
[ -n "$lan_mac" ] || lan_mac=$(macaddr_add $(mtd_get_mac_binary Factory 0x4) -1)
wan_mac=$(macaddr_add $lan_mac 2)
;;
mercusys,mr90x-v1)
label_mac=$(get_mac_binary "/tmp/tp_data/default-mac" 0)
lan_mac=$label_mac

6
target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac
View File

@@ -48,6 +48,12 @@ case "$board" in
[ "$PHYNBR" = "0" ] && macaddr_add $addr 2 > /sys${DEVPATH}/macaddress
[ "$PHYNBR" = "1" ] && macaddr_add $addr 3 > /sys${DEVPATH}/macaddress
;;
imou,lc-hx3001)
addr=$(mtd_get_mac_ascii u-boot-env mac)
[ -n "$addr" ] || addr=$(macaddr_add $(mtd_get_mac_binary Factory 0x4) -1)
[ "$PHYNBR" = "0" ] && macaddr_add $addr 1 > /sys${DEVPATH}/macaddress
[ "$PHYNBR" = "1" ] && macaddr_add $addr 3 > /sys${DEVPATH}/macaddress
;;
jcg,q30-ubootmod)
[ "$PHYNBR" = "1" ] && \
macaddr_setbit_la "$(mtd_get_mac_binary Factory 0x4)" > /sys${DEVPATH}/macaddress

21
target/linux/mediatek/image/filogic.mk
View File

@@ -245,6 +245,27 @@ define Device/h3c_magic-nx30-pro
endef
TARGET_DEVICES += h3c_magic-nx30-pro
define Device/imou_lc-hx3001
DEVICE_VENDOR := Imou
DEVICE_MODEL := LC-HX3001
DEVICE_DTS := mt7981b-imou-lc-hx3001
DEVICE_DTS_DIR := ../dts
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware
UBINIZE_OPTS := -E 5
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 113152k
KERNEL_IN_UBI := 1
IMAGES += factory.bin
IMAGE/factory.bin := append-ubi | check-size $$$$(IMAGE_SIZE)
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
KERNEL = kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
KERNEL_INITRAMFS = kernel-bin | lzma | \
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd
endef
TARGET_DEVICES += imou_lc-hx3001
define Device/jcg_q30-ubootmod
DEVICE_VENDOR := JCG
DEVICE_MODEL := Q30 (custom U-Boot layout)